Scpi Command Reference, ABORt | HP E1368A manual

SCPI Command Reference

This section describes the Standard Commands for Programmable Instruments (SCPI) commands for the Microwave Switch modules. Commands are listed alphabetically by subsystem and also within each subsystem.

ABORt

The ABORt subsystem stops a scan in progress when the scan is enabled via the interface, and the trigger modes are TRIGger:SOURce BUS or TRIGger:SOURce HOLD.

Subsystem Syntax

ABORt

Comments ∙ ABORt Operation invalidates the current channel list and sets ARM:COUNt 1 (one scanning cycle per INITiate command), sets INITiate CONTinuous OFF (no continuous scanning cycles), and sets TRIGger:SOURce IMMediate (continuous internal triggering).

∙Stopping Scans Enabled from Interface: When a scan is enabled from the interface, use an interface CLEAR command or the HP E1301 front panel "Reset Instr" or "Clear Instr" key to stop the scan.

When the scan is enabled from the interface and the trigger source is

TRIGger:SOURce BUS or TRIGger:SOURce HOLD, use ABORt or the HP E1301 front panel "Reset Instr" or "Clear Instr" keys to stop the scan.

∙Stopping Scans Enabled from Front Panel: When a scan is enabled from the HP E1301 front panel, execute *RST over the interface or the front panel "Reset Instr" or "Clear Instr" keys to stop the scan.

∙Related Commands: ARM, INITiate:CONTinuous, [ROUTe:]SCAN, TRIGger

Example Stopping a Scan with ABORt

This example stops a (continuous) scan in progress.

TRIG:SOUR BUS	BUS is trigger source.
INIT:CONT ON	Set continuous scanning.
SCAN (@100:102)	Scan channels 00-02.
INIT	Starts scanning cycle, close
	channel 00.
ABOR	Aborts scan in progress.

50 HP E1368A/69A/70A Command Reference

Chapter 4

Image 50

HP E1368A manual Scpi Command Reference, Example Stopping a Scan with ABORt

Contents

Contents Open OPEN? Scan Scanmode SCANMODE? Cpon HP E1368A/69A/70A Modules User’s Manual Contents Certification Documentation History April According to ISO/IEC Guide 22 and ENPage Business Reply Mail Page Using This Chapter Microwave Switch Description Getting Started with the HP E1368A/69A/70A Chapter Power Supply Circuit HP E1368A Switches Programming the Microwave Switch Instrument Definition Card Numbers for Multiple-Module Switchboxes Example Reset the switchbox and close channel Initial Operation Configuring the HP E1368A/69A/70A Modules Setting the Address Switch Logical Address Selection Selecting the Interrupt Priority Interrupt Priority Selection Installing Switches on the HP E1369A Installing Switches on the Module Chapter Configuring the HP E1368A/69A/70A Modules Microwave Switch Installation Connecting Switches External To the Module Selecting Switch Power Connecting Field Wiring Selecting Switch Voltage Installing a Switch Or Attenuator on Module Microwave Switch/Attenuator Installation Shows the internal schematic of a single attenuator section Using the HP E1368A/69A/70A Modules Microwave Switch Commands Reset Conditions Switching Channels Example Single Channel Switching Power To connect C to Port 1, execute 33363K 33364K 33365K 33366K Example Multiple Channel Switching Using EXTernal Example Transfer Switch Using Two Port Switches Example Transfer Switch Using One Port Switch To route signal B to the output, execute Example 4 x 1 Multiplexer Scanning Channels Selects the Trigger Source Example Scanning Channels Output 722TRIG EXT … Example Using the Scan Complete Bit Example Multiple Channel Scanning 110END Detecting Error Conditions Recalling and Saving States Repeat Synchronizing the Microwave Switch Synchronizing Instruments Querying the Microwave Switch Scpi Command Format Command TypesCommon Command Format HP E1368A/69A/70A Command Reference Chapter Semicolon between the commands. For example Example Stopping a Scan with ABORt Scpi Command ReferenceABORt For the number of scanning cycles default is ∙ Number of Scans Use only numeric values between 1 Armcoun MONitorCARD Example Select Module #2 in a Switchbox for MonitoringDISPlay ∙ Selecting a Specific Module to be Monitored Use ∙ Selecting the Module to be Monitored Use Example Enabling the Monitor ModeExample Querying the Monitor Mode Example Enabling Continuous Scans ∙ Stopping Continuous Scans See the ABORt commandINITiate Example Query Continuous Scanning State Example Enabling Trig Out Port Example Query Trig Out Port Enable StateOUTPut ∙ Closing Channels To close Example Closing Microwave Switch ChannelsROUTe Example Opening Microwave Switch Channels ∙ Opening Channels To open Example Scanning Using External Device Or any combination Chapter HP E1368A/69A/70A Command Reference STATus ∙ Setting Bit 7 of the Status Byte Register Example Query the Standard Operation Status Enable Register STATOPER? SYSTem CDEScription? Example Reading the Model Number of a Card #1 Module Comments Microwave Switch Module Model NumberExample Reading the Error Queue TRIGger ∙ Executing the TRIGgerIMMediate Command a channel listExample Advancing Scan Using the TRIGger Command ∙ Hold or BUS Source Remains If selected, the TRIGgerSOURce ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Scanning Using External Triggers Scanning Using Bus Triggers Example Query the Trigger Source Ieee 488.2 Common Commands HP Command Module User’s Manual, or the ANSI/IEEE Standard Command Quick Reference Scpi Commands for Quick Reference HP E1368A/69A/70A Command Reference Chapter Connectors Used P1 No. Slots Characteristic Impedence 50Ω Insertion LossMaximum Input Power 1 Watt average Operating Temperature HP E1368A/69A/70A Specifications Appendix a HP E1368A/69A/70A Registers Register Definitions ID and Device Type Registers Addressing the RegistersReading the Registers Status/Control Register Channel Enable Register Writing to the Registers HP E1368A/69A/70A Registers Appendix B HP E1368A/69A/70A Error Messages Page Index HP E1368A/69A/70A Modules User’s Manual Index HP E1368A/69A/70A Modules User’s Manual Index HP-IB HP E1368A/69A/70A Modules User’s Manual Index HP E1368A/69A/70A Modules User’s Manual Index HP E1368A/69A/70A Modules User’s Manual Index