1100,0,1,Door contact,3,30 | Infinite Peripherals SCOM-100 specification

SCOM-100, User guide

22

s:Input signal name (Text: 0-15 characters, may include space characters)

a:Transition selection (0: No alarm, 1: positive 2: negative 3: both transitions)

d:Delay time in seconds (0-65535)

The following example illustrates how to configure digital input 1 to initiate an alarm SMS after any signal transition, a delay time of 30 seconds and a signal name configured to “Door contact”.

The configuration command would be:

1100,0,1,Door contact,3,30

Send an SMS to the SCOM-100 unit with the respective command.

Connect a contact or a loop wire to digital input 1 according to the wiring diagram in section 2.2. Close the contact/loop and leave it closed for more than 30 seconds. The S/R SMS LED will blink and you will receive an alarm SMS message and the following contents:

My SCOM-100

Door contact

POSITIVE ALARM

Now open the input contact/loop for 30 seconds. You will receive an alarm SMS message with the following contents:

My SCOM-100

Door contact

Image 22

Infinite Peripherals manual 1100,0,1,Door contact,3,30, My SCOM-100 Door contact

Contents

Page Disclaimer Contents Page Page Device overview Connections LED indications Wiring Power supply Digital inputs Digital outputs AC1 Analog inputs Analog input Vin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna Microphone Getting started Installing the SIM cardPreparing a SIM card First power up & factory settings Naming the unit SMS commandsDevice operation XXXX,A..A,..,..,Z..Z Configuring a digital input for alarming 1100,m,n,s,a,d 1100,0,1,Door contact,3,30 My SCOM-100 Door contact 0630,ID,s Setting alarm message’s texts1101,m,n,ID1,ID2 My SCOM-100 Door contact Door is opened 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100 Door contact Door is closed Clearing the digital input configuration1110,m,n 1000,m,n Setting a digital outputControlling the digital outputs 1000,0,2 1071,m,n Configuring an output as a closed contact1001,0,2 1071,0,2 1070,m,n Pulse digital output 1010,m,n,s Setting a digital output after a delay1010,0,2,25 Resetting a digital output after a delay 1020,m,n,h,mn 1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moff Time schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D 1030,m,n,ID 1700,1,0,800-120,1130-1001645-1801701,ID,P 1701,3,50 Clearing the digital output configuration1090,m,n,ID Analog input configuration Analog signal alarming1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 Setting alarm message’s texts for analog inputs1201,m,n,ID1,ID2 1210,m,n Clearing the analog input configurationSetting the analog inputs alarm deadband 1800,d 1 ON/OFF and PID control Special I/O Functions1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1255,id,sp 1251,id,s 1253,id 1252,id,m,n1260,id Create a new user User administration0500,id,n,p,c1,c2,c3 Set a DI alarm recipient Change user configurationDefining specific alarm recipients Delete a user Clear DI alarm recipients Set an AI alarm recipientClear AI alarm recipients RUN Control command Device status & mode controlsSetting the device status Monitor command 1105,m,n,v Controlling the device statusControlling the device response Send acknowledgement SMS Merge concurrent alarms Setting up an SMS counterResponse format Setting date and time Setting a GSM PIN 5100 Monitoring commandsMonitoring capabilities UNITMy SCOM-100 Connecting a PC Using the Hyperterminal for configuration SCOM-100, User guide SCOM-100, User guide Ate1 Using the Scom Configurator for configurationAtsms=1100,0,1,Door contact,3,30 Using the microphone input General parameter settings Command referenceAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unit GE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LED Default parameter values Factory settings GE-DIO-42 Digital I/O expansion Setting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN