1701,3,50, 1090,m,n,ID | Infinite Peripherals SCOM-100 manual


SCOM-100, User guide		35
1701:	Command ID
P:	Factor in % (0-100%). The ON duration
	of each program sequence is
	calculated by multiplicating this factor
	with the initial sequence duration.

Example:

Reducing the total ON duration of program 3 to the half:

1701,3,50

4.4.8 Clearing the digital output configuration

The command clears any output configurations related with multivibrator or time schedules:

1090,m,n,ID

1090:	Command ID
m:	Module number (0 for SCOM-100 main
	unit, 1-8 for DI-42 I/O expansion units)
n:	Output number (1-4 for SCOM-100
	main unit, 1-2 for DI-42 I/O expansion
	units)

Image 35

Infinite Peripherals SCOM-100 manual 1701,3,50, Clearing the digital output configuration, 1090,m,n,ID

Contents

Page Disclaimer Contents Page Page Connections Device overview LED indications Power supply Wiring Digital inputs AC1 Digital outputs Analog input Analog inputs Vin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide Microphone GSM antenna Preparing a SIM card Installing the SIM cardGetting started First power up & factory settings XXXX,A..A,..,..,Z..Z SMS commandsDevice operation Naming the unit 1100,m,n,s,a,d Configuring a digital input for alarming My SCOM-100 Door contact 1100,0,1,Door contact,3,30 1101,m,n,ID1,ID2 Setting alarm message’s texts0630,ID,s My SCOM-100 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100 Door contact Door is opened 1110,m,n Clearing the digital input configurationDoor contact Door is closed 1000,0,2 Setting a digital outputControlling the digital outputs 1000,m,n 1071,0,2 Configuring an output as a closed contact1001,0,2 1071,m,n Pulse digital output 1070,m,n 1010,0,2,25 Setting a digital output after a delay1010,m,n,s 1020,m,n,h,mn Resetting a digital output after a delay 1021,m,n,h,mn 1040,m,n,mon,moff Digital output time based scheduling 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D Time schedule program 1701,ID,P 1700,1,0,800-120,1130-1001645-1801030,m,n,ID 1090,m,n,ID Clearing the digital output configuration1701,3,50 1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d Analog signal alarmingAnalog input configuration ALH SCOM-100, User guide 1201,m,n,ID1,ID2 Setting alarm message’s texts for analog inputs1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 1800,d Clearing the analog input configurationSetting the analog inputs alarm deadband 1210,m,n 1250,id,m,n,m1,n1,sp,g,it,dt,ct,h Special I/O Functions1 ON/OFF and PID control 1251,id,s 1255,id,sp 1260,id 1252,id,m,n1253,id 0500,id,n,p,c1,c2,c3 User administrationCreate a new user Delete a user Change user configurationDefining specific alarm recipients Set a DI alarm recipient Clear AI alarm recipients Set an AI alarm recipientClear DI alarm recipients Monitor command Device status & mode controlsSetting the device status RUN Control command Send acknowledgement SMS Controlling the device statusControlling the device response 1105,m,n,v Response format Setting up an SMS counterMerge concurrent alarms Setting a GSM PIN Setting date and time UNITMy SCOM-100 Monitoring commandsMonitoring capabilities 5100 Using the Hyperterminal for configuration Connecting a PC SCOM-100, User guide SCOM-100, User guide Atsms=1100,0,1,Door contact,3,30 Using the Scom Configurator for configurationAte1 Using the microphone input Appendix Command referenceGeneral parameter settings SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Main unit Technical specifications GE-DIO-42 Digital I/O Expansion module Error handling LED Status LED indications GE-DIO-42 Digital I/O expansion Default parameter values Factory settings Setting an I/O expansion module address Dip switch settings Module number m PIN RS232C connector layout