Status LED indications, Led | Infinite Peripherals SCOM-100 instruction

SCOM-100, User guide

71

9.5 Status LED indications

9.5.1 Main unit

LED	Indication

POWER	Presence of power supply voltage

NETWORK	Blinking upon successful registration the GSM
	provider’s network

S/R SMS	Turns on during SMS receive or transmit

ERROR	• Turns on after start up:
	SIM card error
	Modem error
	Missing I/O expansion module
	Excessive EM noise or hardware error
	• Turns on during operation
	Modem error
	Excessive EM noise or hardware error

STATUS	ON: RUN (Control) state
	Blink: MONITOR state
	OFF: STOP state

READY	Blinking slowly: The unit starts up after power up
	(approx. 1 minute)
	Blinking fast: The unit starts after holding the start
	up button pressed during power up: Initialization
	process (approx. 1 minute)
	On: Unit start up completed OK
	Off with ERROR LED off: No user administrator
	found in SIM
	Off with ERROR LED on: See ERROR LED

Image 71

Infinite Peripherals SCOM-100 manual Status LED indications, Led

Contents

Page Disclaimer Contents Page Page Connections Device overview LED indications Power supply Wiring Digital inputs AC1 Digital outputs Analog input Analog inputs Vin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide Microphone GSM antenna Preparing a SIM card Installing the SIM cardGetting started First power up & factory settings XXXX,A..A,..,..,Z..Z SMS commandsDevice operation Naming the unit 1100,m,n,s,a,d Configuring a digital input for alarming My SCOM-100 Door contact 1100,0,1,Door contact,3,30 1101,m,n,ID1,ID2 Setting alarm message’s texts0630,ID,s My SCOM-100 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100 Door contact Door is opened 1110,m,n Clearing the digital input configurationDoor contact Door is closed 1000,0,2 Setting a digital outputControlling the digital outputs 1000,m,n 1071,0,2 Configuring an output as a closed contact1001,0,2 1071,m,n Pulse digital output 1070,m,n 1010,0,2,25 Setting a digital output after a delay1010,m,n,s 1020,m,n,h,mn Resetting a digital output after a delay 1021,m,n,h,mn 1040,m,n,mon,moff Digital output time based scheduling 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D Time schedule program 1701,ID,P 1700,1,0,800-120,1130-1001645-1801030,m,n,ID 1090,m,n,ID Clearing the digital output configuration1701,3,50 1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d Analog signal alarmingAnalog input configuration ALH SCOM-100, User guide 1201,m,n,ID1,ID2 Setting alarm message’s texts for analog inputs1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 1800,d Clearing the analog input configurationSetting the analog inputs alarm deadband 1210,m,n 1250,id,m,n,m1,n1,sp,g,it,dt,ct,h Special I/O Functions1 ON/OFF and PID control 1251,id,s 1255,id,sp 1260,id 1252,id,m,n1253,id 0500,id,n,p,c1,c2,c3 User administrationCreate a new user Delete a user Change user configurationDefining specific alarm recipients Set a DI alarm recipient Clear AI alarm recipients Set an AI alarm recipientClear DI alarm recipients Monitor command Device status & mode controlsSetting the device status RUN Control command Send acknowledgement SMS Controlling the device statusControlling the device response 1105,m,n,v Response format Setting up an SMS counterMerge concurrent alarms Setting a GSM PIN Setting date and time UNITMy SCOM-100 Monitoring commandsMonitoring capabilities 5100 Using the Hyperterminal for configuration Connecting a PC SCOM-100, User guide SCOM-100, User guide Atsms=1100,0,1,Door contact,3,30 Using the Scom Configurator for configurationAte1 Using the microphone input Appendix Command referenceGeneral parameter settings SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Main unit Technical specifications GE-DIO-42 Digital I/O Expansion module Error handling LED Status LED indications GE-DIO-42 Digital I/O expansion Default parameter values Factory settings Setting an I/O expansion module address Dip switch settings Module number m PIN RS232C connector layout