Wiring, Power supply | Infinite Peripherals SCOM-100 specs

SCOM-100, User guide

8

2. Wiring

SCOM-100 is a simple device, not requiring special technical background for configuration and operation.

However an electrical technician should undertake the installation of the device.

2.1 Power supply

Power supply requirements are: SCOM-100-12: 12VDC +/-15% SCOM-100-24: 24VDC +/-15%

A low ripple power supply output is recommended. Output voltage stabilization is not required.

See section 9.3.1 for details.

Image 8

Infinite Peripherals SCOM-100 manual Wiring, Power supply

Contents

Page Disclaimer Contents Page Page Device overview Connections LED indications Wiring Power supply Digital inputs Digital outputs AC1 Analog inputs Analog input Vin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna Microphone Preparing a SIM card Installing the SIM cardGetting started First power up & factory settings SMS commands Device operationNaming the unit XXXX,A..A,..,..,Z..Z Configuring a digital input for alarming 1100,m,n,s,a,d 1100,0,1,Door contact,3,30 My SCOM-100 Door contact 1101,m,n,ID1,ID2 Setting alarm message’s texts0630,ID,s 0630,1,Door is opened 0630,2,Door is closed 0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1My SCOM-100 Door contact Door is opened My SCOM-100 1110,m,n Clearing the digital input configurationDoor contact Door is closed Setting a digital output Controlling the digital outputs1000,m,n 1000,0,2 Configuring an output as a closed contact 1001,0,21071,m,n 1071,0,2 1070,m,n Pulse digital output 1010,0,2,25 Setting a digital output after a delay1010,m,n,s Resetting a digital output after a delay 1020,m,n,h,mn 1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moff Time schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D 1701,ID,P 1700,1,0,800-120,1130-1001645-1801030,m,n,ID 1090,m,n,ID Clearing the digital output configuration1701,3,50 1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d Analog signal alarmingAnalog input configuration ALH SCOM-100, User guide 1201,m,n,ID1,ID2 Setting alarm message’s texts for analog inputs1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 Clearing the analog input configuration Setting the analog inputs alarm deadband1210,m,n 1800,d 1250,id,m,n,m1,n1,sp,g,it,dt,ct,h Special I/O Functions1 ON/OFF and PID control 1255,id,sp 1251,id,s 1260,id 1252,id,m,n1253,id 0500,id,n,p,c1,c2,c3 User administrationCreate a new user Change user configuration Defining specific alarm recipientsSet a DI alarm recipient Delete a user Clear AI alarm recipients Set an AI alarm recipientClear DI alarm recipients Device status & mode controls Setting the device statusRUN Control command Monitor command Controlling the device status Controlling the device response1105,m,n,v Send acknowledgement SMS Response format Setting up an SMS counterMerge concurrent alarms Setting date and time Setting a GSM PIN Monitoring commands Monitoring capabilities5100 UNITMy SCOM-100 Connecting a PC Using the Hyperterminal for configuration SCOM-100, User guide SCOM-100, User guide Atsms=1100,0,1,Door contact,3,30 Using the Scom Configurator for configurationAte1 Using the microphone input Appendix Command referenceGeneral parameter settings SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unit GE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LED Default parameter values Factory settings GE-DIO-42 Digital I/O expansion Setting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN