Infinite Peripherals SCOM-100 specification

SCOM-100, User guide		67

	The unit does not send	The device is in STOP mode.
	an alarm SMS after a	The respective input is not activated
	digital input state	for alarming. Activate the input by
	changes.	sending the proper configuration
		command (See chapter 4.3).

	The analog value	Check sensor cabling for the
	readings through the	corresponding channel (see
	monitoring command	chapter 2.4)
	seem not to be correct.	Set the correct analog channel
		measurement parameters (see
		4.5.1).

	Alarm SMS of an analog	Set a higher alarm delay or a
	input come too	deadband value for the analog
	frequently.	inputs (see 4.5.4)

Image 67

Infinite Peripherals SCOM-100 manual

Contents

Page Disclaimer Contents Page Page Connections Device overview LED indications Power supply Wiring Digital inputs AC1 Digital outputs Analog input Analog inputs Vin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide Microphone GSM antenna Getting started Installing the SIM cardPreparing a SIM card First power up & factory settings XXXX,A..A,..,..,Z..Z SMS commandsDevice operation Naming the unit 1100,m,n,s,a,d Configuring a digital input for alarming My SCOM-100 Door contact 1100,0,1,Door contact,3,30 0630,ID,s Setting alarm message’s texts1101,m,n,ID1,ID2 My SCOM-100 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100 Door contact Door is opened Door contact Door is closed Clearing the digital input configuration1110,m,n 1000,0,2 Setting a digital outputControlling the digital outputs 1000,m,n 1071,0,2 Configuring an output as a closed contact1001,0,2 1071,m,n Pulse digital output 1070,m,n 1010,m,n,s Setting a digital output after a delay1010,0,2,25 1020,m,n,h,mn Resetting a digital output after a delay 1021,m,n,h,mn 1040,m,n,mon,moff Digital output time based scheduling 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D Time schedule program 1030,m,n,ID 1700,1,0,800-120,1130-1001645-1801701,ID,P 1701,3,50 Clearing the digital output configuration1090,m,n,ID Analog input configuration Analog signal alarming1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 Setting alarm message’s texts for analog inputs1201,m,n,ID1,ID2 1800,d Clearing the analog input configurationSetting the analog inputs alarm deadband 1210,m,n 1 ON/OFF and PID control Special I/O Functions1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1251,id,s 1255,id,sp 1253,id 1252,id,m,n1260,id Create a new user User administration0500,id,n,p,c1,c2,c3 Delete a user Change user configurationDefining specific alarm recipients Set a DI alarm recipient Clear DI alarm recipients Set an AI alarm recipientClear AI alarm recipients Monitor command Device status & mode controlsSetting the device status RUN Control command Send acknowledgement SMS Controlling the device statusControlling the device response 1105,m,n,v Merge concurrent alarms Setting up an SMS counterResponse format Setting a GSM PIN Setting date and time UNITMy SCOM-100 Monitoring commandsMonitoring capabilities 5100 Using the Hyperterminal for configuration Connecting a PC SCOM-100, User guide SCOM-100, User guide Ate1 Using the Scom Configurator for configurationAtsms=1100,0,1,Door contact,3,30 Using the microphone input General parameter settings Command referenceAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Main unit Technical specifications GE-DIO-42 Digital I/O Expansion module Error handling LED Status LED indications GE-DIO-42 Digital I/O expansion Default parameter values Factory settings Setting an I/O expansion module address Dip switch settings Module number m PIN RS232C connector layout