SCOM-100, User guide | Infinite Peripherals specs

SCOM-100, User guide

38

The following diagram illustrates the conversion characteristic:

The conversion values are given by the formula: Raw digital value:=4095 * Ix/20

Ix: Input current value (mA)

According to the formula, a 4mA input is converted to: Raw digital value=4095*4/20 = 819

This is the value setting for SSL.

A 20mA input is converted to a raw reading of 4095. This is the value setting for SSH.

SCOM-100 physical scale values are limited to integer values between -100,000 and 100,000. It is reasonable to select the physical scale in the range of 0 to 10,000 mBar to gain a better resolution.

The configuration command would then be:

Image 38

Infinite Peripherals manual SCOM-100, User guide

Contents

Page Disclaimer Contents Page Page Device overview Connections LED indications Wiring Power supply Digital inputs Digital outputs AC1 Analog inputs Analog input Vin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna Microphone Preparing a SIM card Installing the SIM cardGetting started First power up & factory settings Naming the unit SMS commandsDevice operation XXXX,A..A,..,..,Z..Z Configuring a digital input for alarming 1100,m,n,s,a,d 1100,0,1,Door contact,3,30 My SCOM-100 Door contact 1101,m,n,ID1,ID2 Setting alarm message’s texts0630,ID,s My SCOM-100 Door contact Door is opened 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100 1110,m,n Clearing the digital input configurationDoor contact Door is closed 1000,m,n Setting a digital outputControlling the digital outputs 1000,0,2 1071,m,n Configuring an output as a closed contact1001,0,2 1071,0,2 1070,m,n Pulse digital output 1010,0,2,25 Setting a digital output after a delay1010,m,n,s Resetting a digital output after a delay 1020,m,n,h,mn 1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moff Time schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D 1701,ID,P 1700,1,0,800-120,1130-1001645-1801030,m,n,ID 1090,m,n,ID Clearing the digital output configuration1701,3,50 1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d Analog signal alarmingAnalog input configuration ALH SCOM-100, User guide 1201,m,n,ID1,ID2 Setting alarm message’s texts for analog inputs1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 1210,m,n Clearing the analog input configurationSetting the analog inputs alarm deadband 1800,d 1250,id,m,n,m1,n1,sp,g,it,dt,ct,h Special I/O Functions1 ON/OFF and PID control 1255,id,sp 1251,id,s 1260,id 1252,id,m,n1253,id 0500,id,n,p,c1,c2,c3 User administrationCreate a new user Set a DI alarm recipient Change user configurationDefining specific alarm recipients Delete a user Clear AI alarm recipients Set an AI alarm recipientClear DI alarm recipients RUN Control command Device status & mode controlsSetting the device status Monitor command 1105,m,n,v Controlling the device statusControlling the device response Send acknowledgement SMS Response format Setting up an SMS counterMerge concurrent alarms Setting date and time Setting a GSM PIN 5100 Monitoring commandsMonitoring capabilities UNITMy SCOM-100 Connecting a PC Using the Hyperterminal for configuration SCOM-100, User guide SCOM-100, User guide Atsms=1100,0,1,Door contact,3,30 Using the Scom Configurator for configurationAte1 Using the microphone input Appendix Command referenceGeneral parameter settings SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unit GE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LED Default parameter values Factory settings GE-DIO-42 Digital I/O expansion Setting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN