Controlling the device status, 0621 | Infinite Peripherals SCOM-100

SCOM-100, User guide

48

The Status LED switches off and the unit enters the STOP state.

6.2 Controlling the device status

A digital input can be used to switch between RUN and MONITOR mode for power saving purposes.

1105,m,n,v
1105:	Command ID
m:	Module number (0 for SCOM-100 main
	unit, 1-8 for DI-42 I/O expansion units)
n:	DI input number (1-4)
v:	Input state for switching to MONITOR
	mode (0,1).

The function can be deactivated with the ‘Clear DI configuration command (See 4.3.2).

6.3 Controlling the device response

6.3.1 Send acknowledgement SMS

The device sends a typical acknowledgement response SMS to all configuration commands. The contained text in these SMS can be ‘COMMAND PROCESSED OK’ or ‘OK’ (according to the active answer mode Verbose or Brief) in case of successful command execution or All acknowledgement SMS send by the device can be cancelled using the command:

0621

Note: In the case of a rejected command, the error response SMS is always being sent.

The acknowledgement SMS can be restored using the command:

Image 48

Infinite Peripherals SCOM-100 manual Controlling the device status, Controlling the device response, 1105,m,n,v, 0621

Contents

Page Disclaimer Contents Page Page Device overview Connections LED indications Wiring Power supply Digital inputs Digital outputs AC1 Analog inputs Analog input Vin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna Microphone Installing the SIM card Getting startedPreparing a SIM card First power up & factory settings SMS commands Device operationNaming the unit XXXX,A..A,..,..,Z..Z Configuring a digital input for alarming 1100,m,n,s,a,d 1100,0,1,Door contact,3,30 My SCOM-100 Door contact Setting alarm message’s texts 0630,ID,s1101,m,n,ID1,ID2 0630,1,Door is opened 0630,2,Door is closed 0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1My SCOM-100 Door contact Door is opened My SCOM-100 Clearing the digital input configuration Door contact Door is closed1110,m,n Setting a digital output Controlling the digital outputs1000,m,n 1000,0,2 Configuring an output as a closed contact 1001,0,21071,m,n 1071,0,2 1070,m,n Pulse digital output Setting a digital output after a delay 1010,m,n,s1010,0,2,25 Resetting a digital output after a delay 1020,m,n,h,mn 1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moff Time schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D 1700,1,0,800-120,1130-1001645-180 1030,m,n,ID1701,ID,P Clearing the digital output configuration 1701,3,501090,m,n,ID Analog signal alarming Analog input configuration1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide Setting alarm message’s texts for analog inputs 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,151201,m,n,ID1,ID2 Clearing the analog input configuration Setting the analog inputs alarm deadband1210,m,n 1800,d Special I/O Functions 1 ON/OFF and PID control1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1255,id,sp 1251,id,s 1252,id,m,n 1253,id1260,id User administration Create a new user0500,id,n,p,c1,c2,c3 Change user configuration Defining specific alarm recipientsSet a DI alarm recipient Delete a user Set an AI alarm recipient Clear DI alarm recipientsClear AI alarm recipients Device status & mode controls Setting the device statusRUN Control command Monitor command Controlling the device status Controlling the device response1105,m,n,v Send acknowledgement SMS Setting up an SMS counter Merge concurrent alarmsResponse format Setting date and time Setting a GSM PIN Monitoring commands Monitoring capabilities5100 UNITMy SCOM-100 Connecting a PC Using the Hyperterminal for configuration SCOM-100, User guide SCOM-100, User guide Using the Scom Configurator for configuration Ate1Atsms=1100,0,1,Door contact,3,30 Using the microphone input Command reference General parameter settingsAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unit GE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LED Default parameter values Factory settings GE-DIO-42 Digital I/O expansion Setting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN