Limits, Parameter Range Units | Lincoln Electric IM892-C manual

B-34	OPERATION	B-34

LIMITS

Limits allow the welder to adjust the welding proce- dure only within a defined range.

Each user memory may have a different set of limits. For example, memory 1 can be set to limit the WFS to 200 through 300 in/min, and memory 2 can be set to limit the WFS to 275 through 310 in/min, while memo- ry 3 may not have any WFS limits.

Parameters are always constrained by machine limits. When memory limits are enabled, the parameter will flash whenever an attempt is made to exceed the memory limit value. The parameter will not flash if an attempt is made to exceed the machine limit.

Machine limits are:

Parameter	Range	Units
Wire Feed Speed	Weld mode dependent	in/min
	and gear box ratio
	dependent

Voltage	Weld mode dependent	Volts

Trim	0.50 to 1.50	--

Limits may be set for:

•Wire Feed Speed/Amperage

•Voltage/Trim

•Arc Control

Weld modes cannot be selected through the Limits Setup memu, and must be chosen and saved to mem- ory before entering the Limits Setup Menu.

Set Limits:

Press 5 seconds

MMEMORYM

PROCEDURE

A GUN B

1 2 3

HOLD 2 SECONDS TO SAVE

4 5 6

To set limits, press the desired memory button 1-6 and hold for 5 seconds. Release the memory button when the LED begins to blink rapidly and the MSP4 displays "Memory X Set Limits" as shown below.

MSP4 DISPLAY

	WAVEFORM CONTROL TECHNOLOGY
	Memory 1
IR PORT
	SETUP
	Set Limits
WELD MODE	START OPTIONS
ARC CONTROL	END OPTIONS
	SET

POWER FEED™ 25M

Image 50

Lincoln Electric IM892-C manual Parameter Range Units, Limits may be set for, MSP4 Display

Contents

Power Feed 25M Safety Electric Shock can kill Welding and Cutting Sparks can Cause fire or explosion Iii Précautions DE Sûreté Please Examine Carton and Equipment For Damage Immediately On-Line Product Registration Table of Contents Power Feed 25M Gearing WFS Range Wire SizesHeight Width Depth Weight Input Voltage ± 10% Input Amperes High Frequency Protection Safety PrecautionsLocation Electric Shock can Kill PIN Arclink Control CablesCable Connections Coaxial Weld Cable To installWeld Cable Size Table A.1 Build UP of Shielding GAS MAY Harm Health or Kill Electrode PolarityShielding GAS Connection Changing the Drive Motor Gear Ratio OFF Wire Drive Configuration Procedure to Install Drive Rolls and Wire Guides Remote Sense Lead Specifications Loading Spools of Wire Typical System Configurations Voltage Direct CurrentOpen Circuit Input Voltage Definition of Welding Terms Duty Cycle Equipment Limitations Recommended Power SourcesRecommended Processes Case Front Controls Code See Figure B.1 Case Front Controls Code 11456 Table B.1 ON-OFF SwitchStatus LED Definition Making a Weld with Waveform Technology Power Sources Smaw Stick Welding MSP4 Operation Process ModeSmaw Stick Welding Display NON-SYNERGIC Gmaw and Fcaw Welding Three non-synergic welding modes are available MSP4 Operation Non-Synergic Gmaw and Fcaw Welding Display Gmaw MIG Synergic Welding Figure B.5 Gmaw MIG Synergic Welding Display Synergic CV Voltage Display Steel and Stainless Synergic GMAW-P Pulsed MIG Welding ARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG Welding 220 Pulse-on-Pulse Welding Figure B.9 Aluminum GMAW-P and GMAW-PP Aluminum Pulse Welding Aluminum GMAW-P and GMAW-PP Welding Figure B.14 Aluminum Pulse and Pulse-On-Pulse Synergic Weld Display Weld Modes GMAW-STT Welding Figure B.15 GMAW-STT Weld Modes Tailout Peak Current Figure B.16Background Current Figure B.17 Gtaw TIG Welding Gtaw Tigwelding Figure B.17a Figure B.17a SET-UP Features Menu Figure B.17b Setup Menu User Defined Parameters Parameter Definition Procedure Change Method Stall Factor Adjustment Reset Consumable Weight Parameter Definition Gun Offset AdjustmentCrater Delay TIG Gas Control Sense From Studs 100 View DiagnosticsParameter Definition Push-Pull Gun Knob Behavior Show Test Modes 104 View Hardware Version Information 107 View Power Source ProtocolParameter Definition 103 View Software Version Information 105 View Welding Software Information 505 Setup Menu Lock Parameter Definition 503 Memory Button Disable504 Mode Select Panel Lock 506 Set User Interface Passcode Parameter Definition 507 UI Clear All Memories 509 UI Master Lockout PROCEDURE/MEMORY Panel OPERA- Tion User Memories Limits may be set for LimitsParameter Range Units MSP4 Display Parameter Name High LimitLow Limit Dual PROCEDURE/MEMORY Operation For Code 11456 and Higher Memory Set Limits 200 Memory Value Internal Controls for Code Description Internal Controls for Code 11456 and higher Escription Pressure ARM Adjustment Cold FEED/GAS Purge SwitchLight Switch Heater Switch Step Trigger Step Trigger OperationSTEP- Trigger Operation Code 11456 and higher Weld PreflowRUN-IN Postflow UpslopeBurnback Crater & Downslope Start & UpslopeCrater Figure B.22 Start Downslope Description Rear Controls Scfh Operation on Lincnet Power SourcesFlow Meter Liter/Min Drive Roll Kits Used Factory Installed EquipmentWire Type Electrode Size KP KIT K2593-xx #1 Co-Axial Power Cable K2683-xx Heavy Duty ArcLink Control Cable K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Water Cooled Guns Calibration Specification Routine MaintenancePeriodic Maintenance Troubleshooting Symptoms Description Possible Adjustments Output Problems Troubleshooting Wiring Diagram Power Feed 25M G5585 Diagrams Dimensions for Code Dimensions for Codes 11456 Precaucion Warnung