|
|
| TROUBLESHOOTING |
| |||
|
|
|
|
|
|
|
|
|
|
| Observe all Safety Guidelines detailed throughout this manual | ||||
|
|
|
|
|
|
|
|
|
|
| PROBLEMS |
| POSSIBLE |
| RECOMMENDED |
|
|
| (SYMPTOMS) |
| CAUSE |
| COURSE OF ACTION |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Fault Code |
| Description |
| Possible Adjustments |
| Err 006 | 1. | The wire feeder has not received | 1. | Verify the power source is operat- | ||
|
|
|
|
| a recognition command from the |
| ing properly. (Status light steady |
|
|
|
|
| power source. |
| green.) |
|
|
|
|
|
| 2. | Check control cable for loose or |
|
|
|
|
|
|
| broken leads. |
|
|
|
|
|
| 3. See power source Instruction | |
|
|
|
|
|
|
| Manual. |
|
|
|
|
|
|
| |
| Err 100 | 1. | The power source has issued a | 1. | Verify the power source is operat- | ||
|
|
|
|
| shutdown command. |
| ing properly (Status light steady |
|
|
|
|
|
|
| green.) |
|
|
|
|
|
| 2. | Check control cable for loose or |
|
|
|
|
|
|
| broken leads. |
|
|
|
|
|
| 3. See power source Instruction | |
|
|
|
|
|
|
| Manual. |
|
|
|
|
|
|
|
|
|
|
|
|
| ArcLink System Error Codes |
|
|
| Err 53 | Voltage sense loss. |
|
|
|
| |
|
|
|
|
|
|
| |
| Err 81 | Motor overload, long term. | 1. | The wire drive motor has over- | 1. | Check that the electrode slides | |
|
|
|
|
| heated. |
| easily through the gun and cable. |
|
|
|
|
|
| 2. | Remove tight bends from the gun |
|
|
|
|
|
|
| and cable. |
|
|
|
|
|
| 3. | Check that the spindle brake is |
|
|
|
|
|
|
| not too tight. |
|
|
|
|
|
| 4. | Verify a high quality electrode is |
|
|
|
|
|
|
| being used. |
|
|
|
|
|
| 5. | Wait for the error to reset and the |
|
|
|
|
|
|
| motor to cool. (approximately 1 |
|
|
|
|
|
|
| minute). |
|
|
|
|
|
|
| |
| Err 82 | Motor overload, short term. | 1. | The wire drive motor current draw | 1. | Check that motor can turn freely | |
|
|
|
|
| has exceeded limits, usually |
| when idle arm is open. |
|
|
|
|
| because the motor is in a locked | 2. | Verify that the gears are free of |
|
|
|
|
| rotor state. |
| debris and dirt. |
|
|
|
|
|
|
| |
| Err 95 | Spool gun or pull gun motor | 1. | The drive motor in the spool gun | 1. | Check that the wire moves freely | |
|
|
| overload. |
| or |
| through the gun when the gun is |
|
|
|
|
| much current. |
| straight. |
|
|
|
|
|
| 2. | Verify the correct size contact tip |
|
|
|
|
|
|
| is installed in the gun. |
|
|
|
|
|
|
| |
| Err 263 | No usable weld modes. | 1. | The power source does not have | 1. | See the power source Instruction | |
|
|
|
|
| any welding programs loaded. |
| Manual for load welding pro- |
|
|
|
|
|
|
| grams. |
|
|
|
|
|
|
|
|
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
