Memory Set Limits | Lincoln Electric IM892-C specs

B-37	OPERATION	B-37

LIMITS

Limits allow the welder to adjust the welding proce- dure only within a defined range.

Each user memory may have a different set of limits. For example, memory 1 can be set to limit the WFS to 200 through 300 in/min, and memory 2 can be set to limit the WFS to 275 through 310 in/min, while memo- ry 3 may not have any WFS limits.

Parameters are always constrained by machine limits. When memory limits are enabled, the parameter will flash whenever an attempt is made to exceed the memory limit value. The parameter will not flash if an attempt is made to exceed the machine limit.

The system machine limits are:

Parameter	Range		Units
Wire Feed Speed	Weld mode and wire		in/min
	feeder dependent.

Voltage	Weld mode dependent		Volts

Trim	0.50 to 1.50		--

Arc Control	-10.0 to 10.0		Weld mode dependent

Preflow	0.0 to 2.5		Seconds

Start Time	0.0 to 10.0		Seconds

Run-In WFS	Off, 50 to 150		in/min

Crater Time	0.0 to 10.0		Seconds

Burnback Time	0.00 to 0.25		Seconds

Postflow Time	0.0 to 10.0		Seconds

Limits may be set for:
• Wire Feed Speed/Amperage		• Start Time
• Voltage/Trim		• Burnback Time
• Arc Control		• Crater Wire Feed Speed
• Preflow Time		• Crater Voltage/Trim
• Run-In Speed		• Crater Time
• Start Wire Feed Speed		• Postflow Time
• Start Voltage/Trim

Weld modes cannot be selected through the Limits Setup memu, and must be chosen and saved to mem- ory before entering the Limits Setup Menu.

Set Limits:

Press 5 seconds

A GUN B

1 2 3 4

5 6 7 8

To set limits, press the desired memory button 1-8 and hold for 5 seconds. Release the memory button when the LED begins to blink rapidly and the MSP4 displays "Memory X Set Limits" as shown below.

MSP4 DISPLAY

Memory 2

Set Limits

WELD MODE	START OPTIONS
ARC CONTROL	END OPTIONS
	SET

POWER FEED™ 25M

Image 53

Lincoln Electric IM892-C manual Memory Set Limits

Contents

Power Feed 25M Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage Immediately Table of Contents Height Width Depth Weight Gearing WFS Range Wire SizesPower Feed 25M Input Voltage ± 10% Input Amperes Location Safety PrecautionsHigh Frequency Protection Electric Shock can Kill PIN Arclink Control CablesCable Connections Weld Cable Size To installCoaxial Weld Cable Table A.1 Build UP of Shielding GAS MAY Harm Health or Kill Electrode PolarityShielding GAS Connection OFF Changing the Drive Motor Gear Ratio Procedure to Install Drive Rolls and Wire Guides Wire Drive Configuration Loading Spools of Wire Remote Sense Lead Specifications Typical System Configurations Open Circuit Direct CurrentVoltage Input Voltage Duty Cycle Definition of Welding Terms Equipment Limitations Recommended Power SourcesRecommended Processes See Figure B.1 Case Front Controls Code Case Front Controls Code 11456 Status LED ON-OFF SwitchTable B.1 Definition Smaw Stick Welding Making a Weld with Waveform Technology Power Sources MSP4 Operation Process ModeSmaw Stick Welding Display Three non-synergic welding modes are available NON-SYNERGIC Gmaw and Fcaw Welding Non-Synergic Gmaw and Fcaw Welding Display MSP4 Operation Figure B.5 Gmaw MIG Synergic Welding Synergic CV Voltage Display Gmaw MIG Synergic Welding Display ARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG Welding Steel and Stainless Synergic GMAW-P Pulsed MIG Welding 220 Figure B.9 Pulse-on-Pulse Welding Aluminum Pulse Welding Aluminum GMAW-P and GMAW-PP Figure B.14 Aluminum GMAW-P and GMAW-PP Welding Weld Modes Aluminum Pulse and Pulse-On-Pulse Synergic Weld Display Figure B.15 GMAW-STT Welding Weld Modes GMAW-STT Tailout Peak Current Figure B.16Background Current Figure B.17 Gtaw TIG Welding Figure B.17a Gtaw Tigwelding Figure B.17a Figure B.17b Setup Menu SET-UP Features Menu User Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change Method Crater Delay Parameter Definition Gun Offset AdjustmentReset Consumable Weight TIG Gas Control Parameter Definition Push-Pull Gun Knob Behavior 100 View DiagnosticsSense From Studs Show Test Modes Parameter Definition 103 View Software Version Information 107 View Power Source Protocol104 View Hardware Version Information 105 View Welding Software Information 504 Mode Select Panel Lock Parameter Definition 503 Memory Button Disable505 Setup Menu Lock 506 Set User Interface Passcode 509 UI Master Lockout Parameter Definition 507 UI Clear All Memories User Memories PROCEDURE/MEMORY Panel OPERA- Tion Parameter Range Units LimitsLimits may be set for MSP4 Display Parameter Name High LimitLow Limit For Code 11456 and Higher Dual PROCEDURE/MEMORY Operation Memory Set Limits Memory Value 200 Description Internal Controls for Code Escription Internal Controls for Code 11456 and higher Light Switch Cold FEED/GAS Purge SwitchPressure ARM Adjustment Heater Switch STEP- Trigger Operation Step Trigger OperationStep Trigger Code 11456 and higher Weld PreflowRUN-IN Postflow UpslopeBurnback Crater & Downslope Start & UpslopeCrater Figure B.22 Downslope Start Rear Controls Description Flow Meter Operation on Lincnet Power SourcesScfh Liter/Min Drive Roll Kits Used Factory Installed EquipmentWire Type Electrode Size KP KIT K2593-xx #1 Co-Axial Power Cable K2683-xx Heavy Duty ArcLink Control Cable K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Water Cooled Guns Calibration Specification Routine MaintenancePeriodic Maintenance Troubleshooting Description Possible Adjustments Symptoms Output Problems Troubleshooting G5585 Wiring Diagram Power Feed 25M Diagrams Dimensions for Code Dimensions for Codes 11456 Precaucion Warnung