Connecting Workstations | METRObility Optical Systems 8124-01-M

10Mbps connections. All ports are hot pluggable. It is recommended you label each cable to identify the device or port at each end.

			10/100 Mbps Dual Speed Ethernet Hub
13x	14x	15x	16x	17x	18x	19x	20x	21x	22x	23x	24x
MDI-II											MDI-II
Switch Module
Installed
1x	2x			5x	6x	7x	8x	9x	10x	11x	12x

Shared Ports

Shared Ports

Connecting Devices

Connecting Workstations

Install either a 10BASE-T or a 100BASE-TX Fast Ethernet Network Interface Card into each workstation if not already installed. Using a UTP/STP cable, connect the Ethernet card (in the workstation) to a CenturyStack port.

Connecting Ethernet Hubs or Devices

Connect 10Mbps devices using UTP/STP Cat 3, 4 or 5 cables with RJ-45 connectors, enabling sending/receiving to or from other 10Mbps devices. By default, each port is set in auto sensing mode. CenturyStack can detect a 10BASE-T device and transmit/receive information to/from it.

CenturyStack 81XX

10Mbps

Connecting Ethernet Hubs

20 CenturyStack 8100 Managed Hub

Image 20

METRObility Optical Systems 8124-01-M manual Connecting Workstations, Connecting Ethernet Hubs or Devices

Contents

Lancast CenturyStack Managed Hub 10/100Mbps Page Installation Introduction CenturyStack 8100 Managed Hub Using Expansion ModulesManaging Through the Mini Console Master Hub Configuration & Console Management 123 Appendix 129 Introduction Overview of the CenturyStack 8100 Managed HubDual Speed CenturyStack Managed Hub 8112-01-M/S Dual Speed CenturyStack Managed Hub 8124-01-M/S Key Features 10/100Mbps Auto Sensing PortsStackability Expansion Slots Rmon Probe Capability Redundant Link Capacity Address Tracking CapabilitySource Address Search Capability Security Intrusion Control Capability Front Panel Overview Managed Slaves MDI-II Ports LED Panel Hub ID MDI-X Ports LED Indicators 12 Port LED Indication Forwarding LED* indicator meaning Front Panel Overview Master Units Console Keys MDI-II Ports Mini Console Hub ID MDI-X Ports Mini Console Rear Panel Overview Using Cascade Cables InstallationChoosing a Location Stacking Constructing a Management Hub Stack Position within the StackMaster Hub Role MiniConsoleManagement SNMPManagement ConsoleManagementWeb-BasedManagement Connecting Workstations Connecting Ethernet Hubs or Devices Connecting Fast Ethernet Switching Hubs Connecting the Other Dual Speed Hubs CenturyStack 8100 Managed Hub Using Expansion Modules Expansion Module OverviewInternal Bridge Function External Bridge Function Installing a Bridge Module Backpressure flow control Removing the Blank Module Panel TX Module LED Indicators FX Module LED Indicators FDX Module 8102-01-X Backpressure Jumpers ModuleModule 8102-01-X Bridge Jumpers Jumpers Module Module 8103-01-X Bridge Jumpers Module 8103-01-X Backpressure Jumpers JP7 JP2 Module 8102-03-X Backpressure Jumpers Module 8102-03-X Bridge JumpersDuplex Jumper JP2 INT EXT Module 8103-03-X Bridge Jumpers Module 8103-03-X Backpressure Jumpers JP3 CenturyStack 8100 Managed Hub Features Mini Console OverviewMini Console Display Panel Managing Through the Mini Console VFD Display Observing Basic Port Information Port Indicator Definition Console Keys Menu Tree Port Config SYS Locked Observing Network Traffic Selecting a Group Monitoring Port Statistics Port Statistic Counters Total errors received by the port including FCS Selecting a Port to Monitor Scrolling to a Port Monitoring Port Detail Information Monitoring All Ports Status ALL Ports Status Information Monitoring Individual Port Status Configuring Ports Configuring ALL POR TS Configuring a single port Unit Configuration Configuring the Unit Locking the Mini Console Unlocking the Mini Console Network Configuration IP AddressConfiguration IP Address DefaultGateway Out-of-Band ConfigurationSetting the Password SubnetMask Cancelling the Password Case You Forget Your Password Restoring System Default Setup Restarting the Hub System Information Menu System Information Connecting to the Console Interface Master Hub Configuration & Console Management Menu Convention Check Box Menu Title Master Hub Configuration & Console Management Using the Console Program Logging Main Menu Monitoring System Information Master Hub Configuration & Console Management Setting up for Management Management Capability Setup Enable or Disable Web access Local Console/Remote Telnet-Ethernet Local Console/Remote Telnet-SLIP Parity None Stop Bits 1 stop bit Out-of-BandMode Serial Port ConfigurationConsoleMode Out-of-Band Operation Mode Snmp Community Setup AccessRight Toaddacommunityname Toeditacommunityname Trap Receiver Setup Tosetupatrapreceivercommunityname Web-Based Management Configuration Out-of-Band Management Status Out-of-BandManagementControl Trap Filter Controlling Devices Repeater Group Control/StatusRepeater Port Control/Status Port Bridge Module Control/Status Repeater Group Control/Status GroupStatus GroupOperationalStatus GroupControl GroupReset Reset Function Logic OnlyTochangethesettingofagivengroup GroupLastChangeNotify Repeater Port Control/Status Isolate Status 100Mbps Port Only Indicates whether this PortControl Link StatusChange Notify Port Bridge Module Control/Status TP port with RJ-45 interface Multi-modewithSCtypeinterface Link Up Link DownOperate as Internal Plus External Bridge Operate as External Bridge Only External Function Admin State The default value is Disable Internal Function Admin State The default value is DisableExternal Port Link Status Change Notify When enabled, a BridgeModuleControl Redundant Link Control Master Hub Configuration & Console Management Configuring Link Pairs Editing a Link Pair Deleting a Link Pair Security Intrusion IntrusionStatus Intrusion Authentication Address AutoLearn Intrusion V iolation Monitoring the Network Repeater Statistics InformationRepeater Group Statistics Information Repeater Port Statistics Information Repeater Statistics Information Repeater Statistics Information Menu Relative Repeater Group Statistics Information Absolute Relative Repeater Port Statistics Information Repeater Port Statistics Information Menu Relative Master Hub Configuration & Console Management Symbol Errors 100Mbps only Total symbol errors for Address Tracking Information Source Address ChangesLast Source Source MAC Address T racking List a list of source MAC Address Tracking Information Menu list Address Search Information AddressSearchStatus Broadcast Storm Protection Broadcast AlarmStatus Port Broadcast Packet Rate Threshold The number FormulaforcalculatingBroadcastpacketrate Broadcast Storm Detected User Authentication Master Hub Configuration & Console Management System Utility System Download To download Tftp code, perform the following System Restart System Restart Menu Factory Reset Reset to factory default Login Timeout Interval Tftp Server IP Address Configuration Upload SettingConfiguration File Name Configuration Upload Request/Status Snmp Management Managing via MIB File Product Specifications Technical Information BOOTP/TFTP CUL UL & CSA Radio Frequency Interference Statements Product Safety and Compliance StatementsAgency Compliance Warranty and Servicing Information CenturyStack 8100 Managed Hub Appendix Mini Console Menu TreeAppendix Troubleshooting the Network Appendix