Multiplex Option | Multi-Tech Systems CDMA Wireless Modem manual

Chapter 17 – Extended AT Commands in IS707.3

Select Multiplex Option +CMUX

Description: The numeric parameter is used to select multiplex option.

Values:	<n>
	1: Multiplex Option 1
	2: Multiplex Option 2
Syntax:	Command syntax: AT+CMUX=<n>
	Command	Possible Responses
	AT+CMUX?	+CMUX: C, 2
	Note: Display the current setting.	OK
		Note: Command is valid
	AT+CMUX=?	+CMUX: (1-9,A-F), (1,2)
	Note: Display valid parameter range.	OK
		Note: Command is valid
	AT+CMUX=1	OK
	Note: Set multiplex option 1.	Note: Command is valid

Um Interface Fax Compression +CFC

Description:	The numeric parameter is used to set the Um Interface Fax Compression.
Values:	<Val>
	0: No compression
	1: V.42bis compression with parameters as set by the +CDS command
	2: Modified Read compression
	Note: Currently, the values 1 and 2 are not supported.
Syntax:	Command syntax: AT+CFC=<Val>
	Command	Possible Responses

	AT+CFC?	+CFC: 0
	Note: Display the current setting.	OK
		Note: Command is valid

	AT+CFC=?	+CFC: (0-2)
	Note: Display the range of the setting.	OK
		Note: Command is valid

	AT+CFC=0	OK
	Note: Set no compression.	Note: Command is valid

Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C

145

Image 145

Multi-Tech Systems CDMA Wireless Modem manual Select Multiplex Option +CMUX, Um Interface Fax Compression +CFC

Contents

AT Commands For Cdma Wireless Modems Reference Guide Revision Level Date Description AT Commands for Cdma Wireless ModemsMulti-Tech logo is a trademark of Multi-Tech Systems, Inc Country By Email By Phone Contents Call Control Commands Supplementary Services Commands Position Determination GPS AT Commands Provisioning AT Commands 124 Reference Information 166 AT Command Examples 171 Table of Contents Related References Scope of This Document Definitions Format message is supported Power from the base stations the mobile seesCdma revision of the mobile or base station PRL is loaded into the phone and is saved in NV-RAM Command Line Line SettingsInformation Responses and Result Codes Cell Broadcast Message Stored in Memory +CBMI Cell Broadcast Message Directly Displayed +CBMCell Environment Description Indication +CCED SMS Status Report Indication Directly Displayed +CDS Call Waiting Indication +CCWASMS Status Report Indication Stored in Memory +CDSI Values Callerid Caller ID Presentation +CLIP Key Press or Release +CKEVIncoming Message Directly Displayed +CMT Type Incoming Message Stored in Memory +CMTI Mode Preference +COPSRegistration & Roaming +CREG Values stat RxLev Indication +CSQ Incoming Call +CRINGIncoming Call +RING Call Connected +WCNT Call Answered +WANSCall Ended +WEND Values Call type Flash Indication +WFSH Feature Notification Message +WFNMResponse syntax +WEND reason ATH General Indicator +WIND Call Originated +WORG Command syntax AT+WIND=IndLevelCall Privacy Indication +WPRV Prv Roaming Indication +WROM Emergency Mode +WSOSRoam Flag Current NAM Change +WNAM Voice Mail Indicator +WVMISMS Message Storage Full +WMGF Leaving power save Entering power save Power Save +WSPSResponse Syntax +WSPS state State Electronic Serial Number +CGSN Request Revision Identification +CGMRSelect TE Character Set +CSCS Values Character Set Request Imsi +CIMI Repeat Last Command aCapabilities List +GCAP Phone Offline +CPOF Set Phone Functionality +CFUN Command syntax AT+CFUN=functionality levelValues Functionality level AT+CFUN? Command syntax AT+CMEE=error reporting flag Report Mobile Equipment Errors +CMEEPhone Activity Status +CPAS Keypad Control +CKPD Command syntax AT+CRMP=call type,volume,type,index Command syntax AT+CCLK=date and time stringClock Management +CCLK Ring Melody Playback +CRMP Subscriber Number +CNUM Ringer Sound Level +CRSLSelect Type of Address +CSTA Values Sound level Command syntax AT+WMSN View Modem Timers +WTMRModem Serial Number +WMSN AT+WTMR Command syntax ATDnb Dial Command DDirect Dial Syntax Command syntax ATDindex ATDmemname ATDmemindex Hang-Up Command HCommand syntax ATH Phonebook Syntax Command syntax ATA Extended Error Report +CEERCommand syntax AT+CEER Answer a Call a Dtmf Start and Stop Continuous +WSDT, +WSDS Dtmf Signals +VTD, +VTS Automatic Dialing with DTR %Dn Redial Last Telephone Number DLAutomatic Answer S0 Command syntax AT+CICB=mode Values ModeCommand syntax AT+CSNS Incoming Call Bearer +CICB Microphone Gain +VGT Volume Gain Control +VGR Speaker & Microphone Selection +SPEAKER Microphone Mute Control +CMUTValues ActiveSpkMic Side Tone Modification +SIDET Echo Cancellation +ECHOValues Val1 Val2 Initialize Voice Parameters +VIP TTY Mode +WTTYAT+VIP AT+WTTY Valid value ranges Represents an unknown signal quality Signal Quality +CSQAutomatic Cdma Only Cdma or Amps only Analog only AT+CSQ Band Band Preference +WBND Command syntax AT+WRMP=mode Home Networks only, as defined in the PRL default valueRoam Preference +WRMP Roaming on Affiliated networks, as defined in the PRL Stat Network Registration & Roaming +CREG Read Current NAM +WCNM Change NAM Selection +WNAMValues Nam AT+WSOS=1 Error Command syntax AT+WSOS=flagAT+WSOS? AT+WSOS=? Enable output of ERI indicators 64 through Suppress output of ERI indicators 64 throughCommand syntax AT+WRMW=value Extended Roam Indication +WRMW Enter PIN +CPIN SIM Card Operational Commands Enter PIN2 +CPIN2 Command syntax AT+CPINC Response syntax +CPINC n1,n2,k1,k2PIN Remaining Attempt Number +CPINC Passwd Facility Lock +CLCKAT+CLCK? AT+CLCK=AO,2 Card Identification +CCID Change Password +CPWDOldpwd Newpwd Parameters Definition New Message Acknowledgement +CNMA Select Message Service +CSMS Preferred Message Storage +CPMS Show Text Mode Parameters +CSDH Bfr New Message Indication +CNMI Oa/da Read Message +CMGR AT+CMGR=1 AT+CMGR=2 +CMS Error AT+CPMS=SR+CNMI=,,,2AT+CMSS=3 Index Place of storage in memory List Message +CMGLEncoding Length Length of the text message in bytes Da Destination address value in string format Send Message +CMGSCbn Call Back Number Send Message From Storage +CMSS Write Message to Memory +CMGW Delete Message +CMGD Command syntax AT+CMGD=Index ,DelFlagValues index DelFlag Select Broadcast Messages +CSCB Command syntax AT+CSCB=modeMessage Status Modification +WMSC Message Change SMS Status +WUSS Message Overwriting +WMGO Set Timestamp of MT SMS +WSTM Set SMS Compose Language and Encoding +WSCLValues Lang Enc Command syntax AT+CCFC= number Command e.g. ATD*72 ForwardedCall Forwarding +CCFC Number The phone number to forward all calls to Calling Line Identification Presentation +CLIP Calling Line Identification Restriction +CLIR AT+WFSH Send Flash to Base Station +WFSH List Current Call State +CLCC Select Mode +FCLASS Using AT Commands During a Data ConnectionSwitch From Online to Offline Mode Switch From Offline to Online Mode Disables reporting of local port rate Command syntax AT+CRCCommand syntax AT+ILRR=value Cellular Result Codes +CRC V42 Bis Data Compression +DS Command syntax AT+DS=dir,neg,P1,P2AT+DS? Disable reporting Enable reporting This syntax is for setting the +DR reporting methodCommand syntax AT+DR=val V42 Bis Data Compression Report +DR Fixed DTE Rate +IPR Command syntax AT+ICF= format, parityDTE-DCE Character Framing +ICF Values Format DTE-DCE Local Flow Control +IFC Set DCD Signal &C Set DSR Signal &S Set DTR Signal &DBack to Online Mode O Result Code Suppression Q Auto-Tests &T DCE Response FormatEcho E Values Num Command syntax AT&V Display Configuration &VAT&V Save Configuration &W Restore Factory Setting &FCommand syntax ATInum Request Identification Information Select Phonebook Memory Storage +CPBS Command syntax AT+CPBS=bkAT+CPBS=? AT+CPBS=EN AT+CPBS? Command syntax AT+CPBF=string Command syntax AT+CPBU?Return Selected Phonebook Locations +CPBU Find Phonebook Entries +CPBF String Write Phonebook Entry +CPBW+CME Erro AT+CPIN2? Ruim PIN2 Command syntax AT+CPBP= phone number Command syntax AT+CPBR=first,lastPhonebook Read +CPBR Phonebook Search +CPBP Delete Calls From Phonebook +WDCP Avoid Phonebook Init +WAIPValues Call phonebook Command syntax AT+WPDST=type This command sets and returns the PD session typePosition Determination Session Type +WPDST Session to provide the last position info available Position Determination Data Download +WPDDD Position Determination Operating Mode +WPDOMDuration Position Determination NV Privacy Level +WPPRV Position Determination Privacy Level +WPDPLTime Values Level Values Setting Position Determination Transport Setting +WPTLMCommand syntax AT+WPTLM=setting DBM Data Burse Message Position Determination Start Session +WPDSS Values ServicePosition Determination End Session +WPDES Performance AT+WPDSS=P Position Determination Start Session Result +WPDSSAT+WPDSS=PV Set Port of gpsOne Session +WPDPT Set IP Address of gpsOne Session +WPDIPValues Ipaddress Values Port Request Model Identification +WGMM Manufacturer Identification +WGMICell Environment and RxLev Indication +CCED Requested dump Command syntax AT+CCED=mode, requested dump Mobile Equipment Event Reporting +CMER Analog Digital Converters Measurements +ADC Write Gpio Value +WIOW Read Gpio Value +WIORGpio to read Value AT+WTONE? Play Tone +WTONEAT+WTONE=0 AT+WTONE=? Hardware Version +WHWV Play Dtmf Tone +WDTMFMode=1 Status Request +WSTR Select Voice Gain +WSVGValues Path 32kHz Sleep Mode +W32K Ring Indicator Mode +WRIM Default Change Default Melody +WCDMSoftware Version +WSSW Values Melody Custom Character Set +WCCS Command syntax AT+WCCS=mode,table,char 1,char Change Default Player +WCDP Cphs Command +CPHSFctId Status Set Standard Tone +WSST Reset +WRST Command syntax AT+WPRV=voice privacy level Normal default PrivateSet Voice Privacy Level +WPRV Values Voice privacy level AT+CSQ? +CME Error Command syntax AT+WPIN=mode,current val,new valSecurity PIN +WPIN Current val & new val Minute Alert +WMBP Request PRL Version Information +WPRLInterval Values Bitmap value Configure LED Indicator +CLEDBit Bit 2 bit7 Reserved Syntax Keypad disabled Keypad enabled Keypad Enable/Disable +WPADCommand syntax AT+WPAD=mode Summary Overview of SIM Application ToolKitFunctionality Profile Download Data Download to SIM Messages Exchanged During a SIM ToolKit OperationMenu Selection Call control by SIM 113 Timeout ConfigSIM ToolKit Set Facilities +STSF Autoresponse SIM ToolKit Indication +STIN Error CodesUnsolicited Result Last SIM Toolkit Indication AT+STIN? +CME ErrorAT+STIN? AT+STGI=0 SIM ToolKit Get Information +STGI Command syntax +STGI=Cmd+STGI=? +STGI Idx 1 Alpha Identifier menuNbItems 1 Alpha Idx Label CalledNb DefaultItem 1SubAdress Class Error Codes Values when Cmd=11 Setup Event ListUnsolicited Result SIM ToolKit Control Response +STCR Evt Values CmdType SIM ToolKit Give Response +STGR Possible Error Codes Values when CmdType=4 Setup callDetected Indication +STIN has not been received +STGR=? Command syntax +STGR=CmdType,Result,Data Mobile Directory Number +WMDN Service Programming Code +WSPCValues Lock type Code SID and NID +WSID Set Imsi +WIMISID number NID number Slot Cycle Index +WSCI Access Overload Class +WAOCPrimary Browser Gateway +WBGP Secondary Browser Gateway +WBGS Primary Cdma Channels +WPCC Packet Dial String +WPDSSecondary Cdma Channels +WSCC Values enable Service Option Management +WSOMCommit Changes +WCMT Home page SO 0 IS96A Read SID/NID Entries +WSNR Command syntax AT+WSNR=indexLocation in SID/NID list to read Error AT+WPDS? Service Programming ExampleAT+WSCI=1 AT+WCMT=0 Reset to Default Configuration Z0 Remote Async/Fax CommandSelect Tone Dialing T Command syntax ATSn=value Command syntax ATPSelect Pulse Dialing P Basic S-Registers SX Defaultlength Error Control Operation +EBNumeric Parameter Control +EFCS Values Breakselection Error Control Selection +ES Error Control Report +ERValues Origrqst Origfbk Error Control Selection +ETBM Error Control Selection +ESRTimer Values PendingTD Request Manufacture Identification +GMM Request Manufacture Identification +GMIRequest Revision Identification +GMR Request Global Object Identification +GOI Request Product Serial Number Identification +GSNModulation Selection +MS Modulation Reporting Control +MR Modulation Automode Control +MAReporting Control +MV18R Selection +MV18S FbktimeenableCellular Extension +CXT Dfltansmode Query Service +CAD Configuration String +CFGUm Interface Data Compression Reporting +CDR Command syntax AT+CRM=Val Command syntax AT+CDS=ValUm Interface Data Compression +CDS Set Rm Interface Protocol +CRM Command State Inactivity Timer +CQD Battery Charge +CBCCommand syntax AT+CQD=val Command syntax AT+CMIP AT+CBIP? Error Command syntax AT+CBIPBase Station IP Address +CBIP AT+CBIP? Values Class Serving System +CSSPA PF PCS Command syntax AT+CFC=Val Command syntax AT+CMUX=nSelect Multiplex Option +CMUX Um Interface Fax Compression +CFC IWF Content List +CGCAP Dial Command for Voice Calls +CDVHang-up Voice +CHV Command syntax AT+CGOI Um Packet Data Inactivity Timer +CTACommand syntax AT+CTA=val IWF Device Identification +CGOI IS-707.3 Fax Parameters IS-707.3 Fax Action Commands Command syntax AT$QCDMG Transition to Diagnostics Monitor $QCDMGCommand syntax AT$QCQNC=Val Quick Net Connect $QCQNC Originate M-to-M Packet Data Call $QCMTOM Protocol Revision in Use $QCPREVDump RLP Protocol Statistics $QCRLPD Values Number Reset PPP Protocol Statistics $QCPPPR Reset RLP Protocol Statistics $QCRLPRDump PPP Protocol Statistics $QCPPPD Dump IP Protocol Statistics $QCIPD Reset UDP Protocol Statistics $QCUDPR Reset IP Protocol Statistics $QCIPRDump UDP Protocol Statistics $QCUDPD Dump TCP Protocol Statistics $QCTCPD Set Data Service Option $QCSO Reset TCP Protocol Statistics $QCTCPRClear Mobile Error Log $QCCLR Answer Incoming Voice Call $QCCAV Pre-arrangement Setting $QCVADAutomatic Packet Detection $QCPKND Command syntax AT$QCRL3D Command syntax AT$QCMDR=ValSet DM Baud Rate $QCDMR Set Medium Data Rate $QCMDR SCRM’ing Selection $QCSCRM Reset RLP 3 Protocol Statistics $QCRL3RSCH Selection $QCTRTL SCH Selection $QCMIP Command syntax AT$QCMIP=ValAT$QCMIP? AT$QCMIP=? AT$QCMIP=0 RFC2002bis Selection $QCMIPT MIP Selection $QCMIPPCurrent Active Profile $QCMIPEP String The network access identifier text to be stored Command syntax AT$QCMIPGETP=ValCommand syntax AT$QCMIPNAI=String,Val Return Profile Information $QCMIPGETP Set MN-AAA Shared Secrets $QCMIPMASS Set Reverse Tunneling $QCMIPRT Set MN-AAA Shared Secrets $QCMIPMASSX Set MN-HA Shared Secrets $QCMIPMHSS Command syntax AT$QCMIPMASPI =SPI,Val Command syntax AT$QCMIPMHSSX =HEX,ValSet MN-HA Shared Secrets $QCMIPMHSSX Set MN-AAA Shared Secrets $QCMIPMASPI Command syntax AT$QCMIPPHA =IP,Val Command syntax AT$QCMIPMHSPI =SPI,ValSet MN-HA Shared Secrets $QCMIPMHSPI Set Primary HA IP Address $QCMIPPHA Command syntax AT$QCMIPHA =IP,Val Command syntax AT$QCMIPSHA =IP,ValSet Secondary HA IP Address $QCMIPSHA Set Home HA IP Address $QCMIPHA MS Error Result Code +CME Error error Specific Error Result Codes Message Service Failure Result Code +CMS Error errorExtended Error Report +CEER Call Processing Codes Final Result Codes Parameters Storage Intermediate Result Codes Code Meaning Codes for SMS-STATUS-REPORT +CDS and +CMGR AT Commands for Amps Operation AT Commands Supported When SIM Card Removed Examples Where a Voice Call is Originated Example 1 When the MS Has Already Been Powered OnExample When the MS is powered on Example with Incoming Calls Examples About Short Messages Example of a Call Waiting SituationExample 1 Receive a Short Message Example 2 Send a Short Message AT+WSCL=6,4 Example 3 Read Short Messages Status report Ind Message type indicatorMO delivery acknowledge message Mr Message Reference Roaming Indication +WROM Chapter Incoming Message Directly Displayed +CMT Chapter Enhanced Roaming Indication +WERI AT+WSOS +WSOS0 AT+COPS=0,0 Emergency Mode +WSOS Chapter Only if the message privacy value is 0 Normal Read message +CMGR Chapter 179 List Message +CMGL Chapter Command syntax AT+CMGL=statResponse syntax +CMGL index,stat,da/oa,lang Encod,lengthCRLFdata for SMS-DELIVER and SMS-SUBMIT, may be Reply Message reply option Send Message +CMGS ChapterNo Acknowledge Cbn CR entered text ctrl-Z / ESC Write Message to Memory +CMGW Chapter Verizon. System Selection +WVSS Service Programming Code +WSPC ChapterSyntax +WVSS pref Programming In Progress +WOT1 Initial Programming Required +WOT0Programming Successful +WOT2 Programming Unsuccessful +WOT3 NAM Download Ok +WOTN SPL Unlocked +WOTSMDM Download Ok +WOTM MSI Download Ok +WOTI Excess SPC Failures +WLCK Command syntax AT+WPLCK=levelPosition Determination Lock Level +WPLCK AT+WPLCK=? Response Syntax +CDS ind, mr, ra, tora, scts, dt, st Text mode AT+CSQ Use any four digit value. e.g Allow data calls Barr data calls Query statusSyntax for Facility Lock AT+CLCK=AO,9 190 Channel No service 800 MHz 1900 MHz Packet Zone Identifier +PZID Boot URL +WBURLTrusted Domain +WTDMN Wiota Connection Control +WIOTA Proxy Address +WDPXYSprint. System Selection +WSSS Preparing Data Services +WOAP Iota Error +WOAECommand syntax +WSUM? Please Retry +WOAR Command syntax +WRMM Reset MIN and MDN to factory defaults +WRMMAT+WRMM