Minute Alert +WMBP | Multi-Tech Systems CDMA Wireless Modem specs

		Chapter 14 – Specific AT Commands
Request PRL Version Information +WPRL
Description:	This command requests PRL Version information for the currently selected NAM.
Syntax:	Command syntax: AT+WPRL?
	Command	Possible Responses
	AT+WPRL?	+WPRL: 1024
	Note: Request current NAM’s PRL version	OK
	AT+WPRL?	+CME ERROR: 41
	Note: Request current NAM’s PRL version	Note: PRL request invalid because there’s no PRL loaded.

Note: The range for PRL is a 16-bit type.

Minute Alert +WMBP

Description:	This command is used to set the minute alert while in a voice conversation.
Values:	<mode>
	0: Disable alert
	1: Enable alert
	<interval>
	1 – 30: Time in minutes
Syntax:	Command syntax: AT+WMBP=<mode>,<interval>
	Command	Possible Responses
	AT+WMBP=0	OK
	Note: Turn off the alert
	AT+WMBP=1,4	OK
	Note: Turn on the alert and set 4 minutes apart
	AT+WMBP?	+WMBP: 1,4
	Note: Request current setting	Note: PRL request invalid because there’s no PRL
		loaded.
	AT+WMBP=?	+WMBP: (0-1),(1-30)
	Note: Display valid parameter ranges.

Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C

108

Image 108

Multi-Tech Systems CDMA Wireless Modem manual Request PRL Version Information +WPRL, Minute Alert +WMBP, Interval

Contents

AT Commands For Cdma Wireless Modems Reference Guide AT Commands for Cdma Wireless Modems Revision Level Date DescriptionMulti-Tech logo is a trademark of Multi-Tech Systems, Inc Country By Email By Phone Contents Call Control Commands Supplementary Services Commands Position Determination GPS AT Commands Provisioning AT Commands 124 Reference Information 166 AT Command Examples 171 Table of Contents Scope of This Document Related References Definitions Power from the base stations the mobile sees Format message is supportedCdma revision of the mobile or base station PRL is loaded into the phone and is saved in NV-RAM Line Settings Command LineInformation Responses and Result Codes Cell Broadcast Message Directly Displayed +CBM Cell Broadcast Message Stored in Memory +CBMICell Environment Description Indication +CCED Call Waiting Indication +CCWA SMS Status Report Indication Directly Displayed +CDSSMS Status Report Indication Stored in Memory +CDSI Values Callerid Key Press or Release +CKEV Caller ID Presentation +CLIPIncoming Message Directly Displayed +CMT Type Mode Preference +COPS Incoming Message Stored in Memory +CMTIRegistration & Roaming +CREG Values stat Incoming Call +CRING RxLev Indication +CSQIncoming Call +RING Call Answered +WANS Call Connected +WCNTCall Ended +WEND Values Call type Feature Notification Message +WFNM Flash Indication +WFSHResponse syntax +WEND reason ATH General Indicator +WIND Command syntax AT+WIND=IndLevel Call Originated +WORGCall Privacy Indication +WPRV Prv Emergency Mode +WSOS Roaming Indication +WROMRoam Flag Voice Mail Indicator +WVMI Current NAM Change +WNAMSMS Message Storage Full +WMGF Power Save +WSPS Leaving power save Entering power saveResponse Syntax +WSPS state State Request Revision Identification +CGMR Electronic Serial Number +CGSNSelect TE Character Set +CSCS Values Character Set Repeat Last Command a Request Imsi +CIMICapabilities List +GCAP Phone Offline +CPOF Command syntax AT+CFUN=functionality level Set Phone Functionality +CFUNValues Functionality level AT+CFUN? Report Mobile Equipment Errors +CMEE Command syntax AT+CMEE=error reporting flagPhone Activity Status +CPAS Keypad Control +CKPD Command syntax AT+CCLK=date and time string Command syntax AT+CRMP=call type,volume,type,indexClock Management +CCLK Ring Melody Playback +CRMP Ringer Sound Level +CRSL Subscriber Number +CNUMSelect Type of Address +CSTA Values Sound level View Modem Timers +WTMR Command syntax AT+WMSNModem Serial Number +WMSN AT+WTMR Dial Command D Command syntax ATDnbDirect Dial Syntax Hang-Up Command H Command syntax ATDindex ATDmemname ATDmemindexCommand syntax ATH Phonebook Syntax Extended Error Report +CEER Command syntax ATACommand syntax AT+CEER Answer a Call a Dtmf Signals +VTD, +VTS Dtmf Start and Stop Continuous +WSDT, +WSDS Redial Last Telephone Number DL Automatic Dialing with DTR %DnAutomatic Answer S0 Values Mode Command syntax AT+CICB=modeCommand syntax AT+CSNS Incoming Call Bearer +CICB Volume Gain Control +VGR Microphone Gain +VGT Microphone Mute Control +CMUT Speaker & Microphone Selection +SPEAKERValues ActiveSpkMic Echo Cancellation +ECHO Side Tone Modification +SIDETValues Val1 Val2 TTY Mode +WTTY Initialize Voice Parameters +VIPAT+VIP AT+WTTY Signal Quality +CSQ Valid value ranges Represents an unknown signal qualityAutomatic Cdma Only Cdma or Amps only Analog only AT+CSQ Band Preference +WBND Band Home Networks only, as defined in the PRL default value Command syntax AT+WRMP=modeRoam Preference +WRMP Roaming on Affiliated networks, as defined in the PRL Network Registration & Roaming +CREG Stat Change NAM Selection +WNAM Read Current NAM +WCNMValues Nam Command syntax AT+WSOS=flag AT+WSOS=1 ErrorAT+WSOS? AT+WSOS=? Suppress output of ERI indicators 64 through Enable output of ERI indicators 64 throughCommand syntax AT+WRMW=value Extended Roam Indication +WRMW SIM Card Operational Commands Enter PIN +CPIN Command syntax AT+CPINC Response syntax +CPINC n1,n2,k1,k2 Enter PIN2 +CPIN2PIN Remaining Attempt Number +CPINC Facility Lock +CLCK PasswdAT+CLCK? AT+CLCK=AO,2 Change Password +CPWD Card Identification +CCIDOldpwd Newpwd Parameters Definition Select Message Service +CSMS New Message Acknowledgement +CNMA Show Text Mode Parameters +CSDH Preferred Message Storage +CPMS New Message Indication +CNMI Bfr Read Message +CMGR Oa/da AT+CMGR=2 +CMS Error AT+CPMS=SR+CNMI=,,,2 AT+CMGR=1AT+CMSS=3 List Message +CMGL Index Place of storage in memoryEncoding Length Length of the text message in bytes Send Message +CMGS Da Destination address value in string formatCbn Call Back Number Write Message to Memory +CMGW Send Message From Storage +CMSS Command syntax AT+CMGD=Index ,DelFlag Delete Message +CMGDValues index DelFlag Command syntax AT+CSCB=mode Select Broadcast Messages +CSCBMessage Status Modification +WMSC Message Message Overwriting +WMGO Change SMS Status +WUSS Set SMS Compose Language and Encoding +WSCL Set Timestamp of MT SMS +WSTMValues Lang Enc Command e.g. ATD*72 Forwarded Command syntax AT+CCFC= numberCall Forwarding +CCFC Number The phone number to forward all calls to Calling Line Identification Restriction +CLIR Calling Line Identification Presentation +CLIP Send Flash to Base Station +WFSH AT+WFSH List Current Call State +CLCC Using AT Commands During a Data Connection Select Mode +FCLASSSwitch From Online to Offline Mode Switch From Offline to Online Mode Command syntax AT+CRC Disables reporting of local port rateCommand syntax AT+ILRR=value Cellular Result Codes +CRC Command syntax AT+DS=dir,neg,P1,P2 V42 Bis Data Compression +DSAT+DS? This syntax is for setting the +DR reporting method Disable reporting Enable reportingCommand syntax AT+DR=val V42 Bis Data Compression Report +DR Command syntax AT+ICF= format, parity Fixed DTE Rate +IPRDTE-DCE Character Framing +ICF Values Format Set DCD Signal &C DTE-DCE Local Flow Control +IFC Set DTR Signal &D Set DSR Signal &SBack to Online Mode O Result Code Suppression Q DCE Response Format Auto-Tests &TEcho E Values Num Display Configuration &V Command syntax AT&VAT&V Restore Factory Setting &F Save Configuration &WCommand syntax ATInum Request Identification Information Command syntax AT+CPBS=bk Select Phonebook Memory Storage +CPBSAT+CPBS=? AT+CPBS=EN AT+CPBS? Command syntax AT+CPBU? Command syntax AT+CPBF=stringReturn Selected Phonebook Locations +CPBU Find Phonebook Entries +CPBF Write Phonebook Entry +CPBW String+CME Erro AT+CPIN2? Ruim PIN2 Command syntax AT+CPBR=first,last Command syntax AT+CPBP= phone numberPhonebook Read +CPBR Phonebook Search +CPBP Avoid Phonebook Init +WAIP Delete Calls From Phonebook +WDCPValues Call phonebook This command sets and returns the PD session type Command syntax AT+WPDST=typePosition Determination Session Type +WPDST Session to provide the last position info available Position Determination Operating Mode +WPDOM Position Determination Data Download +WPDDDDuration Position Determination Privacy Level +WPDPL Position Determination NV Privacy Level +WPPRVTime Values Level Position Determination Transport Setting +WPTLM Values SettingCommand syntax AT+WPTLM=setting DBM Data Burse Message Values Service Position Determination Start Session +WPDSSPosition Determination End Session +WPDES Performance Position Determination Start Session Result +WPDSS AT+WPDSS=PAT+WPDSS=PV Set IP Address of gpsOne Session +WPDIP Set Port of gpsOne Session +WPDPTValues Ipaddress Values Port Manufacturer Identification +WGMI Request Model Identification +WGMMCell Environment and RxLev Indication +CCED Requested dump Command syntax AT+CCED=mode, requested dump Analog Digital Converters Measurements +ADC Mobile Equipment Event Reporting +CMER Read Gpio Value +WIOR Write Gpio Value +WIOWGpio to read Value Play Tone +WTONE AT+WTONE?AT+WTONE=0 AT+WTONE=? Play Dtmf Tone +WDTMF Hardware Version +WHWVMode=1 Select Voice Gain +WSVG Status Request +WSTRValues Path Ring Indicator Mode +WRIM 32kHz Sleep Mode +W32K Change Default Melody +WCDM DefaultSoftware Version +WSSW Values Melody Command syntax AT+WCCS=mode,table,char 1,char Custom Character Set +WCCS Cphs Command +CPHS Change Default Player +WCDPFctId Status Reset +WRST Set Standard Tone +WSST Normal default Private Command syntax AT+WPRV=voice privacy levelSet Voice Privacy Level +WPRV Values Voice privacy level Command syntax AT+WPIN=mode,current val,new val AT+CSQ? +CME ErrorSecurity PIN +WPIN Current val & new val Request PRL Version Information +WPRL Minute Alert +WMBPInterval Configure LED Indicator +CLED Values Bitmap valueBit Bit 2 bit7 Reserved Syntax Keypad Enable/Disable +WPAD Keypad disabled Keypad enabledCommand syntax AT+WPAD=mode Overview of SIM Application ToolKit SummaryFunctionality Profile Download Messages Exchanged During a SIM ToolKit Operation Data Download to SIMMenu Selection Call control by SIM 113 Config TimeoutSIM ToolKit Set Facilities +STSF Autoresponse Error Codes SIM ToolKit Indication +STINUnsolicited Result AT+STIN? +CME Error Last SIM Toolkit IndicationAT+STIN? AT+STGI=0 Command syntax +STGI=Cmd SIM ToolKit Get Information +STGI+STGI=? +STGI Alpha Identifier menu Idx 1NbItems 1 Alpha Idx Label DefaultItem 1 CalledNbSubAdress Class Values when Cmd=11 Setup Event List Error CodesUnsolicited Result SIM ToolKit Control Response +STCR Evt SIM ToolKit Give Response +STGR Values CmdType Values when CmdType=4 Setup call Possible Error CodesDetected Indication +STIN has not been received Command syntax +STGR=CmdType,Result,Data +STGR=? Service Programming Code +WSPC Mobile Directory Number +WMDNValues Lock type Code Set Imsi +WIMI SID and NID +WSIDSID number NID number Access Overload Class +WAOC Slot Cycle Index +WSCIPrimary Browser Gateway +WBGP Secondary Browser Gateway +WBGS Packet Dial String +WPDS Primary Cdma Channels +WPCCSecondary Cdma Channels +WSCC Service Option Management +WSOM Values enableCommit Changes +WCMT Home page SO 0 IS96A Command syntax AT+WSNR=index Read SID/NID Entries +WSNRLocation in SID/NID list to read Service Programming Example Error AT+WPDS?AT+WSCI=1 AT+WCMT=0 Remote Async/Fax Command Reset to Default Configuration Z0Select Tone Dialing T Command syntax ATP Command syntax ATSn=valueSelect Pulse Dialing P Basic S-Registers SX Error Control Operation +EB DefaultlengthNumeric Parameter Control +EFCS Values Breakselection Error Control Report +ER Error Control Selection +ESValues Origrqst Origfbk Error Control Selection +ESR Error Control Selection +ETBMTimer Values PendingTD Request Manufacture Identification +GMI Request Manufacture Identification +GMMRequest Revision Identification +GMR Request Product Serial Number Identification +GSN Request Global Object Identification +GOIModulation Selection +MS Modulation Automode Control +MA Modulation Reporting Control +MRReporting Control +MV18R Fbktimeenable Selection +MV18SCellular Extension +CXT Dfltansmode Configuration String +CFG Query Service +CADUm Interface Data Compression Reporting +CDR Command syntax AT+CDS=Val Command syntax AT+CRM=ValUm Interface Data Compression +CDS Set Rm Interface Protocol +CRM Battery Charge +CBC Command State Inactivity Timer +CQDCommand syntax AT+CQD=val Command syntax AT+CMIP Command syntax AT+CBIP AT+CBIP? ErrorBase Station IP Address +CBIP AT+CBIP? Serving System +CSS Values ClassPA PF PCS Command syntax AT+CMUX=n Command syntax AT+CFC=ValSelect Multiplex Option +CMUX Um Interface Fax Compression +CFC Dial Command for Voice Calls +CDV IWF Content List +CGCAPHang-up Voice +CHV Um Packet Data Inactivity Timer +CTA Command syntax AT+CGOICommand syntax AT+CTA=val IWF Device Identification +CGOI IS-707.3 Fax Parameters IS-707.3 Fax Action Commands Transition to Diagnostics Monitor $QCDMG Command syntax AT$QCDMGCommand syntax AT$QCQNC=Val Quick Net Connect $QCQNC Protocol Revision in Use $QCPREV Originate M-to-M Packet Data Call $QCMTOMDump RLP Protocol Statistics $QCRLPD Values Number Reset RLP Protocol Statistics $QCRLPR Reset PPP Protocol Statistics $QCPPPRDump PPP Protocol Statistics $QCPPPD Dump IP Protocol Statistics $QCIPD Reset IP Protocol Statistics $QCIPR Reset UDP Protocol Statistics $QCUDPRDump UDP Protocol Statistics $QCUDPD Dump TCP Protocol Statistics $QCTCPD Reset TCP Protocol Statistics $QCTCPR Set Data Service Option $QCSOClear Mobile Error Log $QCCLR Pre-arrangement Setting $QCVAD Answer Incoming Voice Call $QCCAVAutomatic Packet Detection $QCPKND Command syntax AT$QCMDR=Val Command syntax AT$QCRL3DSet DM Baud Rate $QCDMR Set Medium Data Rate $QCMDR Reset RLP 3 Protocol Statistics $QCRL3R SCRM’ing Selection $QCSCRMSCH Selection $QCTRTL Command syntax AT$QCMIP=Val SCH Selection $QCMIPAT$QCMIP? AT$QCMIP=? AT$QCMIP=0 MIP Selection $QCMIPP RFC2002bis Selection $QCMIPTCurrent Active Profile $QCMIPEP Command syntax AT$QCMIPGETP=Val String The network access identifier text to be storedCommand syntax AT$QCMIPNAI=String,Val Return Profile Information $QCMIPGETP Set Reverse Tunneling $QCMIPRT Set MN-AAA Shared Secrets $QCMIPMASS Set MN-HA Shared Secrets $QCMIPMHSS Set MN-AAA Shared Secrets $QCMIPMASSX Command syntax AT$QCMIPMHSSX =HEX,Val Command syntax AT$QCMIPMASPI =SPI,ValSet MN-HA Shared Secrets $QCMIPMHSSX Set MN-AAA Shared Secrets $QCMIPMASPI Command syntax AT$QCMIPMHSPI =SPI,Val Command syntax AT$QCMIPPHA =IP,ValSet MN-HA Shared Secrets $QCMIPMHSPI Set Primary HA IP Address $QCMIPPHA Command syntax AT$QCMIPSHA =IP,Val Command syntax AT$QCMIPHA =IP,ValSet Secondary HA IP Address $QCMIPSHA Set Home HA IP Address $QCMIPHA MS Error Result Code +CME Error error Message Service Failure Result Code +CMS Error error Specific Error Result CodesExtended Error Report +CEER Call Processing Codes Final Result Codes Intermediate Result Codes Parameters Storage Codes for SMS-STATUS-REPORT +CDS and +CMGR Code Meaning AT Commands Supported When SIM Card Removed AT Commands for Amps Operation Example 1 When the MS Has Already Been Powered On Examples Where a Voice Call is OriginatedExample When the MS is powered on Example with Incoming Calls Example of a Call Waiting Situation Examples About Short MessagesExample 1 Receive a Short Message Example 2 Send a Short Message Example 3 Read Short Messages AT+WSCL=6,4 Ind Message type indicator Status reportMO delivery acknowledge message Mr Message Reference Incoming Message Directly Displayed +CMT Chapter Roaming Indication +WROM Chapter Enhanced Roaming Indication +WERI Emergency Mode +WSOS Chapter AT+WSOS +WSOS0 AT+COPS=0,0 Read message +CMGR Chapter Only if the message privacy value is 0 Normal 179 Command syntax AT+CMGL=stat List Message +CMGL ChapterResponse syntax +CMGL index,stat,da/oa,lang Encod,lengthCRLFdata for SMS-DELIVER and SMS-SUBMIT, may be Send Message +CMGS Chapter Reply Message reply optionNo Acknowledge Write Message to Memory +CMGW Chapter Cbn CR entered text ctrl-Z / ESC Service Programming Code +WSPC Chapter Verizon. System Selection +WVSSSyntax +WVSS pref Initial Programming Required +WOT0 Programming In Progress +WOT1Programming Successful +WOT2 Programming Unsuccessful +WOT3 SPL Unlocked +WOTS NAM Download Ok +WOTNMDM Download Ok +WOTM MSI Download Ok +WOTI Command syntax AT+WPLCK=level Excess SPC Failures +WLCKPosition Determination Lock Level +WPLCK AT+WPLCK=? +CDS ind, mr, ra, tora, scts, dt, st Text mode Response Syntax AT+CSQ Allow data calls Barr data calls Query status Use any four digit value. e.gSyntax for Facility Lock AT+CLCK=AO,9 190 No service 800 MHz 1900 MHz Channel Boot URL +WBURL Packet Zone Identifier +PZIDTrusted Domain +WTDMN Proxy Address +WDPXY Wiota Connection Control +WIOTASprint. System Selection +WSSS Iota Error +WOAE Preparing Data Services +WOAPCommand syntax +WSUM? Please Retry +WOAR Reset MIN and MDN to factory defaults +WRMM Command syntax +WRMMAT+WRMM