IR1200 GPS-Enabled Modem | Nextel comm instruction

Overview

Ignition Sense /

Bypass

Connector

Modem									12VDC Power




Serial Data
Serial Data										Connector
Connector										Connector
Connector

Modem Antenna

Connector

Figure 2. Rear Panel of iR1200 Rugged Modem

iR1200 GPS-Enabled Modem

The following diagram displays components on the rear panel of the iR1200 GPS-Enabled Modem.

	GPS Serial	GPS Antenna	Ignition Sense /
		Connector	Bypass
	Data
			Connector
	Connector

	Modem			12VDC Power
	Serial Data
		Modem Antenna		Connector
	Connector
		Connector

Figure 3. Rear Panel of iR1200 GPS-Enabled Modem

RFM-4002-5015 Rev 3

11

Image 21

Nextel comm manual IR1200 GPS-Enabled Modem, Rear Panel of iR1200 Rugged Modem

Contents

Administrator’s Guide General Page Table of Contents Circuit Switched Data Modem Configuration Windows NT Saving AT Settings GPS Default Parameters Registers Pacemakers Hearing Aids Please Read Safety Notice on Before using the iR1200 Modem Page Table of Figures Table of Figures Nextel.com Declaration of Conformity FCC Compliance IR1200 Modem How to Order Required ComponentsDescription Online Documentation Introduction Using This GuideWelcome to Nextel Nextel Coverage Nextel Customer Care General Overview Overview Modem Configurations Modem Operating ModesIR1200 Rugged Modem Rear Panel of iR1200 Rugged Modem IR1200 GPS-Enabled Modem LED Modem Specifications External LED IR1200 Modem Getting Started Connecting the Modem Cabling Diagram Fixed Environment Signal Color Indication Communication Indicators CTS Status Packet Data IR1200 Modem Hardware and Installation Requirements Installing iDEN Packet Data Applet Download Software Instructions Before You Begin Windows 95/98/ME Computer Click Next on the iDEN Packet Data Applet Setup screen Program will check the communication settings and attempt Windows NT Click Next on the iDEN Packet Data Applet Setup screen Modem Installation Finish window opens. Click Finish Installing iDEN Packet Data Applet Multiple Baudrate should be unchecked Baud Rate 19200 bps Windows Click Next on the iDEN Packet Data Applet Setup screen That your modem is connected and click Next Multiple Baudrate should be unchecked Baud Rate 19200 bps Setting Up Windows Components Click Cancel to close the Make New Connection windowVerify Dial-Up Networking Verify TCP/IP Protocol Installation Click OK to close the Select Network Protocol window Windows NT/2000 Settings Select Control Panel Installing the Dial-Up Adapter Connection wizard. Click Next Manual Modem Configuration Modem Configuration Windows 95/98/MEInstall the Modem Configure the Modem Driver Click OK to close the Advanced Connection Settings window Use Flow Control Hardware RTS/CTSCreate a Dial-up Networking Connection Under Type of Dial-Up Server, select PPP Modem Configuration Windows NT Modem Installation Finish window opens. Click Finish Configure the Modem Driver Wizard Finish window opens. Click Finish Edit entry and modem properties from the drop-down list Modem Configuration Windows Create and Configure a Dial-up Networking Connection Nextel.com Modify Dial-up Connection Parameters IR1200 Modem Modem Profiles and Settings Connection Description screen appears HyperTerminal Setup Bits Per second Data Bits Parity None Stop Bits Flow Control Hardware Opening a HyperTerminal SessionWindows 2000/XP/Windows Windows NT Configuring With AT Commands Restore Factory DefaultsModem Initialization Activate DTR Monitoring Activate DCD ManagementSet Computer’s IP Address Select Slip or PPP Select iDEN Packet Wireless Data Mobile IP Authentication Key Mobile IP ActivationMobile IP Home Agent Address Mobile Node IP Prefix Length Mobile IP Security Parameter Index SPI Header Compression Saving AT Settings GPS Default Parameters IR1200 Modem AT Commands General AT CommandsCommand Usage Action User Image Profile Commands Registration, Reset, and Authentication CommandsNetwork Status Commands Command Other Useful AT CommandsCommand Mode Echo Answer Dial Hang-up Request Modem InformationGo Online Quiet Mode Pulse DialingTone Dialing Extended Result Codes Verbose Result Codes DCD Behavior Restore User Defaults Restore Factory Default Command&FDTR Behavior Command&V Command&KLocal Flow Control Traditional Display Current Parameter Value Command+IFC Command&ICFLocal Character Framing Local Flow Control Pcca Local Data Rate DTE Change the DCE’s PIN Lock/Unlock the DCE Packet Data Sleep Timer Command +WS175Command+WV312 Command+WV300 Command+WV301Select Mobile IP Client Mobile IP Session Timer Command +WV302DTE IP Address Command+WV311 Command+WPNEIDTE IP Address Prefix Length Data Encryption Command +WV308 Command +WS45DTE Stack Service Class Packet Data Registration TimeoutWDS Stack Circuit Data Auto-Answer Circuit Data Establishment Timeout Comma Dial Modifier Timer Circuit Data Idle TimerCommandS30 Nextel.com Registers RegistersProgramming the S-Register Reading an S-Register Value Supported S-RegistersRegister # Function Valid value ranges from 0 zero to 255 zero is Default value Command Dial Modifier Time Troubleshooting Common ProblemsSymptom Troubleshooting Tips Modem Message Explanation Error Messages Busy Diagnostic Commands Extended Error Result Codes Extended Error AT Command Packet Data Operation Code General Description Circuit Data Operation Nextel.com Safe and Efficient Operation Guidelines Safety NoticeExposure to Radio Frequency Energy Medical and Personal Electronic Devices Interference with Other Electronic Devices Hearing AidsOther Medical Devices Copyright and Trademark 102nextel.com Appendix a Glossary Configuration Command ModeData Services Default Dial Up Networking DUN Differential GPSFirmware Frequency GPS Antenna Internet Service Provider ISPGPS Processor GPS Receiver Laptops KbpsLocal Area Network LAN Mobile IP Parallel Port Packet of DataParity Bit Protocol System Administrator Service Specific SoftwareRoutable IP Address Public IP Address RS-232 Terminal Mode Transmission RateUTC Offset Circuit data · COM1 · Index 112nextel.com