Nextel comm IR1200 guide

iR1200 Modem

appropriate COM Port (typically COM1)

•Multiple Baudrate should be unchecked

•Baud Rate: 19200 (bps)

The program will check the communication settings and attempt to connect to the modem.

25The Packet Data Configuration window opens. Select No,

I would like to configure my modem later or my modem has already been configured then click Next.

26The Installation Complete window opens. Select Finish on the following screens to complete the installation process.

27The Setup Complete window opens. Click Finish.

34	nextel.com

Image 44

Nextel comm IR1200 manual Multiple Baudrate should be unchecked Baud Rate 19200 bps

Contents

Administrator’s Guide General Page Table of Contents Circuit Switched Data Modem Configuration Windows NT Saving AT Settings GPS Default Parameters Registers Pacemakers Hearing Aids Please Read Safety Notice on Before using the iR1200 Modem Page Table of Figures Table of Figures Nextel.com FCC Compliance Declaration of Conformity IR1200 Modem Description How to OrderRequired Components Online Documentation Using This Guide IntroductionWelcome to Nextel Nextel Coverage Nextel Customer Care Overview General Overview IR1200 Rugged Modem Modem ConfigurationsModem Operating Modes IR1200 GPS-Enabled Modem Rear Panel of iR1200 Rugged Modem Modem Specifications LED External LED IR1200 Modem Connecting the Modem Getting Started Cabling Diagram Fixed Environment Communication Indicators Signal Color Indication CTS Packet Data Status IR1200 Modem Installing iDEN Packet Data Applet Hardware and Installation Requirements Before You Begin Download Software Instructions Windows 95/98/ME Click Next on the iDEN Packet Data Applet Setup screen Computer Program will check the communication settings and attempt Windows NT Click Next on the iDEN Packet Data Applet Setup screen Modem Installation Finish window opens. Click Finish Installing iDEN Packet Data Applet Multiple Baudrate should be unchecked Baud Rate 19200 bps Windows Click Next on the iDEN Packet Data Applet Setup screen That your modem is connected and click Next Multiple Baudrate should be unchecked Baud Rate 19200 bps Verify Dial-Up Networking Setting Up Windows ComponentsClick Cancel to close the Make New Connection window Verify TCP/IP Protocol Installation Click OK to close the Select Network Protocol window Windows NT/2000 Installing the Dial-Up Adapter Settings Select Control Panel Connection wizard. Click Next Install the Modem Manual Modem ConfigurationModem Configuration Windows 95/98/ME Configure the Modem Driver Create a Dial-up Networking Connection Click OK to close the Advanced Connection Settings windowUse Flow Control Hardware RTS/CTS Modem Configuration Windows NT Under Type of Dial-Up Server, select PPP Modem Installation Finish window opens. Click Finish Configure the Modem Driver Wizard Finish window opens. Click Finish Modem Configuration Windows Edit entry and modem properties from the drop-down list Create and Configure a Dial-up Networking Connection Nextel.com Modify Dial-up Connection Parameters IR1200 Modem Modem Profiles and Settings HyperTerminal Setup Connection Description screen appears Bits Per second Data Bits Opening a HyperTerminal Session Parity None Stop Bits Flow Control HardwareWindows 2000/XP/Windows Windows NT Modem Initialization Configuring With AT CommandsRestore Factory Defaults Set Computer’s IP Address Activate DTR MonitoringActivate DCD Management Select iDEN Packet Wireless Data Select Slip or PPP Mobile IP Home Agent Address Mobile IP Authentication KeyMobile IP Activation Mobile IP Security Parameter Index SPI Mobile Node IP Prefix Length Saving AT Settings Header Compression GPS Default Parameters IR1200 Modem Command Usage Action AT CommandsGeneral AT Commands Network Status Commands User Image Profile CommandsRegistration, Reset, and Authentication Commands Other Useful AT Commands CommandCommand Mode Echo Answer Dial Go Online Hang-upRequest Modem Information Tone Dialing Quiet ModePulse Dialing Verbose Result Codes Extended Result Codes Restore User Defaults DCD Behavior DTR Behavior Restore Factory DefaultCommand&F Command&K Command&VLocal Flow Control Traditional Display Current Parameter Value Command&ICF Command+IFCLocal Character Framing Local Flow Control Pcca DTE Local Data Rate Lock/Unlock the DCE Change the DCE’s PIN Command+WV312 Packet Data Sleep TimerCommand +WS175 Select Mobile IP Client Command+WV300Command+WV301 DTE IP Address Mobile IP Session TimerCommand +WV302 Command+WPNEI Command+WV311DTE IP Address Prefix Length Data Encryption DTE Stack Command +WV308Command +WS45 WDS Stack Service ClassPacket Data Registration Timeout Circuit Data Establishment Timeout Circuit Data Auto-Answer CommandS30 Comma Dial Modifier TimerCircuit Data Idle Timer Nextel.com Programming the S-Register RegistersRegisters Register # Function Reading an S-Register ValueSupported S-Registers Valid value ranges from 0 zero to 255 zero is Default value Command Dial Modifier Time Symptom Troubleshooting Tips TroubleshootingCommon Problems Modem Error Messages Message Explanation Diagnostic Commands Busy Extended Error AT Command Extended Error Result Codes Code General Description Packet Data Operation Circuit Data Operation Nextel.com Safety Notice Safe and Efficient Operation GuidelinesExposure to Radio Frequency Energy Medical and Personal Electronic Devices Other Medical Devices Interference with Other Electronic DevicesHearing Aids Copyright and Trademark 102nextel.com Appendix a Glossary Command Mode ConfigurationData Services Default Differential GPS Dial Up Networking DUNFirmware Frequency Internet Service Provider ISP GPS AntennaGPS Processor GPS Receiver Kbps LaptopsLocal Area Network LAN Mobile IP Packet of Data Parallel PortParity Bit Protocol Service Specific Software System AdministratorRoutable IP Address Public IP Address RS-232 UTC Offset Terminal ModeTransmission Rate Index Circuit data · COM1 · 112nextel.com