Manuals / Omega Vehicle Security / Computer Equipment / Network Card

Omega Vehicle Security OM-550 manual Gain Adjust, Tilt Stand

Models: OM-550

1 84

Download 84 pages 19.9 Kb

Page 16

2.1.9 GAIN ADJUST

The Gain Adjust holes are used when performing a Voltage or Temperature calibration procedure. There are two holes located on the bottom of the OM-550 one for adjusting the Volt Gain and another for adjusting the Temp Gain (see APPENDIX A:

CALIBRATION for more information).

2.1.10 TILT STAND

The Tilt Stand to allows the user to get a better view of the Keypad and printed data. Tilt the OM-550 up by rotating the stand downward until it comes to a complete stop and then set the OM-550 on a table or flat surface.

Figure 2-12

OM-550

u11u

Image 16

Omega Vehicle Security OM-550 manual Gain Adjust, Tilt Stand

Contents

Table of Contents Date Time Introduction ∙ The OM-550 Datalogger may be referred to as LoggerOperator Safety Information Product Usage WarningsFor protection of the OM-550 itself, observe the following Unpacking OM-550 Features FeaturesOM-550 features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ PROG/EXIT ∙ Stop∙ OK ∙ Optional Connectors Channel ConnectorsApplication Printer Window To remove the Viewing WindowBattery Cover Thermal PaperDC Jack Serial Data PortGain Adjust Tilt StandPower Supplies Inputs Voltage Transducer InputsProbes Probe SETThermocouple Inputs TypeProgrammed Features Data CacheStatistics LOW Battery Operation POWER-SAVE ModeBattery Check Power Connection Battery InstallationConnecting the AC Power Adapter Connecting the DC Power CablePaper Installation Data Port Connection PIN AdapterProgramming ∙ Programming outline 1. Select ChannelProgramming Keys Print Formatting PositionTemperature Channels Voltage ChannelsMath PSEUDO-CHANNEL This Interval Overrun can be avoided in two ways LOG IntervalNot Printing Operation AT Full Cache Recording Time Temperature Units Rejection FrequencyCalibration Mode To return to Normal modeTadjust Voltage Input Scaling Matching Transducers to the OM-550Matching a Voltage Transducer R1 = 2 R2 = V-2= 2.0000 VDC = R1 Matching a Current TransducerR1 = 2 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Matching and Scaling a Current Transducer ExampleU38u Unit Labels Operation Programmed InformationLog Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u Manual Reset programs the OM-550 as follows Appendix a Calibration ∙ Manual Reset∙ Performing a Manual Reset ∙ Calibration Procedure Setup∙ Voltage Adjustment Procedure ∙ Thermocouple Adjustment Procedure∙ Exiting CAL Mode To return to normal operationVoltage Measurement Inputs Appendix B SpecificationsAccuracy Printer Paper LifeDigital Interface RS-232 ConversionPOWER/CURRENT Requirements Battery LifePhysical Dimensions ConnectorsOM-550 DOS Software Table of Contents How to Use This Manual IntroductionFonts Used in this Manual CPU, RAM, Hardware PrinterSoftware Installation ∙ Hard Drive InstallationStarting the Program To start the programMaster Menu Reading Data from the OM-550 Load Existing LOG Files To load a LOG fileModify Software Configuration U6u List Data on Monitor To list dataPrint Data on Printer Save Text FileTo print data To save data as textEdit Plot Labels To edit a plot labelHOT Plot Status BAR Magnify Tool To Magnify a portion of the Data GraphMagnify MAP Magnified Area Axis Labels Channel Data To select a channel to graphTo link plot lines Channels 4 & 5 After Linking Data Graph ∙ X-Data Cursors ∙ Data Plots∙ X-Cursor Data Table Help Menu To activate the Help menuTo list log files List Existing LOG Files on PrinterTo quit Appendix a KEY Functions