Manuals / Omega Vehicle Security / Computer Equipment / Network Card

Omega Vehicle Security OM-550 manual Table of Contents

Models: OM-550

1 84

Download 84 pages 19.9 Kb

Page 58

TABLE OF CONTENTS
INTRODUCTION	ii
Ÿ How to Use This Manual	ii
Ÿ Terms Used in this Manual	ii
Ÿ Fonts Used in this Manual	iii
Ÿ File Formats	iii
PC Hardware Requirements	iv
Software Installation	v
1.0 STARTING THE PROGRAM	1
2.0 MASTER MENU	2
2.1 READING DATA FROM THE OM-550	3
2.2 LOAD EXISTING LOG FILES	4
2.3 MODIFY SOFTWARE CONFIGURATION	5
2.4 LIST DATA ON MONITOR	7
2.5 PRINT DATA ON PRINTER	8
2.6 SAVE TEXT FILE	8
2.7 EDIT PLOT LABELS	9
2.8 HOT PLOT	10
2.8.1 STATUS BAR	11
2.8.2 MAGNIFY TOOL	12
2.8.3 Y-AXIS LABELS	14
2.8.4 CHANNEL DATA	15
2.8.5 DATA GRAPH	18
2.8.6 HELP MENU	20
2.9 LIST EXISTING LOG FILES ON PRINTER	21
2.10 QUIT	21
APPENDIX A: KEY FUNCTIONS	22

OM-550 DOS Software

♦i ♦

Image 58

Omega Vehicle Security OM-550 manual Table of Contents

Contents

Table of Contents Date Time Introduction ∙ The OM-550 Datalogger may be referred to as LoggerOperator Safety Information Product Usage WarningsFor protection of the OM-550 itself, observe the following Unpacking OM-550 Features FeaturesOM-550 features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ PROG/EXIT ∙ Stop∙ OK ∙ Optional Connectors Channel ConnectorsApplication Printer Window To remove the Viewing WindowDC Jack Battery CoverThermal Paper Serial Data PortGain Adjust Tilt StandPower Supplies Probes InputsVoltage Transducer Inputs Probe SETThermocouple Inputs TypeProgrammed Features Data CacheStatistics LOW Battery Operation POWER-SAVE ModeBattery Check Power Connection Battery InstallationConnecting the AC Power Adapter Connecting the DC Power CablePaper Installation Data Port Connection PIN AdapterProgramming ∙ Programming outline 1. Select ChannelProgramming Keys Print Formatting PositionTemperature Channels Voltage ChannelsMath PSEUDO-CHANNEL This Interval Overrun can be avoided in two ways LOG IntervalNot Printing Operation AT Full Cache Recording Time Temperature Units Rejection FrequencyCalibration Mode To return to Normal modeTadjust Matching a Voltage Transducer Voltage Input ScalingMatching Transducers to the OM-550 R1 = 2 R2 = V-2= 2.0000 VDC = R1 Matching a Current TransducerR1 = 2 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Matching and Scaling a Current Transducer ExampleU38u Unit Labels Operation Programmed InformationLog Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u Manual Reset programs the OM-550 as follows Appendix a Calibration ∙ Manual Reset∙ Performing a Manual Reset ∙ Calibration Procedure Setup∙ Voltage Adjustment Procedure ∙ Thermocouple Adjustment Procedure∙ Exiting CAL Mode To return to normal operationVoltage Measurement Inputs Appendix B SpecificationsAccuracy Digital Interface RS-232 PrinterPaper Life ConversionPhysical Dimensions POWER/CURRENT RequirementsBattery Life ConnectorsOM-550 DOS Software Table of Contents How to Use This Manual IntroductionFonts Used in this Manual CPU, RAM, Hardware PrinterSoftware Installation ∙ Hard Drive InstallationStarting the Program To start the programMaster Menu Reading Data from the OM-550 Load Existing LOG Files To load a LOG fileModify Software Configuration U6u List Data on Monitor To list dataTo print data Print Data on PrinterSave Text File To save data as textEdit Plot Labels To edit a plot labelHOT Plot Status BAR Magnify Tool To Magnify a portion of the Data GraphMagnify MAP Magnified Area Axis Labels Channel Data To select a channel to graphTo link plot lines Channels 4 & 5 After Linking Data Graph ∙ X-Data Cursors ∙ Data Plots∙ X-Cursor Data Table Help Menu To activate the Help menuTo list log files List Existing LOG Files on PrinterTo quit Appendix a KEY Functions