Manuals / Omega Vehicle Security / Computer Equipment / Network Card

Omega Vehicle Security OM-550 manual Paper Installation

Models: OM-550

1 84

Download 84 pages 19.9 Kb

Page 25

3.2PAPER INSTALLATION

1.Unwind several inches of paper from the paper roll.

2.Fold the end of the thermal paper over creating a straight flat edge as shown in Figure 3-2. This creates a strong edge and allows the paper properly center in the printer when inserting it into the rear paper slot.

Paper orientation is very important because only one side is coated for thermal printing.

Figure 3-2

3.Insert the paper into the rear paper slot as shown in Figure 3-2. Turn the OM-

550 “ON”, then press and hold thePAPER“ FEED” key to feed the paper through the printer.

Figure 3-3

4.After the paper appears in the front window, pull several inches through.

5.Test the operation of the printer & paper-feed mechanism by turning the unit “OFF” and back “ON”. When finished examine the printed messages for clarity.

OM-550

u20u

Image 25

Omega Vehicle Security OM-550 manual Paper Installation

Contents

Table of Contents Date Time ∙ The OM-550 Datalogger may be referred to as Logger Introduction Product Usage Warnings Operator Safety Information For protection of the OM-550 itself, observe the following Unpacking OM-550 Features FeaturesOM-550 features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ PROG/EXIT ∙ Stop∙ OK ∙ Optional Connectors Channel ConnectorsApplication To remove the Viewing Window Printer Window Thermal Paper Battery CoverDC Jack Serial Data Port Tilt Stand Gain Adjust Power Supplies Voltage Transducer Inputs InputsProbes Probe SET Type Thermocouple Inputs Data Cache Programmed Features Statistics LOW Battery Operation POWER-SAVE ModeBattery Check Battery Installation Power Connection Connecting the DC Power Cable Connecting the AC Power Adapter Paper Installation PIN Adapter Data Port Connection ∙ Programming outline 1. Select Channel Programming Programming Keys Position Print Formatting Voltage Channels Temperature Channels Math PSEUDO-CHANNEL This Interval Overrun can be avoided in two ways LOG IntervalNot Printing Operation AT Full Cache Recording Time Rejection Frequency Temperature Units To return to Normal mode Calibration Mode Tadjust Matching Transducers to the OM-550 Voltage Input ScalingMatching a Voltage Transducer R1 = 2 R2 = V-2 = 2.0000 VDC = R1 Matching a Current TransducerR1 = 2 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Example Matching and Scaling a Current Transducer U38u Unit Labels Programmed Information Operation Log Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u Manual Reset programs the OM-550 as follows Appendix a Calibration ∙ Manual Reset∙ Performing a Manual Reset Setup ∙ Calibration Procedure ∙ Thermocouple Adjustment Procedure ∙ Voltage Adjustment Procedure To return to normal operation ∙ Exiting CAL Mode Voltage Measurement Inputs Appendix B SpecificationsAccuracy Paper Life PrinterDigital Interface RS-232 Conversion Battery Life POWER/CURRENT RequirementsPhysical Dimensions Connectors OM-550 DOS Software Table of Contents Introduction How to Use This Manual Fonts Used in this Manual Printer CPU, RAM, Hardware ∙ Hard Drive Installation Software Installation To start the program Starting the Program Master Menu Reading Data from the OM-550 To load a LOG file Load Existing LOG Files Modify Software Configuration U6u To list data List Data on Monitor Save Text File Print Data on PrinterTo print data To save data as text To edit a plot label Edit Plot Labels HOT Plot Status BAR To Magnify a portion of the Data Graph Magnify Tool Magnify MAP Magnified Area Axis Labels To select a channel to graph Channel Data To link plot lines Channels 4 & 5 After Linking Data Graph ∙ X-Data Cursors ∙ Data Plots∙ X-Cursor Data Table To activate the Help menu Help Menu To list log files List Existing LOG Files on PrinterTo quit Appendix a KEY Functions