List Existing LOG Files on Printer | Omega Vehicle Security OM-550

2.9 LIST EXISTING LOG FILES ON PRINTER

Option #9 List Existing Log Files on Printer, on the Master Menu prints the saved LOG files to the printer. Set the printer up using Option #3 Modify Software Configure.

To list log files:

1.Press the key, and the printing process will start. When it is finished spooling the program will automatically return to the Master Menu.

2.10QUIT

Option #10 Quit, on the Master menu quits the software program.

To quit:

1.Press , if the data has not been saved the software program will prompt the user to save it. If you want to save press “Y” for Yes and “N” for no.

OM-550 DOS Software

u21u

Image 83

Omega Vehicle Security OM-550 manual List Existing LOG Files on Printer, To list log files, To quit

Contents

Table of Contents Date Time ∙ The OM-550 Datalogger may be referred to as Logger Introduction Product Usage Warnings Operator Safety Information For protection of the OM-550 itself, observe the following Unpacking OM-550 features FeaturesOM-550 Features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ OK ∙ Stop∙ PROG/EXIT Application Channel Connectors∙ Optional Connectors To remove the Viewing Window Printer Window Serial Data Port Battery CoverThermal Paper DC Jack Tilt Stand Gain Adjust Power Supplies Probe SET InputsVoltage Transducer Inputs Probes Type Thermocouple Inputs Data Cache Programmed Features Statistics Battery Check POWER-SAVE ModeLOW Battery Operation Battery Installation Power Connection Connecting the DC Power Cable Connecting the AC Power Adapter Paper Installation PIN Adapter Data Port Connection ∙ Programming outline 1. Select Channel Programming Programming Keys Position Print Formatting Voltage Channels Temperature Channels Math PSEUDO-CHANNEL Not Printing LOG IntervalThis Interval Overrun can be avoided in two ways Operation AT Full Cache Recording Time Rejection Frequency Temperature Units To return to Normal mode Calibration Mode Tadjust R1 = 2 R2 = V-2 Voltage Input ScalingMatching Transducers to the OM-550 Matching a Voltage Transducer R1 = 2 Matching a Current Transducer= 2.0000 VDC = R1 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Example Matching and Scaling a Current Transducer U38u Unit Labels Programmed Information Operation Log Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u ∙ Performing a Manual Reset Appendix a Calibration ∙ Manual ResetManual Reset programs the OM-550 as follows Setup ∙ Calibration Procedure ∙ Thermocouple Adjustment Procedure ∙ Voltage Adjustment Procedure To return to normal operation ∙ Exiting CAL Mode Accuracy Appendix B SpecificationsVoltage Measurement Inputs Conversion PrinterPaper Life Digital Interface RS-232 Connectors POWER/CURRENT RequirementsBattery Life Physical Dimensions OM-550 DOS Software Table of Contents Introduction How to Use This Manual Fonts Used in this Manual Printer CPU, RAM, Hardware ∙ Hard Drive Installation Software Installation To start the program Starting the Program Master Menu Reading Data from the OM-550 To load a LOG file Load Existing LOG Files Modify Software Configuration U6u To list data List Data on Monitor To save data as text Print Data on PrinterSave Text File To print data To edit a plot label Edit Plot Labels HOT Plot Status BAR To Magnify a portion of the Data Graph Magnify Tool Magnify MAP Magnified Area Axis Labels To select a channel to graph Channel Data To link plot lines Channels 4 & 5 After Linking Data Graph ∙ X-Cursor Data Table ∙ Data Plots∙ X-Data Cursors To activate the Help menu Help Menu To quit List Existing LOG Files on PrinterTo list log files Appendix a KEY Functions