Software Installation | Omega Vehicle Security OM-550 specification

Software Installation

The software is on a 3.5” floppy disk and before it is installed on a PC, make a backup copy of the program disk, you should never work from your original program disks. Be sure to view the README file on the program disk before installing the software (any standard text viewer can be used). The README contains the latest information on the software and installation instructions.

∙HARD DRIVE INSTALLATION

1.Insert disk 1 in the disk drive.

2.At the DOS prompt, type the drive name, colon, backslash and instalit and hit the [enter] key.

For example, if the program diskette is inserted into the “A” drive; type:A:\instalit.

3. Follow the setup instructions provided with the software.

OM-550 DOS Software

♦v ♦

Image 62

Omega Vehicle Security OM-550 manual Software Installation, ∙ Hard Drive Installation

Contents

Table of Contents Date Time Introduction ∙ The OM-550 Datalogger may be referred to as Logger Operator Safety Information Product Usage Warnings For protection of the OM-550 itself, observe the following Unpacking OM-550 features FeaturesOM-550 Features Activity LED & Horn Keypad ∙ ON-OFF ∙ RUN ∙ OK ∙ Stop∙ PROG/EXIT Application Channel Connectors∙ Optional Connectors Printer Window To remove the Viewing Window DC Jack Battery CoverThermal Paper Serial Data Port Gain Adjust Tilt Stand Power Supplies Probes InputsVoltage Transducer Inputs Probe SET Thermocouple Inputs Type Programmed Features Data Cache Statistics Battery Check POWER-SAVE ModeLOW Battery Operation Power Connection Battery Installation Connecting the AC Power Adapter Connecting the DC Power Cable Paper Installation Data Port Connection PIN Adapter Programming ∙ Programming outline 1. Select Channel Programming Keys Print Formatting Position Temperature Channels Voltage Channels Math PSEUDO-CHANNEL Not Printing LOG IntervalThis Interval Overrun can be avoided in two ways Operation AT Full Cache Recording Time Temperature Units Rejection Frequency Calibration Mode To return to Normal mode Tadjust Matching a Voltage Transducer Voltage Input ScalingMatching Transducers to the OM-550 R1 = 2 R2 = V-2 R1 = 2 Matching a Current Transducer= 2.0000 VDC = R1 Data Scaling mX + b calculation Matching and Scaling a Voltage Transducer VDC Matching and Scaling a Current Transducer Example U38u Unit Labels Operation Programmed Information Log Interval Time Temperature Units Enter a Tadjust value, or press OK to finish programming U44u ∙ Performing a Manual Reset Appendix a Calibration ∙ Manual ResetManual Reset programs the OM-550 as follows ∙ Calibration Procedure Setup ∙ Voltage Adjustment Procedure ∙ Thermocouple Adjustment Procedure ∙ Exiting CAL Mode To return to normal operation Accuracy Appendix B SpecificationsVoltage Measurement Inputs Digital Interface RS-232 PrinterPaper Life Conversion Physical Dimensions POWER/CURRENT RequirementsBattery Life Connectors OM-550 DOS Software Table of Contents How to Use This Manual Introduction Fonts Used in this Manual CPU, RAM, Hardware Printer Software Installation ∙ Hard Drive Installation Starting the Program To start the program Master Menu Reading Data from the OM-550 Load Existing LOG Files To load a LOG file Modify Software Configuration U6u List Data on Monitor To list data To print data Print Data on PrinterSave Text File To save data as text Edit Plot Labels To edit a plot label HOT Plot Status BAR Magnify Tool To Magnify a portion of the Data Graph Magnify MAP Magnified Area Axis Labels Channel Data To select a channel to graph To link plot lines Channels 4 & 5 After Linking Data Graph ∙ X-Cursor Data Table ∙ Data Plots∙ X-Data Cursors Help Menu To activate the Help menu To quit List Existing LOG Files on PrinterTo list log files Appendix a KEY Functions