Onkyo 29400021 Sirius antenna TX-NR807 North American models, Monitor OUT, Component Video in 1

Front & Rear Panels—Continued

gSIRIUS antenna

(TX-NR807: North American models)

This jack is for connecting a SIRIUS Satellite Radio antenna, sold separately (see the separate SIRIUS instructions).

hMONITOR OUT

These S-Video and composite video jacks should be connected to a video input on your TV or projector.

iHDMI IN 1–6 and OUT (TX-NR807) HDMI IN 1–5 and OUT (HT-RC180)

HDMI (High Definition Multimedia Interface) con- nections carry digital audio and digital video.

The HDMI inputs are for connecting components with an HDMI output, such as a DVD player, Blu- ray Disc Player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “HDMI Input Setup” on page 48. The HDMI output is for connecting a TV or projec- tor with an HDMI input.

jCOMPONENT VIDEO IN 1 and 2

These RCA component video inputs are for con- necting components with a component video out- put, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Component Video Setup” on page 49.

kCOMPONENT VIDEO MONITOR OUT

These RCA component video outputs are for con- necting a TV or projector with a component video input.

lFM ANTENNA

This jack is for connecting an FM antenna.

AM ANTENNA

These push terminals are for connecting an AM antenna.

mIR IN/OUT (TX-NR807)

A commercially available IR receiver can be con- nected to the IR IN jack, allowing you to control the AV receiver while you’re in Zone 2/3, or control it when it’s out of sight, for example, installed in a cabinet.

A commercially available IR emitter can be con- nected to the IR OUT jack to pass IR (infrared) remote control signals through to other components.

n12V TRIGGER OUT ZONE 2 (TX-NR807)

This output can be connected to the 12-volt trigger input on a component in Zone 2. When Zone 2 is turned on, a 12-volt trigger signal is output.

12V TRIGGER OUT ZONE 3 (TX-NR807)

This output can be connected to the 12-volt trigger input on a component in Zone 3. When Zone 3 is turned on, a 12-volt trigger signal is output.

oAC INLET

The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet.

pGND screw

This screw is for connecting a turntable’s ground wire.

qPHONO IN

These analog audio inputs are for connecting a turn- table.

rCD IN

These analog audio inputs are for connecting a CD player’s analog audio output.

sTV/TAPE IN/OUT

These analog audio inputs and outputs are for con- necting a TV or recorder with an analog audio input and output (cassette, Mini Disc, etc.).

tGAME IN

Here you can connect a game console, etc. Input jacks include S-Video, composite video, and analog audio.

uCBL/SAT IN

Here you can connect a cable/satellite receiver, set- top box, etc. Input jacks include S-Video, composite video, and analog audio.

vVCR/DVR IN/OUT

Here you can connect a VCR or DVR (digital video recorder). Input and output jacks include S-Video, composite video, and analog audio.

wDVD/BD IN

Here you can connect a DVD/BD player. Input jacks include S-Video, composite video, and analog audio. You can connect a DVD/BD player’s 2-chan- nel analog audio output.

xPRE OUT: FRONT L/R, CENTER, SURR L/R, and SURR BACK L/R

These multichannel analog audio outputs can be connected to the analog audio input on a multichan- nel power amplifier for when you want to use the AV receiver solely as a preamplifier.

yPRE OUT: SUBWOOFER

These analog audio outputs can be connected to a powered subwoofer. You can connect the powered subwoofer with two PREOUT: SUBWOOFER jacks respectively. The same signal is output from each jack.

zPRE OUT: ZONE 2, ZONE 3 L/R

These analog audio outputs can be connected to the line inputs on amplifiers in Zone 2 and Zone 3.

12