Panasonic AJ-HPX3100G 7. Recording Error, 5. Image Sequence Error, 10. Battery Nearly Empty, 8. Number of Clips Exceeded, 6. Corruption of Standard Signal

5. Image Sequence Error

Display window	“E-40” appears in the time code display field.
indication
WARNING lamp	Blinks 4 times per second.
Tally lamp	Blinks 4 times per second while recording
	continues.
Viewfinder	The REC WARNING indicator lights up.
Warning tone	Beeps 4 times per second.
Warning	There are abnormal conditions in the image
description	sequence of the 24P, 30P, or 25P mode.
Recording/	Images can be recorded and played back,
playback	but some frames may be dropped or the
operation	sequences of TC and UB may shift.
	Confirm the recording/playback operation
	after turning OFF the power supply once and
Countermeasures	then turning it on again. If the error is not
	corrected after executing this procedure,
	contact the dealer.

6. Corruption of Standard Signal

Display window	“E-40” appears in the time code display field.
indication
WARNING lamp	Blinks 4 times per second.
Tally lamp	Blinks 4 times per second.
Viewfinder	The TEMPORARY PAUSE indicator lights up.
Warning tone	Beeps 4 times per second while recording
	continues.
	Corruption in the input signals from the
Warning	standard GENLOCK IN and SDI IN
	connectors means correct recording is not
description
	possible, and this has stopped. The clip will
	be divided.
Recording/	When the signal returns to normal, recording
	will automatically start again. However, this
playback
	will not automatically start when in
operation
	INTERVAL REC mode or LOOP REC mode.
	Please check the input signal from the
Countermeasures	GENLOCK IN connector or SDI IN connector.
	If errors continue, please contact your dealer.

7. Recording Error

Display window	“00:00:00:11” appears in the time code display
	field. Even after recording is stopped, this
indication	display continues to blink until the next
	operation is performed.
WARNING lamp	Blinks 4 times per second while recording
	continues.
Tally lamp	Blinks 4 times per second while recording
	continues.
Viewfinder	The REC WARNING indicator lights up.
Warning tone	Beeps 4 times per second while recording
	continues.
Warning	This indicates a failure either in the P2 card
description	recording or the recording circuit.
Recording/
playback	The recording may stop or continue.
operation
	Restart recording. Or, turn the power OFF and
Countermeasures	turn it ON again, before starting recording. If
	the recording cannot be performed normally,
	change the P2 card.

8. Number of Clips Exceeded

Display window	“00:00:00:11” appears in the time code display
	field. Even after recording is stopped, this
indication	display continues to blink until the next
	operation is performed.
WARNING lamp	Blinks 4 times per second while recording
	continues.
Tally lamp	Blinks 4 times per second while recording
	continues.
Viewfinder	The OVER MAX# CLIPS indicator lights up.
Warning tone	Beeps 4 times per second while recording
	continues.
Warning	This is displayed when attempting to record
	clips where the total quantity exceeds the
description
	upper limit (1000 pieces) for a single P2 card.
Recording/
playback	Cannot record. Stops while recording.
operation
Countermeasures	Insert a new P2 card or delete the unwanted
	clips in the P2 card.

9. Low Wireless Signal Reception

Display window	No display.
indication
WARNING lamp	Blinks 4 times per second. (During pause and
	recording)
Tally lamp	Blinks 4 times per second while recording
	continues.
Viewfinder	The WIRELESS RF indicator lights up while
	recording continues.
Warning tone	Beeps 4 times per second while recording
	continues.
Warning	This error indicates poor wireless audio
description	reception conditions.
Recording/	Continues to operate without receiving the
playback
	wireless microphone signal.
operation
Countermeasures	Check the microphone power supply and the
	reception status of the wireless receiver.

10. Battery Nearly Empty

Display window	One of the bars in the battery remaining
indication	indicator starts blinking.
WARNING lamp	Blinks once per second.
Tally lamp	Blinks once per second.
Viewfinder	The BATT LED blinks.
Warning tone	Beeps 4 times per second.
Warning	The battery is about to run out.
description
Recording/
playback	Continues to operate.
operation
Countermeasures	Replace the battery as required.

154 Maintenance and Inspections: Warning System