Panasonic AJ-HPX3100G 157

Item	Message	Description	Measure

	CANNOT ACCESS	An error occurred during P2 card access.	Check P2 card.
	CARD!

	CANNOT ACCESS	An error occurred during hard disk access.	Check hard disk status and connection.
	TARGET!

	CANNOT FORMAT!	The hard disk cannot be initialized.	Connect another hard disk drive.

	CANNOT	The destination target cannot be properly	Reboot the hard disk or connect a different hard
	RECOGNIZE	recognized.	disk.
	HDD!

	CARD IS EMPTY!	The P2 selected for copying is empty.	Copying is not performed since the card is empty.
	CANNOT COPY!

	FORMAT P2 CARD!	This warning indicates that data could not be	You cannot copy to a P2 card that contains data.
		imported from a hard disk to a P2 card	Format the card on a P2 device and copy again.
		because the P2 card contained recorded data.
HDD
HDD	HDD CAPACITY	Not enough space left on the hard disk.	There is not enough space on the connected hard
(USB HOST	FULL!		disk. Use a new hard disk or formatted hard disk.
MODE)
	HDD	The unit is not connected to a hard disk.	Reconnect the USB cable. If the hard disk does not


	DISCONNECTED!		operate normally, turn it off and turn it back on
	DISCONNECTED!		operate normally, turn it off and turn it back on
			again.		Maintenance

	TOO MANY	There are too many partitions.	Hard disks can handle up to 23 partitions. Use a
	MISMATCH	Copying is not possible since the model	Use a P2 card with the same model number or
	COMPONENT!	number of the destination card does not match	import video in clip units.
		that of the source card.
	PARTITIONS!		new hard disk or formatted hard disk.		and

	TOO MANY	Multiple devices are connected.	Disconnect devices, turn off the unit and turn it back
	TOO MANY	Multiple devices are connected.	Disconnect devices, turn off the unit and turn it back		Inspections
	TARGETS!		on again.		Inspections
	TARGETS!		on again.

	UNKNOWN DEVICE	The connected DVD drive is not compatible.	Disconnect devices, turn off the unit and turn it back
	CONNECTED!		on again.

	VERIFICATION	The compare check after copying failed.	Copy the data again.
	FAILED!

Maintenance and Inspections: Warning System 157

Contents

Operating Instructions Read this first Declaration of Conformity Caution regarding laser beams PLEASE NOTE: What to remember when throwing memory cards away or transferring them to others Precautions when installing USB drivers Contents General Parts and their Functions Recording and Playback Adjustments and Settings for Recording Preparation Manipulating Clips with Thumbnails Connection with external device Maintenance and Inspections Menu Index General Features of Camera unit _2-disk 4-typeconfiguration optical filters Features of Recorder/player unit _Text Memos & Shot Marks _Front-mountedSound Level Control Mechanism _Support for Built-inUnislot Wireless Receiver _Recording Review Capability _Built-inTime Code Generator/reader Features of the Input/Output unit Other features Dimensions drawing Color TV Standard Settings (Settings for frame frequency) System Configuration Parts and their Functions Power Supply and Accessory Mounting Section 12.VF connector (20 Pin) 13.GPS connector 14.Shoulder strap fittings Functions their and Parts Audio (input) Function Section 7.Microphone input +48V ON/OFF switch +48V: 8.Wireless slot 9.F.AUDIO LEVEL (audio recording level adjustment) control Audio (output) Function Section Shooting and Recording/Playback Functions Section 1.CC FILTER/ND FILTER (filter switching) controls CC FILTER knob (outside, large diameter) ND FILTER knob (inside, small diameter) 3.SHUTTER switch 5.SYNCHRO SCAN ADJUSTMENT buttons 6.REC button 7.SHOT MARKER button 8.Text memo button 9.MON OUT CHARACTER switch 17.BUSY (operation mode display) lamp 18.Focal plane index ( ) 19.MARKER SEL, MODE CHK / MENU CANCEL switch 20.Gain selector switch 21.OUTPUT/AUTO KNEE selector switch 23.GENLOCK IN connector 24.SDI IN connector 25.SDI OUT connector 26.MON OUT (monitor output) connector 27.REC button Menu Operation Section Time Code Section Warning and Status Display Functions Display Window Functions LCD Monitor Viewfinder 9.Eyepiece 10.Diopter adjustment ring 11.Connecting plug 12.Locking ring 13.Microphone holder Recording and Playback P2 Cards Removing P2 Cards 1 Open the card slot cover 2 Raise the EJECT button 3 Then, depress the EJECT button to release the P2 card so that you can remove it How to handle data recorded on P2 cards Basic Procedures 2 When the white balance is saved: Normal Recording Normal Recording and Native Recording PRE-RECORDINGfunction Loop Recording Interval Recording Shooting procedures when INTERVAL REC is ON 3 Press REC button To stop recording For continuous recording To stop the Interval recording mode Shooting procedures for the ONE SHOT mode of INTERVAL REC 2 Press the REC button 3 Press the STOP button To divide clips or to change the P2 card used for recording ONE CLIP REC Function Precautions when in ONE CLIP REC mode Recording Review Function Normal and Variable Speed Playback Text Memo Function Shot Mark Function Recording Setting and Operation Mode Multi Format Video system and Recording format Selecting a recording signal and method Recording formats and output connector signal formats Adjusting the White Balance Detection area for the white balance When you have no time to adjust the white balance When the white balance has not been automatically adjusted Retaining white balances On settings for Auto-trackingwhite balance (ATW) Setting Color Temperature Manually Adjusting the Black Balance Setting the Electronic Shutter Shutter Modes Setting the Shutter Mode and Speed Placing the Camera-recorderin SYNCHRO SCAN Mode Assigning Functions to USER Buttons Setting the Switchover of USER SW GAIN Selecting Audio Input Signals and Adjusting Recording Levels Selecting Audio Input Signals Recording level adjustment Adjustment with AUDIO LEVEL CH1/3 / CH2/4 knobs Adjustment with the F.AUDIO LEVEL control W.L.: ALL: When the level adjustment knobs are assigned to CH3/4 Level adjustment of channel1/2 Selection table of adjustment methods Setting External Reference Signal and GENLOCK Locking video signal to external reference signal Setting Time Data Description of time data Recording time code and user bits Setting of the User bits Frame rate information Frame rate: 24P Over 60i (2:3) Frame rate: 24PA Over 60i (2:3:3:2) Frame rate: 30P Over 60i (2:2) 25P Over 50i (2:2) Setting the Internal Clock’s Date and Time Setting the Time Code Externally Locking the Time Code Example 3: Example 4: Example 5: Example 6: Turn on the POWER switch To externally lock the time code 2 Position the TCG switch at [F-RUN] 4 Set the menu option GENLOCK to “GL IN” or “SDI IN” Setting the user bits when the time code is externally locked To unlock the externally locked time code Providing an ID to the Camera Setting UMID Information CTL Count Setting and Display Viewfinder Screen Status Displays Lamps in the Viewfinder Screen Mode Check Screen Displays (MODE CHK function) Selecting Viewfinder Display Information Viewfinder Status Indication Layout Information Item Indication Status Page Page Page Page Displays in mode check only P2 Card Remaining Free Space/capacity Indication Indications Available in the Viewfinder Screen Display Modes and Setting Changes/adjustment Result Messages Setting the Marker Displays Marker Check Screen Displays (MARKER SELECT button function) Checking Return Video Signal in the Viewfinder Adjusting and setting the LCD monitor Selection of video output signals Settings of signals output from SDI OUT connector Settings of signals output from MON OUT connector Handling data Handling SD memory cards Formatting, Writing and Reading an SD memory card To format an SD memory card 4 To exit the menu, press the MENU button 1 Navigate the menu to the <SD CARD READ/ WRITE> screen 2 Turn the JOG dial button to move the cursor to the menu option CARD CONFIG 3 Press the JOG dial button 5 Press the JOG dial button 6 Turn the JOG dial button until a desired character appears To write data on a selected file 9 When the title is set, turn the JOG dial button to move the cursor to [:] 10 Press the JOG dial button to return the cursor to the option TITLE: To read data on an SD memory card To read data on a selected file 4 Turn the JOG dial button to move the cursor to the option READ 7 To exit the menu, press the MENU button How to Use the User Data How to Use Scene File Data Navigate the menu to the <SCENE> screen To read settings data for scene files 2 Turn the JOG dial button to move the cursor to the option SCENE SEL 5 Turn the JOG dial button to move the cursor to the READ option To return data for scene files to their defaults 5 Turn the JOG dial button to move the cursor to the option RESET Page Resetting Menu Option Settings to Defaults Lens file How to provide lens files To save the lens file into the built-inmemory To read the lens file from the builtin memory To write in and read out the lens file to/from the SD memory card Loading lens files from the SD memory card Chromatic Aberration Compensation (CAC) To read the CAC FILE from an SD memory card 7 Select YES using the JOG dial button and then 1 Insert the SD memory card with the CAC FILE press the JOG dial button downloaded from our support website To delete the CAC FILE from the unit 1 Open <CAC ADJ> from the MAINTENANCE page using the menu operation 2 Select “OFF” in CAC CONTROL 4 Press the JOG dial button to fix the selected operation To delete the CAC FILE from the SD memory card When CAC FILE does not operate properly ◆ Notes Preparation Power Supply Mounting the Battery and Setting the Battery Type Use of the external DC power supply and White Shading Adjustments Set the ZEBRA switch on the viewfinder to ON Repeat step If the extender is attached to the lens, release the extender function Attach the lens to the camera Adjusting the Lens White Shading 6 Shoot a white sheet of paper with no unevenness of color 2Use the AUTO W/B BAL switch to adjust the black balance automatically (ABB) Page Preparing for Audio Input When Using the Front Microphone When Using a Wireless Receiver When Using Audio Devices Mounting the Camera on a Tripod Attaching the Shoulder Strap Attaching the Rain Cover Attaching the F.AUDIO LEVEL control Knob Connection of the DC OUT connector and the external REC strat/stop switch Thumbnail Manipulations Overview Thumbnail Screen 8.Clip Number 9.Defective Clip Indicator and Unknown Clip indicator 10.Incomplete Clip Indicator 11.Shot Mark Indicator Selecting Thumbnails Playing back Clips Switching the Thumbnail Display Changing Thumbnails Shot Mark Text Memo Deleting a text memo 2 Move the pointer to the desired text memo, and then press the SET button Using a text memo to break a clip and copy the necessary portion 3 Press the THUMBNAIL MENU button to select OPERATION > COPY Deleting Clips SET button to select the clip Restoring Clips Reconnection of Incomplete Clips Copying Clips Setting of Clip Meta Data THUMBNAIL: Checking and modifying read metadata 3 Use the cursor buttons to move the pointer. Then, press the SET button To set whether or not the uploaded metadata is recorded Selecting the USER CLIP NAME recording method Clear the uploaded metadata Formatting a P2 Card Formatting SD memory cards Setting the Thumbnail Display Mode Properties _P2 Card Status Display Settings When “USED” is selected: 2.P2 Card Status (used memory capacity) 3.P2 Card memory capacity/Total Capacity 4.Total used memory capacity for all slots SD memory card Status Display SD STANDARD: BLANK: TOTAL: NUMBER OF CLIPS: Connection with external device Connection with a PC in the USB DEVICE mode USB HOST mode Switching to the USB HOST mode Using the USB HOST mode 2.VENDOR 3.MODEL 4.SIZE 5.USED 6.FREE CAP 8.MODEL 9.DATE/TIME 10.SERIAL 11.VERIFY 12.NAME Writing data on a hard disk drive 2 Connect a hard disk drive via USB 3 Insert a P2 card 4 Press the THUMBNAIL button 6 Select YES Direction for using a hard disk drive Connection using the SDI IN connector Connection of the remote control unit (AJ-RC10G) Menu option GAMMA menu WHITE menu KNEE menu SHUTTER menu Connection of the extension control unit (AG-EC4G) Maintenance and Inspections Inspections Before Shooting Preparing for Inspections Inspecting the Camera Unit Inspecting the Memory Recording Functions Maintenance Cleaning Inside the Viewfinder Phenomenon Inherent to CCD Cameras Replacing the Backup Battery Connector Signals REMOTE ‹Caution LENS GPS Unislot LIGHT Warning System Warning Description Tables 5. Image Sequence Error 6. Corruption of Standard Signal 7. Recording Error 8. Number of Clips Exceeded 9. Low Wireless Signal Reception Error Codes Card Warning Code Warning and Error Display for Thumbnail Operation and USB HOST MODE Page Menu Menu Configuration Page Setting Menu Options Selecting Options for USER MENU Menu Description Tables SYSTEM SETTING OPTION MODE REC FUNCTION OUTPUT SEL SDI OUT MARKER MON OUT MARKER DOWNCON SETTING LCD MONITOR GENLOCK PAINT MATRIX COLOR CORRECTION LOW SETTING MID SETTING HIGH SETTING ADDITIONAL DTL SKIN TONE DTL KNEE/LEVEL GAMMA „CAMERA SETTING VF DISPLAY ZEBRA Pattern Display VF MARKER VF USER BOX VF INDICATOR (1/3) VF INDICATOR (2/3) VF INDICATOR (3/3) MODE CHECK IND !LED CAM OPERATION SHUTTER SELECT USER SW SW MODE WHITE BALANCE MODE USER SW GAIN LENS/IRIS MAIN OPERATION BATTERY SETTING (1/2) BATTERY SETTING (2/2) MIC/AUDIO (1/3) MIC/AUDIO (2/3) MIC/AUDIO (3/3) TC/UB UMID SET/INFO FILE CAC FILE CARD READ FILE READ screen LENS FILE LENS FILE CARD R/W SCENE INITIALIZE MAINTENANCE CAC ADJ DIAGNOSTIC (1/3) DIAGNOSTIC (2/3) DIAGNOSTIC (3/3) HOURS METER OPTION MENU Updating the Firmware incorporated into the unit Specifications Memory Card Unit Digital Video System Digital Audio System Input/output Unit Accessories Information on software for this product Index Index Page Page (PKL)