Panasonic AJ-HPX3100G manual 80

Information Item			Indication		Status
13. System information	SYSTEM ERROR-¢¢				Something abnormal is happening to the internal computer communications or
and warnings					reference signal. No further recording or playback can be performed. ¢¢ is
					replaced with an error code. For more information, see [Error Codes] (page 155).
	TURN POWER OFF				P2 card has been removed while being accessed (recorded, played back, or
	CARD ERR ¢				formatted), and subsequent operation is disabled.
					An error has occurred while recording data to or playing data from a P2 card.
					In the actual indication the ¢ is replaced by the slot number of the P2 card that
	REC WARNING				triggered the error.
					Something abnormal is happening to video and/or audio being recorded.
	OVER MAX# CLIPS				Displayed when the maximum number of clips (1000) recorded to the P2 card
	TEMPORARY PAUSE				is exceeded.
					There is a temporary halt in recording due to distortion in reference signals
	BACKUP BATT EMPTY				such as during GENLOCK input.
					Backup battery needs replacing.
	FAN STOP				The fan is locked and halted.
	WIRELESS-RF				RF signal from the wireless receiver is degraded.
	EOM				P2 card has no free space.
	BOS				Playback position is at the start of all the clips.
	EOS				Playback position is at the end of all the clips.
	CANNOT REC				The P2 card is not recordable. Detailed information is provided on the
					FUNCTION screen of MODE CHECK.
	CANNOT PLAY				> [Displays in mode check only] (page 82)
					Clip cannot be played back perhaps because no P2 card is loaded, or the P2
	COMM ERROR				card contains no clips.
					Displayed when disconnection between microcomputers continues for a
	TEXT MEMO				specified period or longer.
					Text memo has been added.
	TEXT MEMO INVALID				Text memo has not been successfully added.
	MARK ON/OFF				Shot mark been added or deleted. For information on shot marks, see [Shot
	SHOT MARK INVALID				Mark Function] (page 46).
					This is displayed when shot marks cannot be added.
	UPDATING				Clip information is being updated. Playback operation disabled.
	USB DEVICE				AJ-HPX3100 is in USB DEVICE mode. When communication is disabled, the
	USB HOST				indication blinks.
					Indicates that the camera-recorder is set to the USB HOST mode. When the
	THUMBNAIL OPEN				external hard disk is not successfully recognized, then the indication blinks.
					Thumbnail is being manipulated.
	CLIP DISCONTINUED				Displayed when the consistency of the combined clip is disrupted and
					subsequent recordings cannot be combined in the clip when recording in ONE
	TC REGEN				CLIP REC mode.
					The RET button was pressed to regenerate the time code as the time code for
	SLOT SELECT				the last clip recorded on a P2 card.
					This blinks while the recording slots of P2 cards are switched after pressing
					the USER switch where the SLOT SEL function is assigned.
	SLOT SELECT INVALID				This is displayed if the recording slots of P2 cards cannot be switched when
					the USER switch where the SLOT SEL function is assigned is pressed.
	DIR NG CARD				This is displayed when the recording starts or completes while a P2 card with
		SLOT1/2			an irregular directory arrangement is inserted or data are recorded after
					inserting an irregular P2 card.
	RUN DOWN CARD				This is displayed when the recording starts or completes with a P2 card on
		SLOT1/2			which the maximum number of overwrites has been exceeded, or when data
	REAR XR AUTO				is recorded after inserting such a P2 card.
					The AUDIO IN switch is disabled because audio input automatically goes to
					the rear XLR connector.
14. Time code indication	TCG			12:59:59:20	TCG (time code generator value)
	TCR			12:59:59:20	TCR (time code reader value)
	(V)UBG			AB CD EF 00	UBG VUBG (User bits generator value)
	(V)UBR			12 34 56 78	UBR VUBR (User bits reader value)
	CTL			–1:59:59:20	Displays CTL count.
15. Chromatic aberration	CAC				Displayed when chromatic aberration compensation is activated
compensation
16. Extender	EX				Lens extender used.
17. Color temperature	¢.¢K				Color temperature assigned to A, B, and PRST of the WHITE BAL switch (this
					is a value stored at AWB performance or a value set through the menu
					option). The indication is not provided in ATW mode.
18. Filter position	1 - 4				This indicates the position of the ND filter.
	A - D				This indicates the position of the CC filter.
			(blink)		This indicates that the filter has not been set to a proper position.
19. Dynamic range	DRS				This appears when the video level of a part with high brightness is
stretcher mode					compressed, and the function stretching the dynamic range is selected.

80 Adjustments and Settings for Recording : Viewfinder Screen Status Displays