Panasonic HD1700pe Eject Lamp, SP Mode, KEY Beep, Low, High, Alarm Beep, Audio Unity, Casstt, Rev

Setup menus

<OPERATION> (continued)

No./Item		Description of setting
116	For selecting whether the EJECT lamp is to remain
	lighted or go off after the cassette tape has been
EJECT LAMP	ejected.
	0000	MODE1:
	The EJECT lamp remains lighted.
	0001	MODE2:
	The EJECT lamp goes off.
118*1	For selecting whether to allow or inhibit
	recording on a tape which has been written
SP MODE	by a format other than DVCPRO HD-LP.
INH	0000	OFF:
	Recording on the cassette tape is allowed.
	0001	ON:
	Recording on the cassette tape is inhibited.
	<Notes>
	• When 0 (OFF) has been selected, whether recording
	on the cassette tape is allowed or inhibited is
	determined by the setup menu item No.113 (REC
	INH) setting.
	• The recording format is determined by the setup
	menu item No.020 (SYS FORMAT) setting.
131	For selecting what cue point operation is to
	be performed when the multi cue function has
PAGE MODE	been set to ON.
	0000	MANU:
	Operation is confined within the selected page,
	and 6 cue points can be registered.
	0001	AUTO:
	When the page whose cue points are being
	registered becomes full, operation is
	automatically transferred to the next page, and
	registration is continued. A total of 60 cue
	points on up to 10 pages can be registered.
132	For selecting whether to perform the
	registration operation if all the cue points
ROTA MODE	have already been registered when the multi
	cue function has been set to ON.
	0000	OFF:
	No further cue points are registered.
	0001	ON:
	The registration operation is continued. If “MANU”
	has been selected as the setup menu item No.131
	(PAGE MODE) setting, the next cue point is
	registered at CUE¢1 on the page concerned; if
	“AUTO” has been selected, it is registered at CUE01.
133	For setting the volume of the sound heard
	when the keys are touched.
KEY BEEP	0000	OFF
	0001	LOW
	0002	HIGH
134	For setting the volume of the alarm tone.
	0000	OFF
ALARM BEEP	0001	LOW
	0002	HIGH
	<Note>
	If the fan motor has shut down, the alarm tone is sounded
	at the HIGH volume level regardless of this setting.

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

The underlining (__) denotes the factory setting mode.

86

No./Item		Description of setting
140*1	For selecting the output signals.
	0000	EE:
OUTPUT	<In the STOP mode>:
	The input signals selected by setup menu items
	No.600 (VIDEO IN SEL) and No.713 (CH1 IN SEL)
	to No.724 (D IN SEL 78) are output.
	<During recording or editing>:
	The input signals selected by setup menu items
	No.600 (VIDEO IN SEL) and No.713 (CH1 IN SEL)
	to No.724 (D IN SEL 78) are output:
	0001	TAPE:
	<In the STOP mode>
	The signals played back from the tape are output.
	<During recording or editing>:
	The simultaneous playback signals are output.
	<Note>
	In order to select the output signals during recording or
	editing, set setup menu item No.302 (CONFI EDIT).
141*1	For setting what is to be controlled by the
	audio volume controls on the front panel.
VOLUME	0000	REC:
	The controls function as REC volume controls.
	0001	PB:
	The controls function as PB volume controls.
	0002	AUTO:
	Normally, the controls function as PB volume
	controls. However, during recording or in the
	EE/INPUT CHECK status, they automatically
	function as REC volume controls.
142*1	For selecting the conditions under which the
	AUDIO UNITY lamp on the front panel is to light.
AUDIO UNITY	0000	IN:
	The lamp lights when all the audio input levels
	are set to the UNITY level.
	0001	OUT:
	The lamp lights when all the audio output
	levels are set to the UNITY level.
	0002	IN/OUT:
	The lamp lights when all the audio input and
	output levels are set to the UNITY level.
143	For setting whether the lighting of the tape
	mechanism is to be set to ON or remain OFF.
CASSTT	0000	OFF:
LIGHT	The mechanism does not light even when a
	cassette is inserted.
	0001	ON:
	The mechanism lights when a cassette is inserted.
144	For switching the preset registration method
	for the time code.
TC INPUT	0000 NORMAL:
	The time code is input starting with the left-
	most digit.
	0001	REV:
	The time code is input from the high-order digit
	but is displayed from the right-most digit.
145	For selecting whether the LCD monitor display on
	the front panel is to be turned on or off.
FRONT LCD	0000	OFF:
	The display is turned off.
	0001	ON:
	The display is turned on or off in synchronization
	with the screen saver operation for the time code
	display area.