Panasonic HD1700pe manual Error messages

Error messages

Warning messages

•Display

Priority • Description

•VTR operation and remedial action

Higher	FAN STOP
	This is displayed when the fan motor has stopped.
	VTR: Operation continues (and a warning beep is sounded
	regardless of the menu setting.)
	• Check that no foreign matter has accumulated on the fan.
	NO RF
	This is displayed when a blank part of the tape lasting for 1
	or more seconds has been detected during playback.
	When all of the following conditions have been met, it will be
	recognized as a blank part.
	• When no signals are output from any of the heads
	• When the playback data cannot be read
	• When the CTL signal is not present
	VTR: Operation continues.
	• Check the tape. An unrecorded tape may have been
	inserted.
	SERVO NOT LOCKED
	This is displayed when the servo is not locked for 3 or more
	seconds during playback, recording or editing.
	VTR: Operation continues.
	• Check the tape. A tape recorded using a system which
	does not allow playback may have been inserted.
	INVALID TC MODE (in 23/24 Hz or 25 Hz (HD or SD)
	mode)
	This is displayed during playback if the time code has been
	recorded in the drop frame mode. The video output is
	disturbed and the audio output is muted at the time code
	drop point.
	VTR: Operation continues.
	• Check the tape. If a tape recorded using a variable frame
	rate camera is to be played back in this VTR, the time
	code must be recorded in the non-drop frame mode.
	TC SEQUENCE UNMATCH (in 23/24 Hz or 25 Hz (HD or
	SD) mode)
	This is displayed during playback if the correlation between
	the active frame information and time code is irregular. The
	video output may not be uniform (the movements may not
	be smooth).
	VTR: Operation continues.
	• Check the tape. The active frame (first frame where the
	frame video is switched) information is recorded on a
	tape recorded using a variable frame rate camera. When
	such a tape is played back on this VTR, the 0 frame of
	the time code must be detected at the active frame
	position.
	LOW RF
	This is displayed when a state in which the envelope level
	has dropped to less than one-third of its normal level has
	been detected for 1 or more seconds or when a state in
	which the CTL signal level has dropped to less than one-
	sixth of its normal level has been detected for 1 or more
	seconds during playback, recording or editing.
	• The CTL signal level is not detected during DV or
	DVCAM playback.
	• During recording or editing, the envelope level of only the
	video simultaneous play heads is detected.
	VTR: Operation continues.
	• Clean the video heads and A/C head.
	HIGH ERROR RATE
	This is displayed when the error rate increases and
	correction or interpolation is performed for either the video
	or audio signals.
Lower	VTR: Operation continues.
	• Clean the video heads.

Error messages

Display	• Description
	• VTR operation and remedial action
CAP ROTA	If the rotational speed of the capstan motor is
TOO SLOW	abnormally slow, the AUTO OFF lamp lights, and the
	message display blinks.
	VTR: Stops.
	• Set the POWER switch to OFF and then back to ON
	again.
CAP TENSION	If an abnormal tension is detected at the supply side in
ERROR	the capstan mode, the AUTO OFF lamp lights, and the
	message display blinks.
	VTR: Stops.
	• Set the POWER switch to OFF and then back to ON
	again.
DEW	When condensation has been detected, the AUTO OFF
	lamp lights, the message display blinks, and the VTR
	transfers to the EJECT mode. After the tape has been
	ejected, the drum continues to rotate in order to dry out
	the condensation.
	When the condensation has cleared, the AUTO OFF
	lamp goes off, the message display is cleared, and the
	VTR is ready for operation again.
	• When condensation is detected in the EJECT mode,
	the drum starts rotating as soon as it is detected.
	• When condensation is detected while a cassette is
	inserted, the drum stops rotating and starts rotating
	again after the tape has been ejected.
	VTR: EJECT
	• Wait with the power on.
DRUM ROTA	If the rotational speed of the cylinder motor is
TOO FAST	abnormally high, the AUTO OFF lamp lights, and the
	message display blinks.
	VTR: Stops.
	• Set the POWER switch to OFF and then back to ON
	again.
DRUM ROTA	If the rotational speed of the cylinder motor is
TOO SLOW	abnormally slow, the AUTO OFF lamp lights, and the
	message display blinks.
	VTR: Stops.
	• Set the POWER switch to OFF and then back to ON
	again.
E-FF	If the tape start and tape end are detected at the same
	time either during or after loading, the AUTO OFF lamp
	lights, and the message display blinks.
	VTR: Stops.
	• Set the POWER switch to OFF and then back to ON
	again.
FRONT LOAD	If the take-up reel has turned without engaging the tape
ERROR	for a specific period of time during the tape start or end
	processing operation while loading is being performed
	(at the half position), the AUTO OFF lamp lights, and
	the message display blinks.
	VTR: Stops.
	• Set the POWER switch to OFF and then back to ON
	again.

120