Panasonic HD1700pe manual Time Code

Setup menus

<TIME CODE>

No./Item		Description of setting
500*4	For selecting whether or not to output the
	VITC signal at the positions selected by setup
VITC BLANK	menu items No.501 (VITC POS-1) and No.502
	(VITC POS-2).
	0000	BLANK:	The VITC signal is not output.
	0001	THRU:	The VITC signal is output.
	<Note>
	Only the SD output takes effect at this setting.
501*4	For setting the position where the VITC signal
	is to be inserted.
VITC POS-1	<59/60Hz>		<50Hz, 25Hz (SD)>
	0000	10L	0000	7L
	:	:	:	:
	0006	16L	0004	11L
	:	:	:	:
	0010	20L	0015	22L
	<Notes>

•The same line as the one selected by the setup menu item No.502 (VITC POS-2) cannot be selected.

•Only the SD output takes effect at this setting.

502*4	For setting the position where the VITC signal
	is to be inserted.
VITC POS-2	<59/60Hz>			<50Hz, 25Hz (SD)>
	0000		10L	0000	7L
	:		:	:	:
	0008		18L	0006	13L
	:		:	:	:
	0010		20L	0015	22L
	<Notes>
	• The same line as the one selected by the setup menu
	item No.501 (VITC POS-1) cannot be selected.
	• Only the SD output takes effect at this setting.
503*1	For setting the synchronization of the internal
	time code generator.
TCG MODE	0000	REGEN:
	The time code reader is synchronized with the
	time code which is read from the tape.
	0001		PRE:
	Presetting is enabled at the operation panel or
	by the remote controller.
	0002		AUTO:
	The REGEN and PRE settings are
	automatically switched in accordance with the
	operation mode.
	In the editing mode: REGEN is selected.
	In all other modes: PRE is selected.
504*1	For setting when			the	internal time code
	generator is to advance depending on the
RUN MODE	operation mode.
	0000		REC:
	The time code generator is advanced during
	recording.
	0001		FREE:
	The time code generator is advanced while the
	power is on regardless of which operation
	mode is established.

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

*2: This item is not displayed when the 23/24 Hz or 25 Hz (HD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

The underlining (__) denotes the factory setting mode.

No./Item		Description of setting
505*1	For selecting the regeneration signal when
	REGEN has been selected as the TCG (time
TCG REGEN	code generator) mode.
	0000	TC&UB:
	Regeneration applies to both the time code
	and user’s bit.
	0001	TC:
	Regeneration applies only to the time code only.
	0002	UB:
	Regeneration applies only to the user’s bit only.
506*1	For selecting the editing mode range when
	the VTR is operating in the REGEN mode
REGEN MODE	while	performing editing operations with
	“AUTO” selected as the setup menu item
	No.503 (TCG MODE) setting.
	0000	AS&IN:
	Regeneration applies during assemble or
	insert editing.
	0001	ASSEM:
	Regeneration applies during assemble editing.
	0002	INSRT:
	Regeneration applies during insert editing.
507*1	For selecting the time code to be used when
	HD SDI or SD SDI has been selected as the
TC SOURCE	setup menu item No.600 (VIDEO IN SEL)
	setting when an external time code is to be
	used.
	[When HD SDI has been selected]
	0000	INT:
	The time code of the internal time code
	generator is used.
	0001	EXT_L:
	LTC of the TIME CODE IN connector is used.
	0002	SLTC:
	The LTC information added to the serial
	signals which are input to HD SDI IN is used.
	0003	SVITC:
	The VITC information added to the serial
	signals which are input to HD SDI IN is used.
	[When SD SDI has been selected]
	0000	INT:
	The time code of the internal time code
	generator is used.
	0001	EXT_L:
	LTC of the TIME CODE IN connector is used.
	0002	VITC:
	The VITC information added to the serial
	signals which are input to SD SDI IN is used.
	<Note>
	If the VIDEO IN SEL input selection is changed, the time
	code is converted as shown below.
	[HD_SDI]		[SD_SDI]
	INT	↔	INT
	EXT_L	↔	EXT_L
	SLTC	↔	EXT_L
	SVITC	↔	VITC

91