Panasonic WJ-HD220 manual Post-alarm Recording Post ALM REC, Dynamic Recording Dynamic REC

●Post-alarm Recording (POST ALM REC)

This setting specifies the duration of alarm recording after an alarm input. Functions active during alarm recording are buzzer beeping, ALARM LED indication, "ALARM" status display, and the ALARM OUT signal.

1.Move the cursor to POST ALARM REC with the [D] or [C] button.

2.Select the desired duration with the JogDial. The default value is 10 seconds.

The unit will revert to the previous status when the time has elapsed.

Available times (seconds): 5, 10, 20, 30

Available times (minutes): 1, 1.5, 2, 3, 6

Continue: Recording continues until the [RESET] but- ton is pressed, or the RESET IN signal is supplied to the rear panel.

Manual: Recording continues for as long as the alarm input is active, or at least for 10 seconds if the input turns inactive earlier.

●Dynamic Recording (DYNAMIC REC)

This setting specifies the recording pattern on the disk when one or more alarms operate.

1.Move the cursor to DYNAMIC REC with the [D] or [C] button.

2.Select the parameter with the JogDial, and press the JogDial.

The default is OFF.

ALM-MULTI:Alarmed channels are recorded with pri- ority over others.

OFF: All channels are recorded with the same priority.

●Trigger Action Setup (TRIGGER ACTION SETUP)

This setting specifies the two roles of alarm recording and alarm control functions (Refer to page 47) in the post-alarm sequence.

TRIGGER ACTION SETUP

CAM	MODE	PRESET
1→	REC&ALM	––
2→	REC&ALM	––
3→	REC&ALM	––
4→	REC&ALM	––
5→	REC&ALM
6→	REC&ALM
7→	REC&ALM
8→	REC&ALM

When combination cameras are connected to VIDEO IN 1-4 on the rear panel, you can select a preset position for cam- eras 1-4. The camera will move to the preset position when an alarm other than VMD arises for the camera.

Notes:

•The preset position assignment on the TRIGGER ACTION SETUP menu is not available for each PROG n (1 - 4) SETUP menu, but available only for the REC SETUP menu.

•You need to preset desired positions for the camera prior to operation.

•VMD will not move the camera to the preset position.

1.Move the cursor to TRIGGER ACTION SETUPO, and press the JogDial.

The TRIGGER ACTION SETUP menu opens.

2.Move the cursor to the channel.

3.Select a mode with the JogDial, and press the JogDial. The default is REC&ALM.

OFF: Disables alarm recording or warning.

REC&ALM: Enables both alarm recording and warning.

REC: Enables alarm recording, but disables warning.

4.The cursor is at the PRESET column. Select a preset parameter with the JogDial, and press the JogDial.

1-64:Moves the camera to the specified preset posi- tion.

HOME: Moves the camera to the home position.

– –:Does not move the camera.

5.Repeat steps 2, 3 and 4 until all channels are set.

6.Press the [SETUP/ESC] button to return to the PROG1 SETUP, NO. 1 menu.

●Camera Recording Setup (CAM REC SETUP)

This setting is provided for the purpose of saving disk space. Setting allows each camera channel to be enrolled in all recording modes or exclusively in alarm recording.

CAM REC SETUP

CAMMODE

1REC

2REC

3REC

4ALM-ONLY

5REC

6ALM-ONLY

7REC

8REC

1.Move the cursor to CAM REC SETUP, and press the [SET] button. The CAM REC SETUP menu opens.

2.Move the cursor to the camera channel with the [D] or [C] button.

27