DSX-1 Interface Options, Esf, B8ZS

A. Configuration Options

DSX-1 Interface Options

For DSX-1 Interface Options, refer to Table A-2,DSX-1 Interface Options. To access the DSX-1 Interface Options screen, follow this menu selection sequence:

Main Menu→ Configuration→ Current Configuration → DSX-1

main/config/DSX-1	Hotwire
Slot 4	Model: 8784
Port 2
DSX-1 INTERFACE OPTIONS
Port Status:	Enable
Line Framing:	ESF
Line Coding:	B8ZS
Line Equalization:	0-133
Excessive Error Rate Threshold:	1E-4
Send (AIS) on Network Failure:	Enable
Send All Ones on DSX-1 Failure:	Enable
Primary Clock Source:	DSX-1

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu	MainMenu Exit
Save

A-4

February 2001

8784-A2-GB20-30

Page 78

Image 78

Paradyne 8784 manual DSX-1 Interface Options, Main Menu→ Configuration→ Current Configuration → DSX-1, Esf, B8ZS

Contents

Hotwire 8784 TDM Sdsl Termination Unit Copyright 2001 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Contents Initial Startup and Configuration Monitoring the UnitFebruary Security TestingMessages and Troubleshooting IP Addressing T Technical Specifications Glossary Index Configuration OptionsConnector Pin Assignments Standards ComplianceT for Snmp Traps About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents Document Number Document Title About the Hotwire Termination Unit TDM Sdsl Overview Hotwire 8784 Termination Unit Features Network Configuration Customer Premises CPCO Site Snmp Trap Support Snmp Management CapabilitiesManagement Information Base MIB Support Network Using the Asynchronous Terminal Interface User Interface AccessManagement Serial Port Settings Logging In to the Hotwire Dslam LoginInitiating an ATI Session Select Main Menu Menu Hierarchy Snmp Function Main Menu→ Configuration → Current Configuration → NetworkScreen Work Areas Keys Navigating the Screens Keyboard KeysPress Function Keys For the screen Function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Exiting From the Dslam Session Using the Asynchronous Terminal Interface February Initial Startup and Configuration Overview Entering Identity Information Main Menu→ Control→ Change IdentityIdentity Configuring the Unit Main Menu→ Configuration Load Configuration FromLoad Configuration from Current and Default Factory Configurations Configuration EDIT/DISPLAYIf you select Then Main Menu→ Configuration → Configuration Loader Configuration LoaderSelect To Access To Configure Configuration Loader Completed successfully Saving Configuration Changes Save Configuration Download Code Downloading FirmwareMain Menu→ Control → Download Code DSL1 Apply Download AutoRate Feature Main Menu→ Configuration→ Current Configuration → NetworkDisabling AutoRate Main Menu→ Control→ Reset AutoRate Restoring Access to the User InterfaceResetting AutoRate Select Configuration→ DSL Cards → Reset Slot Resetting the Unit Main Menu→ Control→ Reset Device Monitoring the Unit What to Monitor Viewing System and Test Status Main Menu→ Status→ System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Messages Yyyyyyyy Monitoring the Unit Self-Test Results Messages Test Status MessagesTest Status Messages Meaning Viewing Network Error Statistics Network Error StatisticsPerformance Statistics SES Severely Errored Seconds Seconds during which more than Field Contains Viewing Network Performance Statistics This Field Contains SES Viewing Current Network PerformanceCurrent Network Performance Statistics Febe Viewing DSX-1 Performance Statistics Main Menu→ Status→ Performance Statistics→ DSX-1 StatisticsDSX-1 Performance Statistics This Field Contains General Viewing LED StatusDisplay DSL Loop Front Panel LEDs TypeLED is Indicating Main Menu→ Test TestingAccessing the Test Menu Test Running Network Tests Main Menu→ Test→ Network & DSX-1 TestsNetwork & DSX-1 Tests Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Main Menu→ Test→ Device Tests Device TestsLamp Test Device Tests Configuration Options Ending an Active Test Telco-Initiated Payload Loopback Telco-Initiated TestsTelco-Initiated Line Loopback Activation Line Payload Remote Line Deactivation Loopback Telco-Initiated Remote Line Loopback CAP LIU DSL DSX-1 Testing February Messages and Troubleshooting Configuring Snmp Traps Snmp Traps OptionsNMS Device Messages Device Messages 1 What Message Indicates What To Do Device Messages 2 What Message Indicates What To Do Troubleshooting Troubleshooting Symptom Possible Cause Solutions Messages and Troubleshooting February ATI Access Levels Security Creating a Login Administer Logins Deleting a Login On the Login Entry Screen, for Enter Management Options, in Appendix A, Configuration Options Controlling Snmp AccessAssigning Snmp Community Names and Access Types Configuration Options, to IP Addressing Configurations Not Running IP Conservative SoftwareAll Configurations Selecting an IP Addressing Scheme IP Addressing Example Peer IP Address Assignments Configuration Options Configuration Changes in , Initial Startup and Configuration Network Interface Options Main Menu→ Configuration→ Current Configuration→ NetworkExcessive Error Rate Threshold Table A-1. Network Interface Options 1 AutoRate DSL Line Rate Possible Settings 400, 528, 784, 1040Table A-1. Network Interface Options 2 Circuit Identifier DSX-1 Interface Options Main Menu→ Configuration→ Current Configuration → DSX-1DSX-1 Interface Options ESF Line Framing Table A-2. DSX-1 Interface Options 1Port Status Line Coding Send All Ones on DSX-1 Failure Table A-2. DSX-1 Interface Options 2Send AIS on Network Failure Primary Clock Source Table A-3. Copy Ports Options Main Menu→ Configuration→ Current Configuration→ Copy PortsCopy Ports Options From Port n System Options Main Menu→ Configuration→ Current Configuration→ SystemSystem Options LTU Table A-4. System Options Management and Communication Menu Telnet Session Options Inactivity Timeout Telnet Login RequiredSession Access Level Table A-5. Telnet Session Options 1 Table A-5. Telnet Session Options 2 Main Menu→ Configuration→ Current Configuration→General Snmp Management Options Disconnect Time Minutes Table A-6. General Snmp Management Options Name 1 AccessName 2 Access Snmp Management Snmp NMS Security Options Snmp NMS Security Options Access Level Table A-7. Snmp NMS Security OptionsNMS IP Validation Snmp Trap Options Number of Trap Managers Table A-8. Snmp Trap Options 1Snmp Traps NMS n Destination Enterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, BothTable A-8. Snmp Trap Options 2 Link Traps Interfaces Snmp Traps AuthenticationFailureStandards Compliance for Snmp Traps WarmStart LinkUp and linkDown LinkUp/DownT Variable-Bindings Enterprise-Specific Traps DSL Network IfIndex RFC Connector Pin Assignments Front Panel 50-pin DTE Connector Pinouts50-Pin Connector DSX-1 Port Pinout Function Connector Pin Assignments February Technical Specifications Specifications Criteria Technical Specifications February Bridged tap Glossary511 COM port Ethernet Factory defaultsEIA-530-A Frame 704 Reset703 IP address RS-449 Yellow AlarmRouter Telnet Index IN-1 IN-2 IN-3 IN-4 IN-5 IN-6

Paradyne 8784 DSX-1 Interface Options, Main Menu→ Configuration→ Current Configuration → DSX-1

Models: 8784

DSX-1 Interface Options

Main Menu→ Configuration→ Current Configuration → DSX-1

DSX-1 INTERFACE OPTIONS

ESF

B8ZS