Table A-4. System Options | Paradyne 8784 specs

A. Configuration Options

Table A-4. System Options

DSL Mode

Possible Settings: LTU, NTU

Default Setting: LTU

Controls whether the unit is configured as a control unit or tributary unit.

LTU – The unit is configured as a control unit (Line Termination Unit).

NTU – The unit is configured as a tributary unit (Network Termination Unit). This unit will request its IP address from the LTU during establishment of the PPP link.

NOTE: Changing this option will reset the card.

Test Timeout

Possible Settings: Enable, Disable

Default Setting: Enable

Allows tests to end automatically. The feature should be enabled when the unit is remotely managed, so that control can be regained after a test is accidentally executed.

Enable – Loopback and pattern tests end when test duration is reached.

Disable – Tests run until manually terminated from the Network Tests screen or remotely (network initiated tests). Refer to Running Network Tests in Chapter 5, Testing.

Test Duration (min)

Possible Settings: 1 – 120

Default Setting: 10

NumberTof minutes for a test to be active before automatically ending.

Test Duration (min) option appears when Test Timeout is enabled.

1 – 120 – Amount of time in minutes for a test to run before terminating.

Telco Initiated Loopback

Possible Settings: Enable, Disable

Default Setting: Enable

Determines if the unit will respond to Telco loopback commands on the DSX-1 interface. See Telco-Initiated Tests in Chapter 5, Testing.

Enable – The unit will respond to Telco loopback commands.

Disable – The unit will not respond to Telco loopback commands.

Remote Telco Line Loopback

Possible Settings: Enable, Disable

Default Setting: Disable

Determines if the unit will perform a Telco initiated loopback on just the local unit or if the loopback will be performed on the remote DSL unit. See Telco-Initiated Tests in Chapter 5, Testing.

Enable – The loopback will be in the remote unit.

Disable – The loopback will be local.

8784-A2-GB20-30

February 2001

A-9

Image 83

Paradyne 8784 manual Table A-4. System Options

Contents

Hotwire 8784 TDM Sdsl Termination Unit Copyright 2001 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Contents February Initial Startup and ConfigurationMonitoring the Unit IP Addressing T TestingMessages and Troubleshooting Security Standards ComplianceT for Snmp Traps Configuration OptionsConnector Pin Assignments Technical Specifications Glossary Index Document Summary About This GuideDocument Purpose and Intended Audience Document Number Document Title Product-Related Documents TDM Sdsl Overview About the Hotwire Termination Unit Hotwire 8784 Termination Unit Features CO Site Network ConfigurationCustomer Premises CP Network Snmp Management CapabilitiesManagement Information Base MIB Support Snmp Trap Support Management Serial Port Settings Using the Asynchronous Terminal InterfaceUser Interface Access Initiating an ATI Session Logging In to the Hotwire DslamLogin Main Menu Select Snmp Menu Hierarchy Keys Main Menu→ Configuration → Current Configuration → NetworkScreen Work Areas Function Press Navigating the ScreensKeyboard Keys For the screen Function Select Press Enter to Function Keys Example Switching Between Screen Work Areas Exiting From the Dslam Session Ending an ATI Session Using the Asynchronous Terminal Interface February Overview Initial Startup and Configuration Identity Entering Identity InformationMain Menu→ Control→ Change Identity Load Configuration from Configuring the UnitMain Menu→ Configuration Load Configuration From If you select Then Current and Default Factory ConfigurationsConfiguration EDIT/DISPLAY Configuration Loader Configuration LoaderSelect To Access To Configure Main Menu→ Configuration → Configuration Loader Completed successfully Save Configuration Saving Configuration Changes DSL1 Downloading FirmwareMain Menu→ Control → Download Code Download Code Apply Download Disabling AutoRate AutoRate FeatureMain Menu→ Configuration→ Current Configuration → Network Select Configuration→ DSL Cards → Reset Slot Restoring Access to the User InterfaceResetting AutoRate Main Menu→ Control→ Reset AutoRate Main Menu→ Control→ Reset Device Resetting the Unit What to Monitor Monitoring the Unit System and Test Status Health and Status SELF-TEST Results Viewing System and Test StatusMain Menu→ Status→ System and Test Status Yyyyyyyy Health and Status Messages Monitoring the Unit Test Status Messages Meaning Self-Test Results MessagesTest Status Messages Performance Statistics Viewing Network Error StatisticsNetwork Error Statistics Field Contains SES Severely Errored Seconds Seconds during which more than Viewing Network Performance Statistics This Field Contains Febe Viewing Current Network PerformanceCurrent Network Performance Statistics SES DSX-1 Performance Statistics Viewing DSX-1 Performance StatisticsMain Menu→ Status→ Performance Statistics→ DSX-1 Statistics This Field Contains DSL Loop Viewing LED StatusDisplay General LED is Indicating Front Panel LEDsType Test TestingAccessing the Test Menu Main Menu→ Test Network & DSX-1 Tests Running Network TestsMain Menu→ Test→ Network & DSX-1 Tests Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Device Tests Device TestsLamp Test Main Menu→ Test→ Device Tests Ending an Active Test Configuration Options Activation Line Payload Remote Line Deactivation Loopback Telco-Initiated TestsTelco-Initiated Line Loopback Telco-Initiated Payload Loopback CAP LIU DSL DSX-1 Telco-Initiated Remote Line Loopback Testing February Messages and Troubleshooting NMS Configuring Snmp TrapsSnmp Traps Options Device Messages 1 What Message Indicates What To Do Device Messages Device Messages 2 What Message Indicates What To Do Troubleshooting Symptom Possible Cause Solutions Troubleshooting Messages and Troubleshooting February Security ATI Access Levels Administer Logins Creating a Login On the Login Entry Screen, for Enter Deleting a Login Configuration Options, to Controlling Snmp AccessAssigning Snmp Community Names and Access Types Management Options, in Appendix A, Configuration Options Selecting an IP Addressing Scheme Configurations Not Running IP Conservative SoftwareAll Configurations IP Addressing Peer IP Address Assignments IP Addressing Example Configuration Changes in , Initial Startup and Configuration Configuration Options Table A-1. Network Interface Options 1 Main Menu→ Configuration→ Current Configuration→ NetworkExcessive Error Rate Threshold Network Interface Options Circuit Identifier DSL Line Rate Possible Settings 400, 528, 784, 1040Table A-1. Network Interface Options 2 AutoRate ESF Main Menu→ Configuration→ Current Configuration → DSX-1DSX-1 Interface Options DSX-1 Interface Options Line Coding Table A-2. DSX-1 Interface Options 1Port Status Line Framing Primary Clock Source Table A-2. DSX-1 Interface Options 2Send AIS on Network Failure Send All Ones on DSX-1 Failure From Port n Main Menu→ Configuration→ Current Configuration→ Copy PortsCopy Ports Options Table A-3. Copy Ports Options LTU Main Menu→ Configuration→ Current Configuration→ SystemSystem Options System Options Table A-4. System Options Telnet Session Options Management and Communication Menu Table A-5. Telnet Session Options 1 Telnet Login RequiredSession Access Level Inactivity Timeout Disconnect Time Minutes Main Menu→ Configuration→ Current Configuration→General Snmp Management Options Table A-5. Telnet Session Options 2 Snmp Management Name 1 AccessName 2 Access Table A-6. General Snmp Management Options Snmp NMS Security Options Snmp NMS Security Options NMS IP Validation Access LevelTable A-7. Snmp NMS Security Options Snmp Trap Options NMS n Destination Table A-8. Snmp Trap Options 1Snmp Traps Number of Trap Managers Link Traps Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-8. Snmp Trap Options 2 Enterprise Specific Traps WarmStart AuthenticationFailureStandards Compliance for Snmp Traps Snmp Traps LinkUp/DownT Variable-Bindings LinkUp and linkDown Enterprise-Specific Traps DSL Network IfIndex RFC 50-Pin Connector DSX-1 Port Pinout Function Connector Pin AssignmentsFront Panel 50-pin DTE Connector Pinouts Connector Pin Assignments February Specifications Criteria Technical Specifications Technical Specifications February COM port Glossary511 Bridged tap Frame Factory defaultsEIA-530-A Ethernet IP address Reset703 704 Telnet Yellow AlarmRouter RS-449 IN-1 Index IN-2 IN-3 IN-4 IN-5 IN-6