Manuals / Paradyne / Computer Equipment / Network Card

Paradyne 8784 manual Resetting the Unit, 3-12, Main Menu→ Control→ Reset Device, Procedure

Models: 8784

1 110

Download 110 pages 56.67 Kb

Page 36

Image 36

3. Initial Startup and Configuration

Resetting the Unit

If the user interface is functional and you would like to reset the unit without removing it from the DSLAM, you can reset the unit from the Control menu.

Procedure

To reset the unit from the Control menu:

1. Follow this menu selection sequence:

Main Menu→ Control→ Reset Device

The message Are you sure? appears.

2. Enter Yes.

3-12

February 2001

8784-A2-GB20-30

Page 36

Image 36

Paradyne manual Resetting the Unit, 3-12, Main Menu→ Control→ Reset Device, Procedure, 8784-A2-GB20-30

Contents

Hotwire 8784 TDM SDSL Termination Unit with DSX-1 InterfaceUser’s Guide Document No. 8784-A2-GB20-30Warranty, Sales, Service, and Training Information Copyright 2001 Paradyne Corporation All rights reservedPrinted in U.S.A Document FeedbackImportant Safety Instructions EMI Notices UNITED STATES - EMI NOTICE CANADA - EMI NOTICEContents 1 About the Hotwire 8784 Termination Unit2 Using the Asynchronous Terminal Interface About This Guide3 Initial Startup and Configuration 4 Monitoring the UnitTesting Messages and TroubleshootingSecurity IP Addressing TA Configuration Options C Connector Pin AssignmentsD Technical Specifications Glossary Index B Standards ComplianceT for SNMP TrapsAbout This Guide Document Purpose and Intended AudienceDocument Summary Section8610-A2-GN10 Hotwire 8610 DSLAM Installation Instructions 8620-A2-GN20 Hotwire 8620 GranDSLAM Installation Guide8810-A2-GN11 Hotwire 8810 DSLAM Installation Instructions 8820-A2-GN20 Hotwire 8820 GranDSLAM Installation GuideAbout the Hotwire Termination UnitTDM SDSL Overview Hotwire 8784 Termination Unit Features Network Configuration Figure 1-1. Sample CO-to-CP ConfigurationFigure 1-2. Sample Campus Configuration SNMP Management Capabilities Management Information Base MIB SupportSNMP Trap Support Using the Asynchronous User Interface AccessManagement Serial Port Settings Terminal InterfaceLogging In to the Hotwire DSLAM Initiating an ATI SessionSelect Menu Hierarchy CopyT Main Menu→ Configuration → Current Configuration → Network Screen Work AreasProcedure Navigating the ScreensKeyboard Keys Function Keys Switching Between Screen Work Areas ExampleProcedure Ending an ATI Session Exiting From the DSLAM SessionProcedure Procedure2-10 2. Using the Asynchronous Terminal InterfaceFebruary 8784-A2-GB20-30Initial Startup and Configuration OverviewEntering Identity Information Main Menu→ Control→ Change IdentityConfiguring the Unit Main Menu→ Configuration Load Configuration FromProcedure Current and Default Factory Configurations Main Menu→ Configuration → Current ConfigurationMain Menu→ Configuration → Default Factory Configuration If you selectConfiguration Loader Main Menu→ Configuration → Configuration LoaderProcedure Completed successfullySaving Configuration Changes ProcedureDownloading Firmware Main Menu→ Control → Download CodeProcedure Procedure AutoRate Feature Main Menu→ Configuration→ Current Configuration → NetworkDisabling AutoRate 3-10Restoring Access to the User Interface Resetting AutoRateMain Menu→ Control→ Reset AutoRate 1. Select Configuration→ DSL Cards → Reset SlotResetting the Unit Main Menu→ Control→ Reset Device3-12 ProcedureMonitoring the Unit What to MonitorViewing System and Test Status Main Menu→ Status→ System and Test StatusHealth and Status Messages Table 4-1. Health and Status Messages 1 ofMessage What Message IndicatesTable 4-1. Health and Status Messages 2 of MessageWhat Message Indicates What To DoSelf-Test Results Messages Test Status MessagesViewing Network Error Statistics Network Error StatisticsPerformance Statistics Main Menu →SES Severely Errored Seconds Seconds during which more than FieldContains Viewing Network Performance Statistics Main Menu→ Status→ Performance Statistics→Network Performance Statistics Fields on this screen include This FieldContains Viewing Current Network Performance 4-10Current Network Performance Main Menu →Viewing DSX-1 Performance Statistics 4-11Main Menu→ Status→ Performance Statistics→ DSX-1 Statistics 4-12 This FieldContains Viewing LED Status 4-13Main Menu → Status → Display LEDsFront Panel LEDs 4-14Type LED isTesting Accessing the Test MenuMain Menu→ Test Running Network Tests Main Menu→ Test→ Network & DSX-1 TestsLine Loopback ProcedureRepeater Loopback ProcedureT1-to-T1 Repeater Loopback T1-to-V.35 Repeater LoopbackDTE Loopback ProcedureRemote Send Line Loopback ProcedureSend and Monitor ProcedureDevice Tests Lamp TestMain Menu→ Test→ Device Tests ProcedureT Configuration Options Ending an Active TestTelco-Initiated Tests Telco-Initiated Line LoopbackTelco-Initiated Payload Loopback 5-10Telco-Initiated Remote Line Loopback 5-115-12 5. TestingFebruary 8784-A2-GB20-30Messages and Troubleshooting Configuring SNMP Traps on pageT Device Messages on page 6-3 Troubleshooting on page OverviewConfiguring SNMP Traps Main Menu→ Configuration→ Current Configuration→Management and Communication→ SNMP Traps Device Messages nnn.nnn.nnn.nnnTable 6-1. Device Messages 2 of Device MessageWhat Message Indicates What To DoTroubleshooting Table 6-2. TroubleshootingSymptom Solutions6. Messages and Troubleshooting February8784-A2-GB20-30 ATI Access Levels SecurityTable 7-1. Access Levels ATI Access to Menu FunctionsCreating a Login ProcedureDeleting a Login ProcedureOn the Login Entry screen, for theControlling SNMP Access Assigning SNMP Community Names and Access TypesLimiting SNMP Access through the IP Addresses of the Managers Management Options, in Appendix A, Configuration OptionsConfigurations Not Running IP Conservative Software All ConfigurationsT Options, in Appendix A, Configuration Options T Appendix A, Configuration OptionsIP Addressing Example Figure 8-1. Peer IP Address AssignmentsConfiguration Options Configuration Changes in Chapter 3, Initial Startup and ConfigurationOverview Main Menu→ Configuration→ Current Configuration→ Network Network Interface OptionsExcessive Error Rate Threshold Margin ThresholdDSL Line Rate Possible Settings 400, 528, 784, 1040 Possible Settings 001.000.000.000 - 223.255.255.255, ClearAutoRate Peer IP AddressMain Menu→ Configuration→ Current Configuration → DSX-1 DSX-1 Interface Options8784-A2-GB20-30 Line Equalization Possible Settings 0-133, 133-266, 266-399, 399-533 Excessive Error Rate ThresholdPort Status Line FramingTable A-2. DSX-1 Interface Options 2 of Send AIS on Network FailureSend All Ones on DSX-1 Failure Primary Clock SourceMain Menu→ Configuration→ Current Configuration→ Copy Ports Copy Ports OptionsFrom Port n To Port yMain Menu→ Configuration→ Current Configuration→ System System Options8784-A2-GB20-30 DSL Mode Test TimeoutTest Duration min Telco Initiated LoopbackManagement and Communication Menu Telnet Session OptionsA-10 Management and Communication→ Telnet SessionA-11 Telnet Login RequiredSession Access Level Inactivity TimeoutGeneral SNMP Management Options A-12Management and Communication → General SNMP ManagementA-13 Name 1 AccessName 2 Access SNMP ManagementSNMP NMS Security Options A-14Management and Communication → SNMP NMS Security Main Menu→ Configuration→ Current Configuration→A-15 Number of Managers Possible Settings 1, 2, 3, 4, 5, 6, 7, 8, 9Possible Settings 001.000.000.000 - 223.255.255.255, Clear Access LevelSNMP Trap Options A-16Main Menu→ Configuration→ Current Configuration→ Management and Communication→ SNMP TrapsA-17 Possible Settings 001.000.000.000 - 223.255.255.255, ClearGeneral Traps Possible Settings Disable, Warm, AuthFail, Both SNMP TrapsA-18 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps SNMP TrapsauthenticationFailure Standards Compliance for SNMP TrapsSNMP Traps warmStartlinkUp and linkDown Enterprise-Specific Traps TifOperStatus RFC Connector Pin Assignments Front Panel 50-pin DTE Connector PinoutsOverview C. Connector Pin Assignments February8784-A2-GB20-30 Technical Specifications WeightPower SizeD. Technical Specifications February8784-A2-GB20-30 Glossary GL-1GL-2 GL-3 GL-4 Index IN-1IN-2 IN-3 IN-4 IN-5 IN-6 IndexFebruary 8784-A2-GB20-30