Philips intelligent remote control specification

Intelligent Remote Control User Guide

The information in this manual is copyright-protected. No part of this manual may be copied or reproduced in any form without prior written consent from Philips Electronics Corporation.

PHILIPS ELECTRONICS CORPORATION SHALL NOT BE LIABLE FOR OMISSIONS OR FOR TECHNICAL OR EDITORIAL ERRORS CONTAINED IN THIS MANUAL. PHILIPS ELECTRONICS CORPORATION SHALL NOT BE HELD LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE SUPPLYING OR USE OF THIS INFORMATION. PHILIPS ELECTRONICS CORPORATION SHALL NOT BE HELD LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE PERFORMANCE OR USE OF THE MATERIALS DESCRIBED IN THIS MANUAL.

The information in this manual may be subject to change without prior notice.

All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a different circuit from the receiver. Consult the dealer or an experienced radio/TV technician for help.

NOTE: If serial or parallel ports are configured, a filtered/shielded serial or parallel cable is recommended to minimize EMI and ensure FCC B compliance.

Image 2

Philips intelligent remote control manual Intelligent Remote Control User Guide

Contents

User guide Intelligent Remote Control User Guide User Guide Operate your components Insert batteriesTouch the screen to start Quickreference Modes Contents Settings Creating Macros Troubleshooting Specifications Command Reference Welcome Recharging dock FeaturesIntelligent remote control PC serial cable Installing AA batteries Batteries Battery Life Using the recharging dock Compartment Light is on while battery is charging Using the remote control Buttons and controls Touchscreen buttons Direct-access buttonsLeft and Right buttons This is called tapping the screen Getting startedTo turn the display on To adjust the display To turn on the backlight Home Tap one of the buttons to choose a device Device menu Opening the Device Menu Choosing a Device Control panels Scrolling to a Different Control Panel Use mode To switch devices without affecting the source Icon turns around to show a back view of the remote control Customizing the remote control To customize the remote control Optional Refine your configuration Refer to What are RC-5 and RC-6 CODES? Understanding modes For help, refer to Use mode on To switch modesTo show or hide the Mode menu Learning commands from other remote controls Learn mode Buttons that can learn commands To program a button on the display soft button Now you’re ready to use the new commands Repeat steps 4 and 5 to program other buttons Troubleshooting See the illustration on To program an item on the Device menuIf necessary, tap the Device tab once to extend it Remote control ﬂashes the word device To program a template button For instructions, see To relabel a button on Programming the direct-access and Left/Right buttons To program a button globally To program a direct-access button on a per-device basis To add a device Adding devices to your system Add modeRemote control displays a choice of buttons Choose how you want to add the new device Relabeling buttons and menu items Label mode To relabel a button Tap the button you want to relabel To relabel an item on a menu For details, refer to of To relabel a button on Rearranging items in menus Move modeTo rearrange the items in a menu After a few seconds, the remote control returns to Use mode Deleting buttons and menu items Delete mode To delete a button or button action To delete a device, Device menu action, or macro group Macro menu open in Delete Restoring Deleted BUTTONS, DEVICES, and Macro Groups Creating Macros Editing Macros Recording macros To record a macro Will belong to.Room for new macros on this panel Tap an empty button to start a new macro When you’re done, tap the Macro tab Troubleshooting Macros Contents of the macro appear on the display To view the commands in a macroTo view the commands in a macro while in Use mode Editing macros Edit the macro Display any macro panel or individual macro Organizing macros into groupsTo add a macro group Deleting Macros and Macro Groups To stop a macro Using macrosTo execute a macro Settings To adjust settings Adjust the settings as described in the following tables Duration Buttons TouchscreenBeep of the direct Need to use the Revert button To exit Setup Troubleshooting Problems using the remote control Buttons AREN’T Sending the Right Commands Remote Control WON’T LEARN/LABEL/DELETE Commands Problems using the recharging dock Remote Control Error Messages Common questions Additional procedures To reset the remote control Tap Cancel to exit without reverting To revert to the original configurationRemote control asks you to conﬁrm your choice To calibrate the touchscreen Seven programmable direct-access buttons Speciﬁcations for the intelligent remote controlHigh-resolution 320 ⋅ 240 liquid crystal display with Backlighting for LCD and direct-access buttons 110/220V-to-12V power adapter Automatic on/off no power switchNiMH 4.8V rechargeable battery pack 138 mm ⋅ 92 mm ⋅ 38 mm Command Reference Install Open / Close Cancel pictureSwitch screen a to B Video output Button Command Conﬁrm entry Serial Cable What is ProntoEditHow to receive ProntoEdit ProntoEdit System Requirements Service and support 8622 405