Contrast control, Memory | Philips intelligent remote control

7Speciﬁcations

Speciﬁcations for the intelligent remote control :

Hardware	High-resolution (320 ⋅ 240) liquid crystal display with
	contrast control
	Large touchscreen
	Seven programmable direct-access buttons
	Backlighting for LCD and direct-access buttons
	Light sensor with adjustable sensitivity
	Built-in RC-5 and RC-6 codes
	Infrared sending and learning eyes
	3-wire (RS232) serial port connector for future
	expandability
Software	Dynamic, animated interface
	Editable macros (up to 255 commands per macro)
	Total number of devices and macros limited only by
	memory
Infrared (IR)	Operating distance 10 meters (33 feet)
	Learning frequency up 56 KHz
	Learning distance 2.5cm (1 in) up to 30 cm (1 ft)
Memory	1 MB non-volatile ﬂash memory (retains commands when
	batteries aren’t present)
	512K SRAM
Batteries	4 AA 1.5V batteries, or one 4.8V rechargeable battery pack
Battery life	Approximately 6 months with typical use

Speciﬁcations 73

Image 75

Philips Speciﬁcations for the intelligent remote control, High-resolution 320 ⋅ 240 liquid crystal display with, Memory

Contents

User guide Intelligent Remote Control User Guide User Guide Insert batteries Touch the screen to startOperate your components Modes Quickreference Contents Creating Macros Settings Specifications Command Reference Troubleshooting Welcome PC serial cable FeaturesIntelligent remote control Recharging dock Batteries Installing AA batteries Battery Life Using the recharging dock Compartment Light is on while battery is charging Buttons and controls Using the remote control Direct-access buttons Left and Right buttonsTouchscreen buttons Getting started To turn the display onThis is called tapping the screen To turn on the backlight To adjust the display Tap one of the buttons to choose a device Home Opening the Device Menu Device menu Choosing a Device Scrolling to a Different Control Panel Control panels Use mode To switch devices without affecting the source Icon turns around to show a back view of the remote control To customize the remote control Customizing the remote control Optional Refine your configuration Refer to What are RC-5 and RC-6 CODES? Understanding modes To switch modes To show or hide the Mode menuFor help, refer to Use mode on Buttons that can learn commands Learning commands from other remote controls Learn mode To program a button on the display soft button Repeat steps 4 and 5 to program other buttons Now you’re ready to use the new commands Troubleshooting To program an item on the Device menu If necessary, tap the Device tab once to extend itSee the illustration on Remote control ﬂashes the word device For instructions, see To relabel a button on To program a template button To program a button globally Programming the direct-access and Left/Right buttons To program a direct-access button on a per-device basis Adding devices to your system Add mode Remote control displays a choice of buttonsTo add a device Choose how you want to add the new device To relabel a button Relabeling buttons and menu items Label mode Tap the button you want to relabel To relabel an item on a menu Rearranging items in menus Move mode To rearrange the items in a menuFor details, refer to of To relabel a button on After a few seconds, the remote control returns to Use mode To delete a button or button action Deleting buttons and menu items Delete mode To delete a device, Device menu action, or macro group Macro menu open in Delete Restoring Deleted BUTTONS, DEVICES, and Macro Groups Creating Macros Editing Macros To record a macro Recording macros Will belong to.Room for new macros on this panel Tap an empty button to start a new macro When you’re done, tap the Macro tab Troubleshooting Macros Editing macros To view the commands in a macroTo view the commands in a macro while in Use mode Contents of the macro appear on the display Edit the macro Organizing macros into groups To add a macro groupDisplay any macro panel or individual macro Deleting Macros and Macro Groups Using macros To execute a macroTo stop a macro To adjust settings Settings Duration Adjust the settings as described in the following tables Need to use the Revert button TouchscreenBeep of the direct Buttons To exit Setup Problems using the remote control Troubleshooting Buttons AREN’T Sending the Right Commands Remote Control WON’T LEARN/LABEL/DELETE Commands Remote Control Error Messages Problems using the recharging dock Common questions To reset the remote control Additional procedures To calibrate the touchscreen To revert to the original configurationRemote control asks you to conﬁrm your choice Tap Cancel to exit without reverting Backlighting for LCD and direct-access buttons Speciﬁcations for the intelligent remote controlHigh-resolution 320 ⋅ 240 liquid crystal display with Seven programmable direct-access buttons 138 mm ⋅ 92 mm ⋅ 38 mm Automatic on/off no power switchNiMH 4.8V rechargeable battery pack 110/220V-to-12V power adapter Command Reference Video output Cancel pictureSwitch screen a to B Install Open / Close Button Command Conﬁrm entry ProntoEdit System Requirements What is ProntoEditHow to receive ProntoEdit Serial Cable Service and support 8622 405