Promise Technology FAST TRAK100TM guide

FastTrak100 User Manual

NOTES

5

Image 9

Promise Technology FAST TRAK100TM user manual

Contents

Page Trademarks Table of Contents Troubleshooting & Tips Introduction What is the FastTrak100 RAID Card?Page Features Benefits Keys Features and Benefits Compatibility Page Unpacking Your FastTrak100 Getting Started Installing The Card Jumper Settings Installing The Hard DrivesPage Processor ID MHz Bios version Cache Server Tag Checking Cmos Settings Creating Your Disk Array Page Creating a Security Array With New Drives Creating an Array for Performance Creating a Security Array With An Existing Data Drive Page Page Viewing FastTrak100 Bios Screen Using FastBuild Configuration Utility Using the Main Menu Navigating the FastBuild Setup Menu Optimize Array For Auto Setup Options Menu Using a Hot Spare Drive Defining Typical Application UsageCreating Multiple Disk Arrays Mode Viewing Drive Assignments Manually Creating an Array Array No RAID Mode Total Drv CapacityMB Status Selecting Array Type Selecting Stripe BlockAssigning Drives to Array Adding Fault Tolerance to an Existing Drive Creating a Mirrored Array Using New Drives ChannelID Creating a Hot Spare Drive for Mirrored Arrays Making a FastTrak100 Disk Array Bootable How FastTrak100 Saves Array Information How FastTrak100 Orders Arrays Deleting An Array Press Ctrl-Y to Delete, others to Abort Total Drv CapacityMB Rebuilding a Mirrored Array Quantum CR8.4A Viewing Controller Settings Halting FastTrak Bios On Bootup ErrorsViewing FastTrak System Resources Page Installing Drivers Installing Driver During New Windows 2000 InstallationWindows Confirming Windows 2000 Installation Installing Driver in Existing Windows 2000 System Microsoft Millennium Installing Drivers During Millennium Installation Confirming Driver Installation in Millennium Installing Drivers with Existing Millennium System Windows 95/98 Installing Drivers During Windows 95/98 InstallationPage Installing Drivers with Existing Windows 95/98 DOS/Windows Confirming Driver Installation in Windows 98/95 Windows NT4.0 Installing Drivers During Windows NT 4.0 Installation Removing the Driver from Windows NT Installing Driver with Existing Windows NT Installing FastCheck Using The FastCheck Monitoring Utility Closing FastCheck Running FastCheck Viewing Array Information Using FastCheck Array Window Viewing Arrayed Drive Information Using Array Pull-down Menu Page Synchronizing An Array Page Rebuilding An Array Using Rebuild WizardPage Page Viewing Controller Card Information Using Controller Window Viewing IDE Channel Information Viewing Drive Information Using Options Window Selecting Notification Options Scheduling Array Synchronization User may then decide what to do about the errors detected Setting Rebuild Options Ignore FastTrak100 will log the event error and continue Setting Disk Parameters Option Setting PCI Bus Utilization Option Setting Screen Preferences Creating Password Changing PasswordDisabling Password FastBuild Auto Menu Setup About Adapter BiosUnderstanding Disk Array Concepts About FastTrak100 Disk Array Adapter Disk Array Terms Striping RAID About RAID Levels Mirroring RAID Using a Spare Drive About Dual Data Redundancy Striping/Mirror RAID 0+1 Spanning Jbod Motherboard Issues Troubleshooting & TipsConfiguring PCI IRQ resources System locks up during bootup or when Windows starts Drive-Related Errors System Cmos Issues Possible Master/Slave problems System Cmos displays C or D drive failure during StartupUnable to partition or format array ECC Error Reported on Rebuild ECC Error Reported on Synchronize Operating System-Related Errors Different drive lettering under Windows NTPromise Windows driver does not appear Device Manager Page Re-Configure PCI Latency Setting Performance TipsOptimize Array for Performance Change Setting of PCI Bus Utilization Page Pre-Installation Frequently Asked QuestionsWhat kind of hard drives can I use for a FastTrak100 array? Can I use Atapi devices on the FastTrak100 controller? RAID 0 stripe RAID 1 mirrorJbod spanning Do the HDDs on the FastTrak100 have to be the same size? Drive Issues How do I partition/format my FastTrak100 RAID array? Installation Issues Post-Installation Why does my system reboot after the Qemm driver loads fromWhy can’t I see the drives on the FastTrak100 under FDISK? Page Contacting Promise Support Appendix aUSA Tech Support Center Appendix a European Tech Support Pacific Rim Sales OfficeChina Office Appendix B Limited Warranty Appendix B Appendix C Returning Product For Repair Your Responsibilities Index Index C6101F100000000-1