Manuals / Q-Logic / Computer Equipment / Switch

Q-Logic 59021-05 B manual General Description, 1. SANbox2-16 Fibre Channel Switch, Section

Models: 59021-05 B

1 178

Download 178 pages 6.65 Kb

Page 19

Image 19

Section 2

General Description

This section describes the features and capabilities of the SANbox2-16 Fibre Channel switch. The following topics are described:

Chassis controls and LEDs

Fibre channel ports

Ethernet port

Serial port

Power supplies

Fans

Switch management

Fabrics are managed with the SANbox Manager switch management application (version 1.05) and the Command Line Interface (CLI). Refer to the SANbox2-8c/16 Switch Management User’s Guide for information about using the SANbox Manager application. Refer to Appendix B Command Line Interface for more information.

Figure 2-1. SANbox2-16 Fibre Channel Switch

59021-05 B

2-1

Page 19

Image 19

Q-Logic 59021-05 B manual General Description, 1. SANbox2-16 Fibre Channel Switch, Section

Contents

S i m p l i f y SANbox2-16 Fibre Channel Switch Installation GuideChange Document Revision HistoryAffected Section Table of Contents SectionIntroduction General DescriptionSection InstallationPlanning SectionSection Diagnostics/TroubleshootingPOST Diagnostics Chassis DiagnosticsSection Removal/ReplacementAppendix A Specifications Appendix B Command Line InterfaceFigures Glossary IndexPage Port-to-Port Transmission Combinations TablesCommands Listed by Authority Level Serial Port Pin IdentificationIntended Audience IntroductionSection Related Materials „ SANbox2-8c/16 Switch Management User’s Guide, Publication Number4-3, 4-5 Safety NoticesSicherheitshinweise Notes informatives relatives à la sécuritéFederal Communications Commission FCC Class A Statement Communications StatementsCanadian Department of Communications Class A Compliance Statement CE Statement BSMI Class A Statement VCCI Class A StatementElectrostatic Discharge Sensitivity ESDS Precautions Laser Safety InformationPièces Accessibles Accessible PartsZugängliche Teile Contact Information Technical SupportAvailability Training1-10 1 - Introduction Technical Support59021-05 B General Description Figure 2-1. SANbox2-16 Fibre Channel SwitchSection Figure 2-2. Chassis Controls and LEDS Power SwitchesMaintenance Button Chassis Controls and LEDsFigure 2-3. Chassis LEDs Over Temperature LED AmberChassis LEDs Fan Fail LED AmberFigure 2-4. Fibre Channel Ports Input Power LED GreenHeartbeat LED Amber Fibre Channel PortsFigure 2-6. Port LEDs Small Form-Factor Pluggable SFP TransceiversPort LEDs Figure 2-5. SFP TransceiverActivity LED Logged-In LEDPort Modes Translated Loop Port Fabric PortsExpansion Port Figure 2-8. Serial Port Ethernet PortSerial Port Figure 2-7. Ethernet PortFigure 2-9. Power Supply Components Power SuppliesTable 2-1. Serial Port Pin Identification Figure 2-10. Fans FansSwitch Management 2-12 2 - General Description Switch Management59021-05 B Devices PlanningSection Domain ID, Principal Priority, and Domain ID Lock Multiple Chassis FabricsCascade Topology Common TopologiesFigure 3-1. Cascade-with-a-Loop Topology Figure 3-2. Mesh Topology Mesh TopologyFigure 3-3. Multistage Topology Multistage TopologyDistance PerformanceTable 3-2. Port-to-Port Latency BandwidthLatency Table 3-1. Port-to-Port Transmission CombinationsDevice Access Soft Zones Access Control List Hard ZonesFabric Management Virtual Private Fabric Hard ZonesFabric Security 3-12 3 - Planning Fabric Security59021-05 B Fabric Management Workstation InstallationSwitch Power Requirements Site RequirementsFigure 4-1. SANbox2-16 Fibre Channel Switch Installing a SwitchEnvironmental Conditions Mount the Switch Figure 4-2. Installing Rack Mount Brackets Install SFP TransceiversAVERTISSEMENT Connect the Switch to AC PowerWARNUNG Appendix A Specificationsa. Check voltage at the AC power source b. Inspect the power cord Figure 4-3. Ethernet and Serial Cable Connections Connect the Management Workstation to the SwitchSerial Connection Ethernet Connection„ SANsurfer Management Suite Disk - Solaris Installation Install SANbox Manager„ SANsurfer Management Suite Disk - Windows Installation „ SANsurfer Management Suite Disk - Linux InstallationSANsurfer Management Suite Disk - Windows Installation mount /mnt/cdrom SANsurfer Management Suite Disk - Linux Installationchmod +x sansurferlinuxinstall.bin sansurferlinuxinstall.binchmod +x sansurfersolarisinstall.pkg SANsurfer Management Suite Disk - Solaris Installationsansurfersolarisinstall.pkg SANbox2 Installation Disk - Linux Installation SANbox2 Installation Disk - Windows InstallationSANbox2 Installation Disk - Solaris Installation Configure the Switch Cable Devices to the Switch Configure the PortsUsing SANbox Manager to Install Firmware Install FirmwareUsing the CLI to Install Firmware ftpbin ftpput filename Using FTP and the CLI to Install Firmwareuserimages password images cli $admin startcli admin $reset Powering Down a Switchcli admin $image list cli admin $image unpack filenameNormal all pass Diagnostics/TroubleshootingPOST Diagnostics Heartbeat LED Blink PatternsInternal Firmware Failure Blink Pattern Maintenance Mode PatternFatal Error Blink Pattern Configuration File System Error Blink Patternpasswordimages 0 Exit 1 Image Unpack 2 Reset Network Config 3 Reset Password File4 Copy Log Files 5 Remove Switch Config 6 Remake Filesystem 7 Reset Switch Optioni. Reset the switch and close the Telnet session. cli admin $reset ftpbin ftpput configdatatelnet xxx.xxx.xxx.xxx or telnet switchname cli admin $config restoreFigure 5-2. Logged-In LED Indications Logging In ErrorLogged-In LED Indications Figure 5-1. Port Logged-In LEDEPort Isolation Excessive Port Errors Page Figure 5-3. Chassis and Power Supply LEDs Chassis DiagnosticsFan Fail LED is Illuminated Chassis Over Temperature LED is IlluminatedInput Power LED Is Extinguished „ No - Refer to ”Output Power LED Is Extinguished” on pagePower Supply Over Temperature LED is Illuminated Output Power LED Is ExtinguishedRecovering a Switch Maintenance - Image Unpack Maintenance - ExitMaintenance - Remove Switch Config Maintenance - Reset Network ConfigMaintenance - Reset Password File Maintenance - Copy Log FilesAVERTISSEMENT Removal/ReplacementSection WARNUNGSFP Transceivers Figure 6-1. SFP Transceiver InstallationPower Supplies Figure 6-2. Power Supply RemovalFans Figure 6-3. Fan RemovalFigure 6-4. Fan Installation for Switch Model SB2A-16B 59021-05 B 6 - Removal/Replacement FansSwitch Specifications SpecificationsAppendix A Switch Maintainability Switch Electrical Switch DimensionsFabric Management Switch Regulatory Certifications Switch EnvironmentalTwo fans front-to-back or back-to-front Shortwave Laser SFP 1G/2G multi-mode Longwave Laser SFP 1G/2G single-mode Logging On to a Switch Command Line InterfaceAppendix B Command Syntax Table B-1. Commands Listed by Authority Level CommandsKeywords Admin CommandAuthority SyntaxAuthority Admin Syntax alias Alias Commandremove alias members members aliasrename aliasold aliasnew activate config backup cancel Config CommandSyntax config Keywords activate configrestore save configKeywords MMDDhhmmCCYY Date CommandSyntax date MMDDhhmmCCYYExamples Fallback CommandAuthority SyntaxAuthority User Help CommandKeywords command Syntax help command keywordAuthority User Syntax history History CommandAuthority Admin Syntax image cleanup Image CommandKeywords cleanup Authority Admin Lip CommandSyntax passwd accountname Keywords accountname Passwd CommandAuthority User Syntax ping Ping CommandExamples Ps CommandAuthority SyntaxAuthority User Quit CommandSyntax quit, exit, or logout Authority Reset Commandconfig configname config confignameDefault Table B-2. Switch Configuration DefaultsTable B-3. Port Configuration Defaults DefaultDefault Table B-3. Port Configuration Defaults ContinuedTable B-4. Alarm Threshold Configuration Defaults DefaultDefault Table B-4. Alarm Threshold Configuration Defaults ContinuedTable B-5. SNMP Configuration Defaults DefaultDefault Table B-6. System Configuration DefaultsParameter Syntax set Set Commandswitch state setup optionport option ports portnumber Set Config CommandTable B-7. Set Config Port Parameters port portnumberParameter Table B-7. Set Config Port Parameters ContinuedDescription Parameter Table B-8. Set Config Switch ParametersDescription threshold Table B-9. Set Config Threshold ParametersDescription Table B-10. Set Config Zoning ParametersExamples The following is an example of the Set Config Port command ParameterThe following is an example of the Set Config Threshold command The following is an example of the Set Config Switch commandB-32 B - Command Line Interface Set Config Command59021-05 B the ENTER The following is an example of the Set Config Zoning commandconfiguration must be saved see config save command andKeywords Set Log CommandAuthority SyntaxOther Monitors other miscellaneous events Port and the Level keyword to Info at the same time startstop Stops logging of eventsAuthority Admin Set Port CommandSyntax Set Setup CommandTable B-11. SNMP Configuration Settings AuthorityDescription Table B-12. System Configuration SettingsTable B-11. SNMP Configuration Settings EntryTable B-12. System Configuration Settings Continued 59021-05 B B - Command Line Interface Set Setup CommandB-41 The following is an example of the Set Setup System command port portnumber post log Show CommandKeywords about log option lsdbdonor log optionns option domainsport portnumber perf optionTable B-13. Show Port Parameters Displays performance information for all ports. Refer to the ”Show Perf Command” on page B-58Entry Table B-13. Show Port Parameters ContinuedDescription „ Date „ Alias List „ Config List „ Date „ History „ Ps steering domainidTable B-13. Show Port Parameters Continued Displays switch operational information The following is an example of the Show NS DomainID command The following is an example of the Show NS local domain commandThe following is an example of the Show Interface command Class2FramesOut The following is an example of the Show Port commandTotalLinkResets PL-XPL-00-S23-00The following is an example of the Show Topology command The following is an example of the Show Switch commandIPAddress The following is an example of the Show Topology command for portThe following is an example of the Show Version command 10.0.0.1 use set setup system to updateport portnumber Show Config CommandSyntax KeywordsThe following is an example of the Show Config Threshold command The following is an example of the Show Config Switch commandThe following is an example of the Show Config Zoning command Authority User Show Log CommandKeywords component settingsThe following is an example of the Show Log command The following is an example of the Show Log Options commandSyntax Show Perf Commanderrors AuthorityThe following is an example of the Show Perf Byte command Examples The following is an example of the Show Perf commandKeywords Show Setup CommandAuthority SyntaxThe following is an example of the Show Setup System command Authority Admin Shutdown CommandSyntax shutdown Syntax test Test CommandPage 3. A series of test parameters are displayed on the screen. Press the Enter key to accept each default parameter value, or type a new value for each parameter and press the Enter key. The TestLength parameter is the number of frames sent, the FrameSize 256 byte maximum in some cases parameter is the number of bytes in each frame, and the DataPattern parameter is the pattern in the payload. Before running the test, make sure that the device attached to the port can handle the test parameters Authority User Syntax uptime Uptime CommandKeywords accounts User Commandpassword 4-20 chars The following is an example of the User Add commandThe following is an example of the User Delete command The following is an example of the User List commandExamples Whoami CommandAuthority SyntaxSyntax zone Zone Commandrename zoneold zonenew listmembers zone remove zone membersThe following is an example of the Zone Members command Examples The following is an example of the Zone List commandzoneset1 The following is an example of the Zone Zonesets commandSANbox2 # zone zonesets zone1 Current List of ZoneSets for Zone wwnb0241fSyntax zoneset Zoneset CommandRemoves a list of zones given by zonelist from the zone set given by SANbox2 # zoneset zones ssss Current List of Zones for ZoneSet ssss The following is an example of the Zoneset Zones commandzone1 zone2 zone3 Keywords active Zoning CommandExamples The following is an example of the Zoning Edit command 59021-05 B B - Command Line Interface Zoning CommandB-79 B-80 B - Command Line Interface Zoning Command59021-05 B Glossary Frame Private Loop Glossary-4 SANbox2-16 Fibre Channel Switch Installation Guide59021-05 B Numerics IndexPage Page Page Page add member zone B-74 copy B-74