PQ Advanced Evaluation Setup | Schneider Electric PM870, PM820

PowerLogicTM Series 800 Power Meter	63230-500-225A2
Chapter 3—Operation	3/2011

PQ Advanced Evaluation Setup

1.Perform steps 1 through 5 of the SETUP MODE Access procedure on page 11.

2.Press ###: until ADVAN (advanced setup) is visible.

3.Press ADVAN.

4.Press ###: until PQADV is visible.

5.Press PQADV.

6.Select ON.

7.Press OK.

8.Change the nominal voltage (NOM V) value if desired (the default is 230).

9.Press OK to return to the SETUP MODE screen.

10.At the SETUP MODE screen, continue programming additional setup features or press1; until you are asked to save changes.

11.Press YES to save your changes and reset the power meter.

Power Demand Configuration Setup

1.Perform steps 1 through 5 of the SETUP MODE Access procedure on page 11.

2.Press ###: until ADVAN (advanced setup) is visible.

3.Press ADVAN.

4.Press ###: until DMD is visible.

5.Press DMD (P-DMD, I-DMD).

6.Select the demand configuration. Choices are

COMMS, RCOMM, CLOCK, RCLCK, IENGY, THERM, SLIDE, BLOCK, RBLCK, INPUT, and

RINPUT.

7.Press OK.

8.Enter the INTVL (interval) and press OK.

9.Enter the SUB-I (sub-interval) and press OK.

10.At the SETUP MODE screen, continue programming additional setup features or press1; until you are asked to save changes.

11.Press YES to save the changes.

PLSD110232

22	© 2011 Schneider Electric. All Rights Reserved.

Image 28

Schneider Electric PM870, PM820, PM810, PM850 manual PQ Advanced Evaluation Setup, Power Demand Configuration Setup

Contents

User Guide Page Hazard Categories and Special Symbols 63230-500-225A2 PowerLogicTM Series 800 Power Meter 2011 PowerLogicTM Series 800 Power Meter 63230-500-225A2 2011 Contents Maintenance and Troubleshooting Waveform CaptureDisturbance Monitoring PM870 Glossary What is a Power Meter? IntroductionTopics Not Covered In This Manual 2011 Introduction Power Meter Hardware Power Meter With Integrated DisplayPowerLogicTM Series 800 Power Meter Introduction 2011 Power Meter Without Display Parts of the Series 800 Power Meter without display Power Meter With Remote Display Parts of the remote display Description Power Meter Parts and Accessories Electric Box Contents Features Series 800 Power Meter FeaturesFirmware PM820 PM850 PM870 Introduction 2011 Schneider Electric. All Rights Reserved Safety Precautions 2011 Safety PrecautionsPage Power Meter Display OperationHow the Buttons Work Changing Values Level Setup Mode Access Power Meter SetupDate Setup Time Setup Lang Language Setup Comms Communications Setup Meter SetupCTs Setup Communications Default Settings Communications Setting HZ System Frequency Setup PTs SetupSYS System Type Setup Alarm Alarms Setup Input/Output Setup Passw Password Setup Advan Advanced Power Meter Setup Features Timer Operating Time Threshold SetupROT Phase Rotation Setup THD Calculation Setup INC Incremental Energy Interval SetupVAR/PF Convention Setup Alarm Backlight Setup Lock Resets SetupBar Graph Setup PQ Advanced Evaluation Setup Power Demand Configuration Setup Initialize the Power Meter Power Meter ResetsAccumulated Energy Readings Reset Minimum/Maximum Values Reset Accumulated Demand Readings ResetDisplay Mode Change Power Meter Diagnostics Accumulated Operating Time Reset Read and Write Registers View the Meter InformationView the Meter Date and TIme Metering Capabilities Real-Time Readings2011 Metering Capabilities One-second, Real-time Readings Reportable Range Power Factor Min/Max Conventions Min/Max Values for Real-time Readings Power Factor Sign Conventions Real Demand Readings Demand Power Calculation MethodsDemand Readings Reportable Range Sliding Block Fixed Block Demand Current Thermal Demand Example Predicted demand is updated every second Predicted DemandPeak Demand Generic Demand Input Metering Demand Pulse hour second Energy Readings Accumulated EnergyAccumulated Energy, Conditional Accumulated Energy, Incremental Energy-Per-Shift PM810 with PM810LOG ConfigurationEnergy-per-shift recorded values Category Recorded Values Power Analysis Values Values -3 to Default Fundamental Voltages per phase Fundamental Currents per phaseTHD-Voltage, Current Miscellaneous Input/Output Capabilities Digital Inputs Normal Demand Mode External Synch Pulse Demand Timing Demand Synch Pulse InputRelay Output Operating Modes Normal End Of Power Demand Interval LatchedTimed Absolute kWh Pulse Wire Pulse Initiator Solid-state KY Pulse OutputKWh Out Pulse KVARh Out Pulse Fixed Pulse Output Calculating the Kilowatthour-Per-Pulse Value Analog Outputs Analog Inputs= 0.1111 kWh/pulse Alarms Basic AlarmsBasic Alarm Groups 2011 Alarms Setpoint-driven Alarms EV2Max2EV1Max1 Max2 Priorities Viewing Alarm Activity and HistoryTypes of Setpoint-controlled Functions Schneider Electric. All Rights Reserved Scale Factors Scale Groups Measurement Range Scale Factor Scaling Alarm Setpoints Alarm Conditions and Alarm NumbersScale Group Register Numbers Limit Standard Speed Alarms 1 Second Digital Standard Speed Advanced Alarms Advanced Alarm GroupsAdvanced alarm features by model PM850 PM870 Alarm Levels Abbreviated Test Display Name Register Nand Introduction Logging2011 Logging Alarm Log Maintenance LogAlarm Log Storage Memory Allocation for Log Files Value Stored Number Data Logs Registers Alarm-driven Data Log Entries Billing LogOrganizing Data Log Files PM850, PM870 Data LogPage 2011 Logging Billing Log Register List Description Configure the Billing Log Logging IntervalData Type➀ Page Waveform Capture Waveform Capture2011 Waveform Capture Number Channels How the Power Meter Captures an Event Channel Selection in PowerLogic SoftwareWaveform Storage Initiating a Waveform Disturbance Monitoring PM870 63230-500-225A2 PowerLogicTM Series 800 Power Meter 2011About Disturbance Monitoring Plant a Transformer Plant C Plant D FaultPlant B 63230-500-225A2 PowerLogic TM Series 800 Power Meter 2011 Capabilities of the PM870 During an EventPage Power Meter Memory Maintenance and TroubleshootingDate and Time Settings Viewing the Display in Different Languages Identifying the Firmware Version, Model, and Serial NumberTechnical Support Troubleshooting Heartbeat LED CT and PT ratings, System Type, Nominal Using This Appendix What is Normal? Section I Common Problems for 3-Wire and 4-Wire Systems Section I-Case aSection I-Case B Section I-Case C Section II 3-Wire System Troubleshooting Section III 4-Wire System Troubleshooting Section III-Case aSection III-Case B Section III-Case C Section III-Case F Section III-Case ESection III-Case G Troubleshooting Diagnosis Readings from a 4-wire systemField Example Register List Access Appendix B-Register ListAbout Registers Floating-point Registers How Signed Power Factor is Stored in the Register How Date and Time are Stored in RegistersTable B-1 Date and Time Format Table B-2 Date and Time Byte Example Supported Modbus Commands Resetting RegistersTable B-3 Modbus Commands Table B-4 Register Listing-Reset Commands Schneider Electric All Rights Reserved Appendix C-Using the Command Interface Overview of the Command Interface Table C-2 Command Codes Issuing CommandsCommand Resets Files Operating Outputs from the Command Interface Setup9020 None Enter into setup mode 9021 8001 Exit setup mode and save all changes Conditional Energy To save the changes, write the value 1 to register Incremental Energy Command Interface ControlDigital Input Control Using Incremental Energy Figure C-2 Incremental energy example Setting Up Individual Harmonic Calculations Changing Scale Factors Enabling Floating-point RegistersPage Appendix D-Advanced Power Quality Evaluations Power Quality StandardsSEMI-F47/ITI Cbema Specification Table D-2 Duration categories Appendix D-Advanced Power Quality Evaluations PowerLogicTM Series 800 Power Meter 63230-500-225A2Table D-3 Categorized disturbance levels F-47 Sag levels Table D-4 Duration categories How Evaluation Results Are Reported EN501602000 SpecificationTable D-6 Register Entries Description Number Possible Configurations Through Register Writes Power FrequencyEvaluation During Normal Operation1 Supply Voltage Variations Evaluations During Abnormal Operation Supply Voltage UnbalanceHarmonic Voltage Count of Magnitude of Rapid Voltage Changes Detection of Interruptions of the Supply Voltage Table D-8 Voltage dip classificationsTable D-9 Voltage interruptions Duration t seconds Table D-10 Over-voltages Duration t seconds Operation with PQ Advanced Enabled Resetting StatisticsHarmonic Calculations Time Intervals 100 Schneider Electric. All Rights Reserved Portal Registers Table D-12 Portal Register Descriptions Size Data101 Detection and Classification of Supply Voltage Dips on Detecting and Classifying Temporary Power Frequency Over 102 Schneider Electric. All Rights Reserved 103 Setting Up PQ Advanced Evaluation from the Display Alarms Allocated for PQ Advanced Evaluations Glossary Terms63230-500-225A2 3/2011 105 106 Schneider Electric. All Rights Reserved 2011 Glossary Abbreviations and Symbols107 108 Schneider Electric. All Rights Reserved PowerLogicTM Series 800 Power Meter Index Index63230-500-225A2 3/2011 109 110 PLC 111 VAR 112Page PowerLogic Power Meter 800 User Guide