Using Incremental Energy | Schneider Electric PM820, PM870, PM810

63230-500-225A2	PowerLogicTM Series 800 Power Meter
3/2011	Appendix C—Using the Command Interface

Using Incremental Energy

Incremental energy accumulation begins at the specified start time and ends at the specified end time. When the start time arrives, a new incremental energy period begins. The start and end time are specified in minutes from midnight. For example:

Interval: 420 minutes (7 hours)

Start time: 480 minutes (8:00 a.m.) End time = 1440 minutes (12:00 p.m.)

The first incremental energy calculation will be from 8:00 a.m. to 3:00 p.m. (7 hours) as illustrated in Figure C–2. The next interval will be from 3:00 p.m. to 10:00 p.m., and the third interval will be from 10 p.m. to 12:00 p.m. because 12:00 p.m. is the specified end time. A new interval will begin on the next day at 8:00 a.m. Incremental energy accumulation will continue in this manner until the configuration is changed or a new interval is started by a remote master.

Figure C–2: Incremental energy example

PLSD110149

10

9

End Time

12

11			rva
		te				l
		In
	t
	s
1
						l
					a
				v
				r
			e
			t
		In
		d
	3	r
	3

1

2

3

Start Time 8

4

2
n
	d

7

In

terval

5

6

1st Interval (7 hours) = 8:00 a.m. to 3:00 p.m

2nd Interval (7 hours) = 3:00 p.m. to 10:00 p.m 3rd Interval (2 hours) = 10:00 p.m. to 12:00 p.m

•Set up—To set up incremental energy:

1.Write command code 9020 to register 8000.

2.In register 3230, write a start time (in minutes-from-midnight).

3.For example, 8:00 am is 480 minutes.

4.In register 3231, write an end time (in minutes-from-midnight).

5.Write the desired interval length, from 0–1440 minutes, to register 3229.

6.If incremental energy will be controlled from a remote master, such as a programmable controller, write 0 to the register.

7.Write 1 to register 8001.

8.Write command code 9021 to register 8000.

•Start—To start a new incremental energy interval from a remote master, write command code 6910 to register 8000.

© 2011 Schneider Electric. All Rights Reserved.

89

Image 97

Schneider Electric PM820, PM870, PM810, PM850 manual Using Incremental Energy, Figure C-2 Incremental energy example

Contents

User Guide Page 63230-500-225A2 PowerLogicTM Series 800 Power Meter 2011 Hazard Categories and Special Symbols PowerLogicTM Series 800 Power Meter 63230-500-225A2 2011 Contents Waveform Capture Maintenance and TroubleshootingDisturbance Monitoring PM870 Glossary Introduction What is a Power Meter?Topics Not Covered In This Manual 2011 Introduction Power Meter With Integrated Display Power Meter HardwarePowerLogicTM Series 800 Power Meter Introduction 2011 Parts of the Series 800 Power Meter without display Power Meter Without Display Parts of the remote display Description Power Meter With Remote Display Electric Power Meter Parts and Accessories Box Contents Series 800 Power Meter Features FeaturesFirmware PM820 PM850 PM870 Introduction 2011 Schneider Electric. All Rights Reserved 2011 Safety Precautions Safety PrecautionsPage Operation Power Meter DisplayHow the Buttons Work Changing Values Level Setup Mode Access Power Meter SetupDate Setup Lang Language Setup Time Setup Meter Setup Comms Communications SetupCTs Setup Communications Default Settings Communications Setting HZ System Frequency Setup PTs SetupSYS System Type Setup Alarm Alarms Setup Passw Password Setup Input/Output Setup Advan Advanced Power Meter Setup Features Timer Operating Time Threshold SetupROT Phase Rotation Setup THD Calculation Setup INC Incremental Energy Interval SetupVAR/PF Convention Setup Alarm Backlight Setup Lock Resets SetupBar Graph Setup Power Demand Configuration Setup PQ Advanced Evaluation Setup Initialize the Power Meter Power Meter ResetsAccumulated Energy Readings Reset Minimum/Maximum Values Reset Accumulated Demand Readings ResetDisplay Mode Change Accumulated Operating Time Reset Power Meter Diagnostics Read and Write Registers View the Meter InformationView the Meter Date and TIme Real-Time Readings Metering Capabilities2011 Metering Capabilities One-second, Real-time Readings Reportable Range Min/Max Values for Real-time Readings Power Factor Min/Max Conventions Real Power Factor Sign Conventions Demand Readings Demand Power Calculation MethodsDemand Readings Reportable Range Fixed Block Sliding Block Thermal Demand Example Demand Current Predicted Demand Predicted demand is updated every secondPeak Demand Generic Demand Pulse hour second Input Metering Demand Accumulated Energy Energy ReadingsAccumulated Energy, Conditional Accumulated Energy, Incremental Energy-Per-Shift PM810 with PM810LOG ConfigurationEnergy-per-shift recorded values Category Recorded Values Values -3 to Default Power Analysis Values Fundamental Currents per phase Fundamental Voltages per phaseTHD-Voltage, Current Miscellaneous Digital Inputs Input/Output Capabilities Demand Synch Pulse Input Normal Demand Mode External Synch Pulse Demand TimingRelay Output Operating Modes Normal Latched End Of Power Demand IntervalTimed Absolute kWh Pulse Solid-state KY Pulse Output Wire Pulse InitiatorKWh Out Pulse KVARh Out Pulse Calculating the Kilowatthour-Per-Pulse Value Fixed Pulse Output Analog Outputs Analog Inputs= 0.1111 kWh/pulse Basic Alarms AlarmsBasic Alarm Groups 2011 Alarms EV2Max2 Setpoint-driven AlarmsEV1Max1 Max2 Priorities Viewing Alarm Activity and HistoryTypes of Setpoint-controlled Functions Schneider Electric. All Rights Reserved Scale Groups Measurement Range Scale Factor Scale Factors Alarm Conditions and Alarm Numbers Scaling Alarm SetpointsScale Group Register Numbers Limit Digital Standard Speed Alarms 1 Second Standard Speed Advanced Alarm Groups Advanced AlarmsAdvanced alarm features by model PM850 PM870 Alarm Levels Abbreviated Test Display Name Register Nand Introduction Logging2011 Logging Maintenance Log Alarm LogAlarm Log Storage Memory Allocation for Log Files Number Value Stored Registers Data Logs Billing Log Alarm-driven Data Log EntriesOrganizing Data Log Files PM850, PM870 Data LogPage 2011 Logging Billing Log Register List Description Configure the Billing Log Logging IntervalData Type➀ Page Waveform Capture Waveform Capture2011 Waveform Capture Number Channels Channel Selection in PowerLogic Software How the Power Meter Captures an EventWaveform Storage Initiating a Waveform Disturbance Monitoring PM870 63230-500-225A2 PowerLogicTM Series 800 Power Meter 2011About Disturbance Monitoring Plant a Transformer Plant C Plant D FaultPlant B Capabilities of the PM870 During an Event 63230-500-225A2 PowerLogic TM Series 800 Power Meter 2011Page Power Meter Memory Maintenance and TroubleshootingDate and Time Settings Viewing the Display in Different Languages Identifying the Firmware Version, Model, and Serial NumberTechnical Support Heartbeat LED Troubleshooting CT and PT ratings, System Type, Nominal What is Normal? Using This Appendix Section I-Case a Section I Common Problems for 3-Wire and 4-Wire SystemsSection I-Case B Section I-Case C Section II 3-Wire System Troubleshooting Section III-Case a Section III 4-Wire System TroubleshootingSection III-Case B Section III-Case C Section III-Case F Section III-Case ESection III-Case G Troubleshooting Diagnosis Readings from a 4-wire systemField Example Appendix B-Register List Register List AccessAbout Registers Floating-point Registers How Date and Time are Stored in Registers How Signed Power Factor is Stored in the RegisterTable B-1 Date and Time Format Table B-2 Date and Time Byte Example Resetting Registers Supported Modbus CommandsTable B-3 Modbus Commands Table B-4 Register Listing-Reset Commands Schneider Electric All Rights Reserved Overview of the Command Interface Appendix C-Using the Command Interface Table C-2 Command Codes Issuing CommandsCommand Files Resets Setup Operating Outputs from the Command Interface9020 None Enter into setup mode 9021 8001 Exit setup mode and save all changes To save the changes, write the value 1 to register Conditional Energy Incremental Energy Command Interface ControlDigital Input Control Figure C-2 Incremental energy example Using Incremental Energy Setting Up Individual Harmonic Calculations Enabling Floating-point Registers Changing Scale FactorsPage Power Quality Standards Appendix D-Advanced Power Quality EvaluationsSEMI-F47/ITI Cbema Specification Table D-2 Duration categories PowerLogicTM Series 800 Power Meter 63230-500-225A2 Appendix D-Advanced Power Quality EvaluationsTable D-3 Categorized disturbance levels F-47 Sag levels Table D-4 Duration categories How Evaluation Results Are Reported EN501602000 SpecificationTable D-6 Register Entries Description Number Power Frequency Possible Configurations Through Register WritesEvaluation During Normal Operation1 Supply Voltage Variations Supply Voltage Unbalance Evaluations During Abnormal OperationHarmonic Voltage Count of Magnitude of Rapid Voltage Changes Table D-8 Voltage dip classifications Detection of Interruptions of the Supply VoltageTable D-9 Voltage interruptions Duration t seconds Table D-10 Over-voltages Duration t seconds Resetting Statistics Operation with PQ Advanced EnabledHarmonic Calculations Time Intervals 100 Schneider Electric. All Rights Reserved Table D-12 Portal Register Descriptions Size Data Portal Registers101 Detection and Classification of Supply Voltage Dips on 102 Schneider Electric. All Rights Reserved Detecting and Classifying Temporary Power Frequency Over 103 Alarms Allocated for PQ Advanced Evaluations Setting Up PQ Advanced Evaluation from the Display Terms Glossary63230-500-225A2 3/2011 105 106 Schneider Electric. All Rights Reserved 2011 Glossary Abbreviations and Symbols107 108 Schneider Electric. All Rights Reserved Index PowerLogicTM Series 800 Power Meter Index63230-500-225A2 3/2011 109 110 111 PLC 112 VARPage PowerLogic Power Meter 800 User Guide