Installation Requirements | Sharp AR-287 instruction

CHAPTER1 GETTING STARTED Installation requirements

INSTALLATION REQUIREMENTS

To ensure safety and proper machine performance, please note the following before initial installation and whenever the machine is to be relocated.

1.The copier should be installed near an accessible power outlet for easy

connection.

2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

3. Do not install the machine where it is: ● damp or humid,

● exposed to direct sunlight, ● extremely dusty,

●poorly ventilated,

●subject to extreme temperature or humidity changes (e.g., near an air

conditioner or heater).

4.Since a hard disk drive is built into this copier, place the copier on a firm, level surface. Choose an area which is not subject to any vibration.

5. Be sure to allow the required space around the machine for servicing and proper ventilation.

23-5/8"

(60 cm)

A small amount of ozone is produced within the copier during operation. The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration. However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

11-13/16"

(30 cm)

11-13/16"

(30 cm)

23-5/8"

(60 cm)

1-2

Image 6

Sharp AR-287 manual Installation Requirements

Contents

AR-287 AR-337 AR-407 For Your Records Contents Using this Manual Introduction Chapter Installation Requirements Getting Started Cautions Safety Precautions Power on and OFF Power save modes Power on and OFF Auto power shut-off modePreheat mode Press the Information key in the standby mode Information Function Using the Touch Panel How to use the touch panelSelection of function If multiple special functions are selected, up to six icons Function setting iconsCan be easily called by pressing its icon Will be displayedPage Making Copies Special Papers manual feed For setting the auditing mode Auditing Accounts Using the Radf Stream feeding mode Use the 10-key pad to enter the desired number Copies Using the RadfSided copies of 1-sided originals Press the Start key Sided copies from 1-sided originals Press the 2-SIDED Copy keyPress the key on the touch panel Sided copies from 2-sided originals Sided Copy Ready to COPY.DOCUMENT Feeder Mode Close the document feeder cover Making Copies Copying from Copying from the Document Glass Remove the first original with the next original after Auto REDUCTION/ENLARGEMENT/ZOOM Automatic selection REDUCTION/ENLARGEMENT/ZOOM Manual selection 129 % Set the number of copies Insert the copy paper all the way into the bypass trayThen select the bypass tray Press the Paper Select key on the touch panel Close the document cover Two-sided copying with bypass trayMake a copy Replace the first original with the second original Exposure Adjustments AutomaticText, text/photo, and photo SORT/GROUP Sort modeGroup mode Tray Press the Program key JOB MemoryStoring a job program Press the STORE/DELETE key on the touch panel JOB Memory Deleting a stored job programRecalling a job program Interrupting a Copy RUN Press the Interrupt key Special Functions XY Zoom Elect Use the reduction, enlargement, and Zoom XY ZoomPress the Y key Keys to change the copy ratio in the vertical Y direction Margin Shift Press the Special Modes keyPlace the original in the document feeder tray or on Press the Margin Shift key on the touch panel Select the desired shift amounts using the and 5 keysMargin Shift Select the shift direction Erase Press the Erase key on the touch panel Erase Select the desired erase modeAdjust the amount of edge erase and/or center erase if Needed Dual page Copying Dual Copy Dual page Copying Ensure that the desired tray is selected Multi Shot Multi Shot Press the upper OK key Enter the desired number of copies Covers Place the originals in the document feeder trayPress the Covers key on the touch panel Press the upper OK key Select cover placementCovers Enter the desired number of copies and press the Start key Transparency Film with Insert Sheets Press the Transparency Inserts key on the touch panel Transparency Film with Insert Sheets Make all other selections and press the Start keyEnsure that the desired tray is selected for insert sheets Pamphlet Copy Place the originals in the document feeder tray or on Select the type of originals Pamphlet CopyPress the Pamphlet Copy key on the touch panel Select the binding position URE Check the copy paper selection Image Editing Functions JOB Build Press the Image Edit key Make all other desired copy mode selections and enterImage Editing Functions Press the JOB Build key Centering After the first section of original pages has been fed Press the Centering key Press the Image Edit key on the touch panel Repeat Copy Select the desired copy paper size Sheet of copy paperPress the Repeat Copy key on the touch panel Cancel OK Border Line Press the Image Edit key on the touch panel Press the B/W Reverse key on the touch panel Centering E F Press the Binding Change key on the touch panel Desired number of copies Text Stamp Date Select the desired date format on the touch panel Text StampPress the Text Stamp key on the touch panel Select the pages to be stamped Select the print direction Press the Select Stamp key on the touch panel Adjust the darkness of the background of the stamp Select the stamp positionSelect the desired stamp to be printed Cancel OK Position Draft Press the Watermark key on the touch panel To adjust the exposure, press the Option keyAdjust the darkness of the watermark Select the desired watermark to be printed Cancel OK 11Press the upper OK key Number Press the page Number key on the touch panel Select the desired page number formatSelect the starting page number OK 9 Press the upper OK key Replace the finished original with the next original after Tandem Copy Press the Tandem Copy key on the touch panel Copier is installed in the sub copier Tandem CopyOn the main copier, press the Start key Example Setting ReviewPress the Review key To exit the review screen, press the Exit key Supplies Paper Types and sizes of copy paperLoading copy paper Paper Loading paper in paper trays 1Push the paper tray firmly back into the copier Changing the copy paper size in the tray Load copy paper into the tray Adding Toner Adding Toner Place the new toner cartridge with the tabs Notches as shown Used Toner Disposal Open the toner collecting container coverDisengage and remove the container from the copier Store the supplies in a location that is Storage of SuppliesProper storage Store copy paper in the wrapper and lying flat Chapter Misfeed Removal Misfeed Removal Misfeed in the bypass tray Misfeed in paper trays 1 Misfeed in the transport area Misfeed around the fusing unit and exit area Close the exit area cover Misfeed in the duplex module Remove the misfed paper from the section below the exit area Maintenance Required Troubleshooting Troubleshooting Self-diagnostic functionPage General Information Part Names and Functions Part Names and Functions Function setting icons p.1-9 Interrupt key and indicator pStart key and indicator LCD touch panel Sided Copy key Custom Settings keyInitial settings Output key User Maintenance Document glass and document cover Touch Panel Contrast Adjustment Press the Custom Settings key Specifications Copier Specifications Document FeederPage Optional Equipment System Configuration Specifications Finisher AR-FN1NPart Names Finisher AR-FN1N Offset modeNON-OFFSET mode Offset stack Staple Sort mode Sort and group Using the Radf Staple sort Staple Sort Sort Group Select the desired stapling position Using the document glass Remove the finished original with the next original after Start key indicator lights up, and then pressScanned Start key. Repeat this step until all originals have been Staple cartridge replacement Remove the rear paper and tape from the cartridge 10Push the finisher toward the copier and latch it in place Staple jam removal Push the finisher toward the copier and latch it in place Misfeed removal Misfeed in the upper transport area Close the top cover Cover of the paper feed area and open the top cover Misfeed in the lower transport area Confirm that the misfeed display is cleared Close the transport Close the paper transport area cover Finisher AR-FN2 Finisher AR-FN2 See next page for details Set the originals in the document feeder tray Press the OK key Using the document glass Exposure Paper Select Copy Ratio Close the stapler cover Push the new staple cartridge in until it clicks in placeStapler will strike three times without stapling and feed Cartridge Check that the first staple of the cartridge is at the tip Misfeed removal Push the finisher toward the copier and latch it 10place Large Capacity Tray AR-LC1N Fan the copy paper When the button lamp goes out, pull the paper tray outLarge Capacity Tray AR-LC1N Load the paper onto the feed table Release lever Gently push the tray back into place STAND/500-SHEET Paper Drawer AR-DE1N STAND/500-SHEET Paper Drawer AR-DE1N Open the lower right side cover and remove any misfed paper Dual Tray Output Unit AR-TR1 Dual Tray Output Unit AR-TR1 Page Sharp Corporation