Function

< Standard network connection >

Support

tool

n — 2

n — 1

 

 

 

n

 

 

 

 

 

n + 1

 

n + 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ME-NET

Writing data (change program) during operation of the PC is not available for hazard prevention reasons. Stop operation of the PC prior to writing data.

The operations below using a peripheral device, that is connected to a "n" station, is possible.

-Change programs

-Monitor

-Change parameter memory (only by using JW-14PG/13PG/12PG)

< Expansion network connection >

Support

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tool

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

n — 2

n — 1

 

 

 

n

 

 

n + 1

*n + 2 m m + 1 m + 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ME-NET* The JW-21MN is unusable as a junction station ("n + 2" station and "m" station in the figure above). Use

JW30H (JW-21MN), JW50H/70H/100H (JW-21MN).

 

The operations below using a peripheral device, that is connected to a "n" station, is possible.

 

- Change programs

 

Writing data (change program) during operation of the

 

 

 

 

 

 

 

- Monitor

 

 

 

 

 

PC is not available for hazard prevention reasons. Stop

 

 

 

- Change parameter memory

 

operation of the PC prior to writing data.

 

 

 

(only by using JW-14PG/13PG/12PG)

 

 

 

 

 

 

 

 

 

 

Operation example

 

 

 

 

 

This paragraph describes an operation example using the multipurpose programmer: JW-50PG.

 

For operations with other support tools, see the attached instruction manuals.

 

- Connect the JW-50PG to the JW-21MN on the ME-NET.

16

- Set communication mode

 

 

 

 

 

 

 

 

 

 

Set the communication mode of the JW-50PG to "Network CONCT." and this enables remote programming and remote monitor.

Select "Initial setting."

Select "COM. set."

(JW-50PG)

Select "Network CONCT."

(JW-21MN)

16-14