11-4 Setting slave station parameters (common for all slave stations)
When the
[1] Setting contents
|
|
|
| Setting item |
|
| Initial | Contents | Corresponding | ||||
|
|
|
|
| Address(8) | signs on pages | |||||||
|
|
|
|
| value (H) | ||||||||
|
|
|
|
| |||||||||
|
|
|
| Number of receiving bytes of |
|
| Set the number of bytes by decimals. (0 to 256) |
|
|
| |||
|
|
| ① | relay link in save memory |
| 007720 | 00 | - If 0 is set, the number of bytes will be the same | h1 to hn | ||||
|
|
| function |
| 007721 | as the number of the sending bytes which is set | |||||||
|
|
|
|
| V2 |
| in the master station |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
| *1 |
|
|
|
|
|
|
|
|
| |||
|
|
| Number of receiving bytes of |
|
| Set the number of bytes by decimals. (0 to 2048) |
|
|
| ||||
|
|
|
|
|
|
|
|
| |||||
|
|
| ② | register link in save memory | 007722 | 00 | - If 0 is set, the number of bytes will be the same | i1 to in | |||||
|
|
| function |
| 007723 | as the number of the sending bytes which is set | |||||||
|
|
|
|
| V2 |
|
| in the master station |
|
|
|
| |
*2 | ③ | Whether the station number |
| 00 | Store the number of own statin in the data memory |
|
|
| |||||
information should be output | 007763 | when setting on 01(H). (storage area of 1 byte follows |
|
|
| ||||||||
|
|
| |||||||||||
|
|
|
| or not | V2 |
|
| flag area of 24 bytes, valid when 007767(8) is 80(H)) |
|
|
| ||
|
|
|
|
|
| 007764 | E0 | Lower of file address |
| Initial value: 01E0(H) |
|
|
|
|
|
|
| Top address of flag area |
| 007765 | 01 |
|
| ↓ |
|
|
|
|
|
| ④ |
| Upper of file address |
| 000740(8) (コ0740) | e1 to en | |||||
|
|
| (communication and PC |
|
| ||||||||
|
|
|
|
| 00 |
|
|
| |||||
|
|
|
| operation condition monitor | 007766 | File number |
|
|
|
| |||
|
|
|
| flag) |
| 007767 | 80 | Flag output (Yes: 80(H) No: 00(H)) |
|
|
| ||
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| 00(H): Stop operation |
|
|
|
| |
|
|
|
| - Start/stop operation of the |
|
| 01(H): Start operation |
|
|
|
| ||
|
|
| ⑤ |
| 007777 | 01 | 80(H): Writing to the EEPROM, stop operation |
|
|
| |||
|
|
| - Writing to EEPROM of the |
|
|
| |||||||
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 81(H): Writing to the EEPROM, start operation |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| 08(H): Parameter initializing |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*1: Set only when the memory capacity save function is used.
| *2: "Whether the station number information should be output or not" is a unique function of the | ||
11 | |||
| |||
| - | Parameter addresses other than above mentioned are reserved areas and prohibited to be | |
| |||
|
| changed. | |
- | When any slave stations are except |