Maintenance Indicators
■The warning lights on the projector indicate problems inside the projector.
■If a problem occurs, either the TEMPERATURE WARNING indicator or the LAMP REPLACEMENT indicator will illuminate red, and the power will turn off. After the power has been turned off, follow the procedures given below.
| TEMPERATURE |
| WARNING |
POWER | indicator |
indicator | LAMP |
| |
| REPLACEMENT |
| indicator |
About the TEMPERATURE WARNING indicator
If the temperature inside the projector in- creases, due to blockage of the air vents, or
the setting location, “
” will blink in the lower left corner of the picture. If the tem- perature keeps on rising, the lamp will turn off and the TEMPERATURE WARNING in- dicator will blink, the cooling fan will run for further 90 seconds, then the power will be
shut off. After “
” appears, be sure to perform the following measures.
About the
LAMP REPLACEMENT indicator
■When the lamp
exceeds 1,900 cumulative hours
of use, “
” will be displayed on the screen in yellow. When
the cumulative hours of use
reach 2,000, “
” will change to red, the lamp will au- tomatically turn off and then the projector as well. At this time, the LAMP REPLACEMENT indica- tor will illuminate in red.
■If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
| Maintenance indicator | Condition |
| Problem |
| Possible Solution | |||
|
|
|
|
|
|
|
|
|
|
|
| Normal | Abnormal |
| • | Blocked air intake | • | Relocate the projector to an area | |
| TEMPERA- |
|
| The internal |
| with proper ventilation. |
| ||
|
|
|
|
|
| ||||
| TURE |
|
| • | Cooling fan break- | • | Take the projector to your nearest | ||
|
| Red on/ | temperature is | ||||||
| WARNING | Off |
| down |
| Sharp Authorized Projector Dealer | |||
|
|
|
|
| |||||
| indicator |
| Power off | abnormally high. | • | Internal circuit failure |
| or Service Center (see page 118) | |
|
|
|
|
| • | Clogged air intake |
| for repair. | |
|
|
|
|
|
|
|
|
|
|
|
| Green on | Red | Time to change | • | Lamp usage time | • | Take the projector to your nearest | |
| LAMP | Green | blinks | the lamp |
| exceeded 1,900 |
| Sharp Authorized Projector Dealer | |
| REPLACE- | blinks |
|
|
| hours |
| or Service Center (see page 118) | |
| MENT | when the |
|
|
|
|
| for repair or lamp replacement. | |
| Red on/ | The lamp does | • | • | |||||
| indicator | lamp is | Please exercise care when | ||||||
| Power off | not illuminate. | • | Lamp circuit failure | |||||
|
| active. |
| replacing the lamp. | |||||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
Info
•If the TEMPERATURE WARNING indicator illuminates, and the power turns off, follow the above possible solutions and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.)
•If the power is turned off and then turned on again, as during a brief test, the LAMP REPLACEMENT indica- tor may be triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and plug it back in again.
•If you want to clean the air vents during projector operation, be sure to first press 
and after the power has turned off and the cooling fan has stopped, then clean the vents.
•Do not unplug the power cord after the power has been turned off and while the cooling fan is running. The cooling fan runs for about 90 seconds.
-110
-110110 | 02.4.29, 3:25 PM |
