Removing a Paper Jam | Sharp XE-A212 guide

A212_5 OPERATOR MAINTENANCE 03.7.5 7:53 AM Page 77

7.Insert the end of the paper into the slit in the spool. (Press the F

key to feed more paper if required.)

8.Wind the paper two or three turns around the spool shaft.

9. Set the spool on the bearing, and press the Fkey to take up excess slack in the paper.

10. Replace the printer cover.

You can wind the roll paper in OP X/Z, X1/Z1, and X2/Z2 modes even if you programmed so that the printer is used for issuance of receipts. This may be convenient to wind reports. In this case, set the roll paper to the take- up spool.

6Removing a Paper Jam

Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself. Never touch the print head immediately after printing, as the head may still be hot.

1.Remove the printer cover.

2.Lift up the print roller release lever to unlock and open the print roller arm.

3.Remove the paper jam. Check for and remove any shreds of paper that may remain in the printer.

4.Reset the paper roll correctly by following the steps in “Installing the paper roll”.

7Cleaning the Printer (Print Head / Sensor / Roller)

When the printed text is getting dark or faint, paper dust may be stuck to the print head, sensor and/or roller. Clean them as follows:

Caution:

•Never touch the print head with a tool or anything hard as it may damage the head.

•The paper cutter is mounted on the printer cover. Be careful not to cut yourself.

Print head

1. Turn the mode switch to the “ ” position.

2.Remove the printer cover.

3.Lift up the print roller release lever to unlock and open the print roller arm.

4.Remove the paper roll referring to the “Removing the

		5.	paper roll” section.
		5.	Clean the print head with a cotton swab or soft rag
			moistened with ethyl alcohol or isopropyl alcohol. Clean
		6.	the roller and the sensor in the same manner.
Roller	Sensor	6.	Reset the paper roll correctly by following the steps in
			“Installing the paper roll”.

77

Image 79

Sharp XE-A212 instruction manual Removing a Paper Jam, Cleaning the Printer Print Head / Sensor / Roller

Contents

XE-A212 Aviso Never operate the register with wet hands IntroductionU T I O N For Easy Set-up, see Getting Started Contents Basic Function Programming For Quick Start Correction After Finalizing a Transaction Void mode External View Front view Parts and Their FunctionsPrinter Key names Mode Switch and Mode KeysKeyboard Keyboard layout Keyboard sheet Customer display Pop-up type Displays Operator displayDrawer Lock Key How to remove the register from the fixing angle bracket How to install the fixing angle bracketGetting Started Be careful with the paper cutter, so as not to cut yourself Initializing the cash register Installing a paper roll When using the take-up spool using as journal paper When not using the take-up spool using as receipt paperDate Time VAT/tax Rounding system Decimal point position tab setting for domestic currency 2300 Basic Sales EntryBasic Sales Entry Example 1500 Error Warning PLU entries When using the department keys for department 1 toWhen using the department code entry key Item Entries Single item entries Repeat entries $ $Multiplication entries @ 50 d 1500 d @ 41 d @ 80 p @ 500 ﬁ @ 85 p 1200 p @ $Single item cash sale Sics entry PLU level shift for direct PLU key Lock shift mode Automatic return mode Cash or cheque sale that does not require tender entry 300Displaying Subtotals Finalization of Transaction Cash or cheque tendering Computation of VAT Value Added Tax/tax VAT/ tax system 950 a bCredit sale Mixed-tender sale Automatic VAT 1 and automatic tax 2-4 system Optional Features10 % Auxiliary Entries Percent calculations premium or discount Refund entries 800 5 %575 100 Deduction entries 1230 N 1500 250 f 41 fd 100 d 85 fp 150 pNon-add code number entries and printing Guest Look-up GLU 11 G a 11 G1400 1600 2300 4650 d Auxiliary Payment Treatment Currency exchange4650 d 10000 a Automatic Sequence Key a key Entries Received-on account entriesPaid-out entries No sale exchange 328 ª CorrectionCorrection of the Last Entry direct void 1310 1755 Subtotal Void Prior to Programming Procedure for programmingGuidance messages 10 d 29 @200 Guidance for text programming Using character keys Keys on the shaded areaOperator display Example Hijk01 Alphanumeric character code table 231 Tax Programming Basic Function ProgrammingDate and Time Programming Time Tax rate programming 12 sKey operation example Print Department Programming Auxiliary Function ProgrammingDepartment status Abcdefgh 00011183 @ Preset unit pricePLU Price Look-Up and Subdepartment Programming Direct PLU key programming For PLU code 1 to Key operation Operator display Specify the direct PLU key and its level Associated dept. programming Press sto skip Unit price and associated department assignmentFunction programming Press sto skip Rate for % 200 p 125 #PLU/subdepartment selection Miscellaneous Key Programming Function parameters for % 10 P 25 %Amount for Percent rate limitation for % 102 @ Function parameters forFunction parameters for r, o, X, Y, c, b and a 1006 @ Department text item label 16 digits Text Programming018 @ Apple s PLU text item label 16 digitsFunction text 12 digits Fruit s NET2 List of function texts David s Clerk names 12 digitsLogo message print format 3 types US S $ Foreign currency symbol 4 digitsDomestic currency symbol 4 digits S s a Register number Training mode text 12 digitsAdvanced Function Programming Register Number and Consecutive Number Programming Job code Selection Entry Various Function Selection ProgrammingFunction selection for miscellaneous keys 00000100 s a Receipt print format Print formatPrinting style Other programming PLU level shift and GLU function parameters Job code Selection Entry Compression print on journal A2123 for the Manager 03.9.8 457 PM Action when EJ memory area is full PGM mode operation records typeTemporary EJ printing during a transaction 11 @ Power save modeLogo message print format 10 @ 0060 s a Language selection Thermal printer densityEJ memory type 100 Training clerk specification for training modeAuto key programming Automatic sequence key 86 @ 20 s a Euro Programming Euro system settingsAutomatic Euro modification operation settings 01 s 14 @ 10 s Date setting for Euro modification operationTime setting for Euro modification operation 13 @ 01072005 s Programming report Reading Stored ProgramsKey sequence for reading stored program Sample printouts Printer density programming report Programming report Department programming reportPLU programming report Auto key programming report Training Mode Summary of Reading X and Resetting Z Reports Reading X and Resetting Z of Sales Totals Sample report Daily Sales Totals Full sales report Individual clerk report PLU report by designated rangeFull clerk report Periodic Consolidation Full sales report Hourly reportOpen GLU report Open GLU report by clerk Balance report Sample EJ report EJ Report Reading and ResettingPrinting journal data on the way of a transaction Sample print Override Entries Incorrect receipt Cancellation receipt250 Period Euro Migration Function Euro status Items Cheque/credit operation Optional Programming for the Introduction of EuroCurrency exchange rate Exchange rate entry selection Case of Power Failure Operator MaintenanceCase of Printer Error Replacing the Paper Roll Paper specificationHow to set the paper roll Replacing the Batteries Removing the paper roll Installing the receipt paper roll Installing the paper rollInstalling the journal paper roll Removing a Paper Jam Cleaning the Printer Print Head / Sensor / Roller Opening the Drawer by Hand Removing the Till and the Drawer Protection de l’environnement BLUENeutral BROWNLiveEnvironment Protection Umweltschutz Sharp Corporation