Address Table Commands, Action | SMC Networks SMC8150L2 specification

4 Command Line Interface

Address Table Commands

These commands are used to configure the address table for filtering specified addresses, displaying current entries, clearing the table, or setting the aging time.

Table 4-51 Address Table Commands

Command	Function	Mode	Page
mac-address-table static	Maps a static address to a port in a VLAN	GC	4-140

clear mac-address-table	Removes any learned entries from the forwarding database	PE	4-141
dynamic
show mac-address-table	Displays entries in the bridge-forwarding database	PE	4-141

mac-address-table	Sets the aging time of the address table	GC	4-142
aging-time
show mac-address-table	Shows the aging time for the address table	PE	4-143
aging-time

mac-address-table static

This command maps a static address to a destination port in a VLAN. Use the no form to remove an address.

Syntax

mac-address-table static mac-addressinterface interface vlan vlan-id[action]

no mac-address-table static mac-addressvlan vlan-id

•mac-address- MAC address.

•interface

•ethernet unit/port

-unit - Stack unit. (Always unit 1)

-port - Port number. (Range: 1-26/50)

•port-channel channel-id(Range: 1-32)

•vlan-id- VLAN ID (Range: 1-4094)

•action -

-delete-on-reset- Assignment lasts until the switch is reset.

-permanent - Assignment is permanent.

Default Setting

No static addresses are defined. The default mode is permanent.

Command Mode

Global Configuration

4-140

Page 382

Image 382

SMC Networks SMC8150L2 manual Mac-address-table static, Address Table Commands Function Mode, Action

Contents

Management Guide Page TigerSwitch 10/100/1000 Management Guide Page Contents Page Iii Page Command Line Interface Page Vii Viii Contents Page Contents Xii Glossary Index Appendix a Software SpecificationsAppendix B Troubleshooting Xiii Xiv Tables Xvi Xvii Xviii Figures Xix Figures Xxi Xxii Key Features Key FeaturesFeature Description Description of Software Features Introduction Description of Software Features Introduction Description of Software Features System Defaults System DefaultsFunction Parameter Default System Defaults Function Parameter Client Enabled Sntp Connecting to the Switch Configuration Options Initial Configuration Required Connections Remote Connections Basic ConfigurationConsole Connection Setting an IP Address Setting PasswordsManual Configuration Dynamic Configuration Enabling Snmp Management Access Trap Receivers Saving Configuration Settings Configuring Access for Snmp Version 3 Clients Managing System Files Initial Configuration Configuring the Switch Using the Web Interface Navigating the Web Browser Interface Home Button Configuration Options ActionPanel Display Revert Apply Help Main Menu Description Main MenuSystem System Information Configuration Allows ports to dynamically join trunks ACL STA 116 Current Table Class-of-service value122 131 Configuration Settings Query Igmp Filter ConfigurationConfiguration Settings Igmp Filter/Throttling Trunk 152 Cache Dhcp Snooping 186 Configuration183 185 Displaying System Information Field Attributes Main Board Displaying Switch Hardware/Software VersionsCLI Specify the hostname, location and contact information Management Software Web Click System, Switch Information Switch Information Bridge Extension Configuration Displaying Bridge Extension Capabilities CLI Enter the following command Setting the Switch’s IP AddressCommand Attributes Manual IP Configuration Using DHCP/BOOTP Dhcp IP Configuration Enabling Jumbo Frames Managing Firmware Downloading System Software from a Server Copy Firmware Saving or Restoring Configuration Settings 11 Deleting Files Downloading Configuration Settings from a Server 12 Downloading Configuration Settings for Startup Console Port Settings 13 Setting the Startup Configuration Settings 14 Console Port Settings Telnet Settings 15 Enabling Telnet Configuring Event Logging Displaying Log Messages CLI This example shows the event message stored in RAM System Log ConfigurationError resource exhausted Logging Levels Remote Log Configuration 17 System Logs Simple Mail Transfer Protocol 18 Remote Logs 19 Enabling and Configuring Smtp Resetting the System Renumbering the System Setting the System Clock Configuring Sntp Setting the Time Zone 23 Setting the System Clock Access Mode Setting Community Access StringsSimple Network Management Protocol 24 Configuring Snmp Community Strings Specifying Trap Managers and Trap Types 25 Configuring IP Trap Managers Enabling Snmp Agent Status Setting the Local Engine ID Configuring SNMPv3 Management AccessCLI This example sets an SNMPv3 engine ID Specifying a Remote Engine ID Configuring SNMPv3 UsersCLI This example specifies a remote SNMPv3 engine ID Configuring the Switch 29 Configuring SNMPv3 Users Configuring Remote SNMPv3 Users 30 Configuring Remote SNMPv3 Users Supported Notification Messages Configuring SNMPv3 GroupsTopology Change Timer immediately Subsequent to its election SNMPv2 Traps Rmon Events Mode PethPsePortPower 6.1.4.1.202.20.68.2.1.0.1 Private Traps SwPowerStatus 6.1.4.1.202.20.68.2.1.0.1PD Powered Device. This notification is ChangeTrap SwIpFilterRejectTrap 6.1.4.1.202.20.68.2.1.0.1 31 Configuring SNMPv3 Groups Setting SNMPv3 Views 32 Configuring SNMPv3 Views User Authentication Configuring User Accounts 33 Access Levels Configuring Local/Remote Logon Authentication Command Usage Radius Settings Tacacs Settings 34 Authentication Settings User Authentication Configuring Https Https System Support Web Browser Operating System Replacing the Default Secure-site Certificate Configuring the Secure Shell User Authentication Configuring the SSH Server SSH server includes basic settings for authentication Generating the Host Key Pair 37 SSH Host-Key Settings Configuring Port Security Configuring 802.1X Port Authentication 38 Configuring Port Security Displaying 802.1X Global Settings 802.1X protocol provides client authentication CLI This example enables 802.1X globally for the switch Configuring 802.1X Global SettingsCLI This example shows the default global setting for Web Click Security, 802.1X, Information Configuring Port Settings for Authorized 41 802.1X Port Configuration Consoleconfig#interface ethernet 1/2 802.1X Statistics Displaying 802.1X StatisticsParameter Description Configuring Access Control Lists Access Control ListsCLI This example displays the 802.1X statistics for port Setting the ACL Name and Type CLI This example creates a standard IP ACL named david Configuring a Standard IP ACL Configuring an Extended IP ACL Configuring the Switch 45 Configuring Extended IP ACLs Configuring a MAC ACL Binding a Port to an Access Control List This switch supports ACLs for ingress filtering only Filtering IP Addresses for Management Access 47 Configuring ACL Port Binding 48 Creating an IP Filter List Displaying Connection Status Port ConfigurationCLI This example allows Snmp access for a specific client Field Attributes Web Web Click Port, Port Information or Trunk Information ConfigurationBasic Information Configuring Interface Connections Current Status 50 Port/Trunk Configuration Creating Trunk Groups Statically Configuring a Trunk 51 Configuring Static Trunks Enabling Lacp on Selected Ports 131 52 Lacp Trunk Configuration Configuring Lacp Parameters Dynamically Creating a Port Channel 53 Lacp Port Configuration Lacp Port Counters Displaying Lacp Port CountersYou can display statistics for Lacp protocol messages Field Description 54 Lacp Port Counters Information CLI The following example displays Lacp counters Displaying Lacp Settings and Status for the Local Side Lacp Internal Configuration Information 55 Lacp Port Internal Information Displaying Lacp Settings and Status for the Remote Side Lacp Neighbor Configuration Information Field Description Setting Broadcast Storm Thresholds 57 Port Broadcast Control Configuring Port Mirroring 58 Mirror Port Configuration Configuring Rate Limits Rate Limit Configuration Showing Port Statistics 10 Port Statistics Etherlike Statistics Resources Jabbers Or alignment error Received BytesRmon Statistics Drop Events Formed Oversize Frames 60 Port Statistics Setting Static Addresses Address Table SettingsCLI This example shows statistics for port 61 Configuring a Static Address Table Displaying the Address Table 62 Configuring a Dynamic Address Table Changing the Aging Time Spanning Tree Algorithm ConfigurationCLI This example sets the aging time to 300 seconds Spanning Tree Algorithm Configuration 104 Displaying Global Settings 64 Displaying Spanning Tree Information Configuring Global Settings Global settings apply to the entire switch Basic Configuration of Global Settings Root Device Configuration Configuration Settings for Rstp Configuration Settings for Mstp 65 Configuring Spanning Tree Displaying Interface Settings 112 66 Displaying Spanning Tree Port Information CLI This example shows the STA attributes for port Configuring Interface Settings 67 Configuring Spanning Tree per Port CLI This example sets STA attributes for port Configuring Multiple Spanning Trees 68 Configuring Multiple Spanning Trees Displaying Interface Settings for Mstp MST Instance ID Instance identifier to configure. Default 69 Displaying Mstp Interface Settings Configuring Interface Settings for Mstp 121 Ieee 802.1Q VLANs Vlan ConfigurationCLI This example sets the Mstp attributes for port Assigning Ports to VLANs 124 CLI This example enables Gvrp for the switch Enabling or Disabling Gvrp Global SettingForwarding Tagged/Untagged Frames Displaying Basic Vlan Information Command Attributes WebDisplaying Current VLANs 73 Displaying Current VLANs Command Attributes CLI Creating VLANs 175 Adding Static Members to VLANs Vlan Index CLI This example creates a new Vlan 130 75 Configuring a Vlan Static Table Adding Static Members to VLANs Port Index Configuring Vlan Behavior for Interfaces Configuring Ieee 802.1Q Tunneling 77 Configuring VLANs per Port Layer 2 Flow for Packets Coming into a Tunnel Access Port Layer 2 Flow for Packets Coming into a Tunnel Uplink Port Configuration Limitations for QinQ General Configuration Guidelines for QinQ Enabling QinQ Tunneling on the Switch 78 802.1Q Tunnel Status CLI This example sets the switch to operate in QinQ mode Adding an Interface to a QinQ Tunnel 79 Tunnel Port Configuration 45-1 CLI This example enables private VLANs Configuring Private VLANsEnabling Private VLANs Protocol Vlan Group Configuration Configuring Uplink and Downlink PortsProtocol VLANs Configuring Protocol Vlan Interfaces 82 Protocol Vlan Configuration Layer 2 Queue Settings Class of Service ConfigurationSetting the Default Priority for Interfaces Mapping CoS Values to Egress Queues Port Priority ConfigurationCLI This example assigns a default priority of 5 to port 11 Mapping CoS Values to Egress Queues Background 12 CoS Priority LevelsPriority Level Traffic Type Spare Selecting the Queue Mode Enabling CoS Setting the Service Weight for Traffic Classes 87 Queue Mode Mapping Layer 3/4 Priorities to CoS Values Layer 3/4 Priority SettingsSelecting IP Precedence/DSCP Priority Mapping IP Precedence 13 Mapping IP Precedence 90 Mapping IP Precedence Priority Values IP Dscp Value CoS Value Mapping Dscp Priority14 Mapping Dscp Priority Values 10, 12, 14 18, 20, 22 26, 28, 30, 32, 34 38, 40 Mapping IP Port Priority 92 IP Port Priority Status Quality of Service 93 IP Port Priority Configuring a Class Map Configuring Quality of Service ParametersClass map is used for matching packets to a specified class Match Class Settings Class ConfigurationClass Map 94 Configuring Class Maps Creating QoS Policies Policy ConfigurationPolicy Map Policy Rule Settings Class Settings Policy Options 95 Configuring Policy Maps 96 Service Policy Settings Attaching a Policy Map to Ingress Queues Multicast Filtering Layer 2 Igmp Snooping and Query Configuring Igmp Snooping and Query Parameters 97 Igmp Configuration Enabling Igmp Immediate Leave Displaying Interfaces Attached to a Multicast Router 98 Igmp Immediate Leave Specifying Static Interfaces for a Multicast Router 99 Displaying Multicast Router Port Information Displaying Port Members of Multicast Services 100 Static Multicast Router Port Configuration Assigning Ports to Multicast Services 101 IP Multicast Registration Table Igmp Filtering and Throttling 102 Igmp Member Port Table Enabling Igmp Filtering and Throttling 103 Enabling Igmp Filtering and Throttling Configuring Igmp Filtering and Throttling for Interfaces Configuring Igmp Filter Profiles 104 Igmp Filter and Throttling Port Configuration 105 Igmp Profile Configuration Multicast Vlan Registration Configuring Global MVR Settings General Configuration Guidelines for MVR 106 MVR Global Configuration Displaying MVR Interface Status Web Click MVR, Port or Trunk Information 107 MVR Port Information Displaying Port Members of Multicast Groups 108 MVR Group IP Information Configuring MVR Interface Status MVR Vlan Web Click MVR, Port or Trunk Configuration Assigning Static Multicast Groups to Interfaces Configuring Domain Name Service Configuring General DNS Service Parameters 111 DNS General Configuration Configuring Static DNS Host to Address Entries 238 112 DNS Static Host Table Displaying the DNS Cache 113 DNS Cache Dhcp Snooping Dhcp Snooping Configuration Web Click Dhcp Snooping, Configuration Enables Dhcp snooping on the specified Vlan Dhcp Snooping Vlan ConfigurationDhcp Snooping Information Option Configuration CLI This example first enables Dhcp Snooping for Vlan Dhcp Snooping Port Configuration Trust Status Enables or disables port as trusted 117 Dhcp Snooping Port Configuration Dhcp Snooping Binding Information IP Source Guard IP Source Guard Port ConfigurationWeb Click Dhcp Snooping, Dhcp Snooping Binding Information Static IP Source Guard Binding Configuration 119 IP Source Guard Port Configuration 120 Static IP Source Guard Binding Configuration Dynamic IP Source Guard Binding Information Switch Clustering Web Click IP Source Guard, Dynamic Information Cluster Configuration 122 Cluster Member Choice Web Click Cluster, Configuration Cluster Member ConfigurationAdds Candidate switches to the cluster as Members Displays current cluster Member switch information Web Click Cluster, Member ConfigurationCluster Member Information Cluster Candidate Information 126 Cluster Candidate Information Using the Command Line Interface Accessing the CLI Telnet Connection Getting Help on Commands Entering CommandsCommand Completion Keywords and Arguments Showing Commands Understanding Command Modes Negating the Effect of CommandsUsing Command History Partial Keyword Lookup Exec Commands Command Modes Configuration Modes Command Prompt Configuration CommandsConsoleconfig-if# 120 Command Line Processing Command Line ProcessingKeystroke Function Command Groups Command Groups Description Line Commands Line Commands Function Mode Login Line Syntax Password 0 7 password no password PasswordUsername 4-25 password No password is specified Timeout login response Exec-timeout Syntax Exec-timeout seconds no exec-timeout Password-threshSyntax Password-thresh threshold no password-thresh Databits Silent-timeSyntax Silent-time seconds no silent-time Syntax Databits 7 8 no databits ParitySyntax Parity none even odd no parity Syntax Speed bps no speed SpeedStopbits Syntax Stopbits 1 Syntax Disconnect session-id DisconnectShow line Syntax Show line console vty To show all lines, enter this command General CommandsEnable General Commands Function Mode Enable DisableDisable Enable password Level Configure Show history Reload End Exit This command exits the configuration programThis example shows how to quit a CLI session Quit Device Designation Commands System Management CommandsPrompt Hostname User Access CommandsUser Access Commands Function Mode Username 10 Default Login Settings Username Access-level Password Enable passwordGuest Admin 11 IP Filter Commands Function Mode IP Filter CommandsManagement Show management All addresses Default Setting Command Mode Web Server Commands12 Web Server Commands Function Mode Ip http port Ip http server Syntax No ip http server Default SettingSyntax No ip http secure-server Default Setting Ip http secure-server Ip http secure-port4-31 Copy tftp https-certificate Ip http secure-port13 Https System Support Web Browser Operating System Portnumber The UDP port used for HTTPS. Range Ip telnet port Telnet Server Commands14 Telnet Server Commands Function Mode Ip http secure-server4-30 15 SSH Commands Function Mode Secure Shell CommandsSyntax No ip telnet server Default Setting Ip telnet server Copy tftp public-key Syntax No ip ssh server Default Setting Ip ssh server Exec-timeout4-13 show ip ssh Ip ssh timeoutSyntax Ip ssh timeout seconds no ip ssh timeout Ip ssh crypto host-key generate 4-38 show ssh Key-size- The size of server key. Range 512-896 bits Ip ssh authentication-retriesIp ssh server-key size Bits Syntax Delete public-key username dsa rsa Delete public-keyIp ssh crypto host-key generate Syntax Ip ssh crypto host-key generate dsa rsa Syntax Ip ssh crypto zeroize dsa rsa Ip ssh crypto zeroizeIp ssh save host-key Syntax Ip ssh save host-key dsa rsa Show ssh This command displays the current SSH server connectionsShow ip ssh Ip ssh crypto host-key generate Terminology Show public-keySyntax Show public-key user username host Console#show public-key host Host Syntax No logging on Default Setting Event Logging Commands17 Event Logging Commands Function Mode Logging on Logging history Flash errors level 3 RAM warnings level 618 Logging Levels Syntax No logging host hostipaddress Logging hostLogging facility Hostipaddress The IP address of a syslog server Syntax Logging trap level no logging trap Logging trapClear logging Syntax Clear logging flash ram Syntax Show logging flash ram sendmail trap Show logging19 show logging flash/ram display description Syntax Show log flash ram login tail Facility commandLogging trap command Show log Logging sendmail host Smtp Alert Commands21 Smtp Alert Commands Function Mode Following example shows sample messages stored in RAM Logging sendmail level Syntax Logging sendmail level level Syntax No logging sendmail source-email email-address Logging sendmail source-emailLogging sendmail destination-email This example will set the source email john@acme.com Logging sendmail Syntax No logging sendmail Default SettingShow logging sendmail Syntax No sntp client Default Setting Time Commands22 Time Commands Function Mode Sntp client Syntax Sntp server ip1 ip2 ip3 Sntp serverSntp server 4-54 sntp poll 4-55 show sntp Sntp client 4-53 sntp poll 4-55 show sntp Syntax Sntp poll seconds no sntp poll Sntp pollShow sntp Sntp client Syntax Clock timezoneCalendar set Calendar set hour min sec day month year month day year This command displays the system clock System Status CommandsShow startup-config 23 System Status Commands Function Mode Command Line Interface Show running-config Show running-config4-59 Show startup-config4-57 Show system This command displays system informationShow users Show version Jumbo frame Enables support for jumbo frames Frame Size Commands24 Frame Size Commands Function Mode Syntax No jumbo frame Default Setting Copy Flash/File Commands25 Flash/File Commands Function Mode Copy Flash/File Commands Following example shows how to download a configuration file Delete unit filename This command deletes a file or imageDelete Dir Delete public-key4-38 26 File Directory Information Syntax Dir unit boot-rom config opcode filenameDir Column Heading Description Syntax whichboot unit WhichbootBoot system Syntax Boot system unit boot-romconfig opcode filename Dir 4-68 whichboot Authentication CommandsAuthentication Sequence 27 Authentication Commands Command Group Function Username for setting the local user names and passwords Authentication loginLocal Authentication enable Show radius-server Shows the current Radius settings 29 Radius Client Commands Function ModeRadius Client Radius-server host Default Setting Auth-portRetransmit Command Mode Radius-server port Radius-server retransmit Radius-server keySyntax Radius-server key keystring no radius-server key Radius-server timeout Show radius-server Tacacs-server host 30 Tacacs Commands Function ModeTACACS+ Client Tacacs-server port Show tacacs-server Tacacs-server keySyntax Tacacs-server key keystring no tacacs-server key Status Disabled Action None Maximum Addresses Port Security Commands31 Port Security Commands Function Mode Interface Configuration Ethernet Command Usage Syntax No dotx system-auth-control Default Setting 802.1X Port Authentication32 802.1X Port Authentication Command Function Mode Dot1x system-auth-control Dot1x max-req Dot1x defaultDefault Command Mode Dot1x port-control Force-authorized Dot1x operation-modeSingle-host Dot1x re-authentication Dot1x re-authenticateDot1x timeout quiet-period Dot1x timeout re-authperiod Dot1x timeout tx-period Syntax Show dot1x statistics interface interface Show dot1xStatistics Displays dot1x status for each port State Current state including initialize, reauthenticate Authenticator State MachineReauthentication State Machine Backend State Machine Command Line Interface Access Control Lists Access Control List Commands33 Access Control Lists Command Groups Function Syntax No access-list ip standard extended aclname Access-list ip34 IP ACLs Command Function Mode IP ACLs Syntax No permit deny any source bitmask host source Permit, deny Ip access-group4-93 show ip access-list4-93Access-list ip Standard ACL Source-port sport end destination-port dport end Any destination address-bitmask host destinationExtended ACL Syntax Show ip access-list standard extended aclname Show ip access-listIp access-group Syntax No ip access-group aclname Show ip access-list4-93 Show ip access-groupThis command shows the ports assigned to IP ACLs Syntax No access-list mac aclname Access-list mac35 MAC ACL Commands Function Mode Permit, deny Mac access-group4-98 show mac access-list4-97 Permit, deny MAC ACL Syntax Show mac access-list aclname Show mac access-listThis command displays the rules for configured MAC ACLs Permit, deny Mac access-group4-98 Syntax Mac access-group aclname Mac access-groupShow mac access-group Show mac access-list4-97 36 ACL Information Command Function Mode Show access-listShow access-group ACL Information Snmp Commands 37 Snmp Commands Function Mode Snmp-server Syntax No snmp-server Default SettingShow snmp Snmp-server community Syntax Snmp-server contact string no snmp-server contact Snmp-server contactSnmp-server location Syntax Snmp-server location text no snmp-server location Snmp-server host Host Address None Notification Type Traps Snmp Version UDP Port Snmp-server enable traps Snmp-server enable trapsIssue authentication and link-up-down traps Snmp-server engine-id This example shows the default engine ID This command shows the Snmp engine IDShow snmp engine-id Examples Defaultview includes access to the entire MIB treeSnmp-server view This view includes MIB-2 Snmp-server group This command shows information on the Snmp viewsShow snmp view 39 show snmp view display description Consoleconfig#snmp-server group r&d v3 auth write daily Show snmp group Snmp-server user 40 show snmp group display description 114 Show snmp user This command shows information on Snmp users41 show snmp user display description Interface Interface Commands42 Interface Commands Function Mode Port-channel channel-idRange Speed-duplex DescriptionSyntax Description string no description Negotiation Syntax No negotiation Default SettingNegotiation 4-118 capabilities Capabilities Following example configures port 11 to use autonegotiationCapabilities 4-119speed-duplex4-117 Flowcontrol Syntax No flowcontrol Default SettingNegotiation 4-118speed-duplex4-117 flowcontrol Syntax No shutdown Default Setting Shutdown Clear counters Switchport broadcast packet-ratePort-channel channel-idRange Default Setting Syntax Clear counters interface Following example clears statistics on port This command displays the status for an interfaceShow interfaces status Syntax Show interfaces status interface Syntax Show interfaces counters interface This command displays interface statisticsShow interfaces counters Shows the counters for all interfaces Syntax Show interfaces switchport interface Show interfaces switchportShows all interfaces 43 Interfaces Switchport Statistics Port monitor Mirror Port Commands44 Mirror Port Commands Function Mode Interface ethernet unit/port source port Show port monitor This command displays mirror informationFollowing shows mirroring configured from port 6 to port Syntax Show port monitor interface Rate-limit Rate Limit CommandsGigabit Ethernet 1000 Mbps 135 Link Aggregation Commands46 Link Aggregation Commands 123 General Guidelines Channel-groupGuidelines for Creating Trunks Dynamically Creating a Port Channel Lacp Syntax No lacp Default SettingFollowing example creates trunk 1 and then adds port Lacp system-priority 32768 Lacp admin-keyEthernet Interface Lacp admin-key Port Channel Interface Configuration Port Channel Lacp port-priority This command displays Lacp informationShow lacp Type Port Channel all47 show lacp counters display description LACPDUs Illegal Pkts 48 show lacp internal display description 49 show lacp neighbors display description 50 show lacp sysid display description Mac-address-table static Address Table Commands51 Address Table Commands Function Mode Action Show mac-address-table Clear mac-address-table dynamicMac-address- MAC address Mask Bits to match in the address Mac-address-table aging-time Sort Sort by address, vlan or interface Show mac-address-table aging-time Spanning Tree Commands 52 Spanning Tree Commands Function Mode Spanning tree is enabled Spanning-tree modeSyntax No spanning-tree Default Setting Spanning-tree Spanning-tree forward-time Spanning-tree hello-time Spanning-tree max-age Spanning-tree priority Spanning-tree pathcost method Long method Spanning-tree transmission-limit Spanning-tree mst-configurationThis command limits the maximum transmission rate for BPDUs Count The transmission limit in seconds. Range Mst priority MST ConfigurationMst vlan No mst instanceid vlan vlan-range Syntax Name name Switch’s MAC addressName Name Name of the spanning tree Syntax Revision number RevisionMax-hops Max-hopshop-number This example disables the spanning tree algorithm for port Spanning-tree spanning-disabledSyntax No spanning-tree spanning-disabled Default Setting Spanning-tree cost Spanning-tree port-priority Priority The priority for a port. Range 0-240, in steps Spanning-tree edge-port Syntax No spanning-tree edge-port Default SettingSyntax No spanning-tree portfast Default Setting Spanning-tree portfast Spanning-treeedge-port4-156 Spanning-tree link-typeAuto Spanning-tree mst cost Spanning-tree mst port-priority Spanning-tree mst port-priority4-159 Show spanning-tree Port-channel channel-idRange Command ModeSpanning-tree protocol-migration Syntax Spanning-tree protocol-migration interface Mstp Show spanning-tree mst configuration 53 VLANs Command Groups Function Vlan CommandsGvrp and Bridge Extension Commands 54 Gvrp and Bridge Extension Commands Function Mode Bridge-ext gvrp Syntax No bridge-ext gvrp Default SettingShow bridge-ext Syntax No switchport gvrp Default Setting Switchport gvrpShow gvrp configuration Syntax Show gvrp configuration interface Garp timer Show garp timer Editing Vlan Groups Syntax Show garp timer interface55 Editing Vlan Groups Command Function Mode Vlan database Vlan By default only Vlan 1 exists and is activeVlan Database Configuration Show vlan Interface vlan Configuring Vlan Interfaces56 Configuring Vlan Interfaces Command Function Mode Interface vlan All ports are in hybrid mode with the Pvid set to Vlan Switchport modeSwitchport acceptable-frame-types4-171 Switchport mode Switchport acceptable-frame-typesSwitchport ingress-filtering All frame types Switchport native vlan Switchport allowed vlan Switchport forbidden vlan No VLANs are included in the forbidden list Displaying Vlan Information 57 Show Vlan Commands Function ModeShow vlan General Configuration Guidelines for QinQ Configuring Ieee 802.1Q Tunneling58 Ieee 802.1Q Tunneling Commands Function Mode Dot1q-tunnel system-tunnel-control Switchport dot1q-tunnel mode Show dot1q-tunnel4-178 Show interfaces switchport This command displays information about QinQ tunnel ports Switchport dot1q-tunnel tpidRelated Commands Show dot1q-tunnel 59 Private Vlan Commands Function Mode Switchport dot1q-tunnel modePvlan Show pvlan This command displays the configured private VlanNo private VLANs are defined Protocol-vlan protocol-group Configuring Groups Configuring Protocol-based VLANs60 Protocol-based Vlan Commands Function Mode No protocol groups are configured Protocol-vlan protocol-group Configuring InterfacesNo protocol groups are mapped for any interface Show interfaces protocol-vlan protocol-group Show protocol-vlan protocol-groupSyntax Show protocol-vlan protocol-group group-id 61 Priority Commands Command Groups Function Priority CommandsPriority Commands Layer 62 Priority Commands Layer Function Mode Switchport priority default Queue modeSyntax Queue mode strict wrr no queue mode Weights 1, 2, 4, 8 are assigned to queues 0-3 respectively Queue bandwidth weight1...weight4 no queue bandwidthQueue bandwidth Queue cos-map 63 Default CoS Values to Egress QueuesQueue cos-mapqueueid cos1 ... cosn no queue cos-map This command shows the current queue mode Show queue modeFollowing example shows how to change the CoS assignments Show queue bandwidth 64 Priority Commands Layer 3 Function Mode Priority Commands Layer 3This command shows the class of service priority map Show queue cos-map Map ip dscp dscp-value cos cos-value no map ip dscp Syntax No map ip dscp Default Setting65 IP Dscp to CoS Vales IP Dscp Value CoS Value Show map ip dscp This command shows the IP Dscp priority mapSyntax Show map ip dscp interface Quality of Service Commands 198 Service-policy 66 Quality of Service Commands Function Mode199 Input of a particular interface Show class-map Syntax No class-map class-map-namematch-any Class-mapMatch Show class map Policy-map Class Map ConfigurationNo policy-mappolicy-map-name Class Policy Map ConfigurationNo class class-map-name Policy Map Class Configuration Set Syntax No police rate-kbpsburst-byteexceed-action drop set PoliceDrop out-of-profile packets Show class-map Service-policySyntax No service-policy input policy-map-name Syntax Show class-map class-map-name Show policy-mappolicy-map-name class class-map-name Show policy-mapShow policy-map interface Displays all policy maps and all classes 67 Multicast Filtering Commands Command Groups Function Multicast Filtering CommandsIgmp Snooping Commands 68 Igmp Snooping Commands Function Mode Ip igmp snooping Syntax No ip igmp snooping Default SettingFollowing example enables Igmp snooping Ip igmp snooping vlan static Ip igmp snooping version Following configures the switch to use Igmp VersionSyntax No ip igmp snooping leave-proxy Default Setting Ip igmp snooping leave-proxy This command shows the Igmp snooping configuration Syntax No ip igmp snooping immediate-leave Default SettingInterface Configuration Vlan Ip igmp snooping immediate-leave This command shows known multicast addresses Following shows the current Igmp snooping configurationShow mac-address-table multicast Syntax No ip igmp snooping querier Default Setting Igmp Query Commands Layer69 Igmp Query Commands Layer Function Mode Ip igmp snooping querier Times Following shows how to configure the query count toIp igmp snooping query-interval Ip igmp snooping query-max-response-time4-208 Ip igmp snooping query-max-response-time Seconds The report delay advertised in Igmp queries. RangeIp igmp snooping router-port-expire-time Ip igmp snooping vlan mrouter Static Multicast Routing Commands70 Static Multicast Routing Commands Function Mode Syntax No ip igmp snooping vlan vlan-idmrouter interface Syntax Show ip igmp snooping mrouter vlan vlan-id Displays multicast router ports for all configured VLANsShow ip igmp snooping mrouter Multicast router port types displayed include Static Syntax No ip igmp filter Default Setting Igmp Filtering and Throttling Commands71 Igmp Filtering and Throttling Commands Function Mode 213 Permit, deny Syntax Permit deny Default SettingIp igmp profile Syntax No ip igmp profile profile-number No range low-ip-address high-ip-address RangeSyntax No ip igmp filter profile-number Ip igmp max-groups Syntax Ip igmp max-groups number No ip igmp max-groups Syntax Ip igmp max-groups action replace deny Ip igmp max-groups actionShow ip igmp filter Syntax Show ip igmp filter interface interface Syntax Show ip igmp profile profile-number Show ip igmp profileShow ip igmp throttle interface Syntax Show ip igmp throttle interface interface Port Port number. Range Port-channelchannel-id Range Multicast Vlan Registration Commands72 Multicast Vlan Registration Commands Function Mode 219 Command Line Interface Mvr Global Configuration No mvr group ip-address count vlan vlan-id Multicast Filtering Commands Mvr Interface Configuration 220 Syntax Show mvr interface interface members ip-address Show mvr73 show mvr display description 75 show mvr members display description 74 show mvr interface display descriptionMembers Ip address IP Interface Commands76 IP Interface Commands Function Mode 224 Gateway IP address of the default gateway Ip default-gatewaySyntax Ip default-gateway gateway no ip default-gateway Following example defines a default gateway for this device Ip dhcp restart This command submits a Bootp or Dhcp client requestThis command displays the settings of an IP interface Show ip interface Show ip redirects Ip default-gateway4-224This command has no default for the host Ping 77 IP Source Guard Commands Function Mode IP Source Guard CommandsIp source-guard Syntax Ip source-guard sip sip-macno ip source-guard Ip source-guard binding This example enables IP source guard on portNo configured entries No ip source-guard binding mac-addressvlan vlan-id Show ip source-guard binding This command shows the source guard binding tableShow ip source-guard Ip source-guard4-227 ip dhcp snooping Ip dhcp snooping vlan Syntax No ip dhcp snooping Default Setting Dhcp Snooping Commands78 Dhcp Snooping Commands Function Mode Ip dhcp snooping 232 Ip dhcp snooping vlan This example enables Dhcp snooping globally for the switchThis example enables Dhcp snooping for Vlan Ip dhcp snooping vlan 4-233 ip dhcp snooping trust Syntax No ip dhcp snooping trust Default Setting Ip dhcp snooping trust Ip dhcp snooping verify mac-address This example enables MAC address verificationIp dhcp snooping information option Ip dhcp snooping information policy This example enables the Dhcp Snooping Information OptionReplace Show ip dhcp snooping Switch Cluster Commands79 Switch Cluster Commands Function Mode Show ip dhcp snooping binding Cluster Syntax No cluster Default SettingDisplays current cluster Candidates in the network 242 Cluster ip-pool Cluster commanderSyntax No cluster commander Default Setting Syntax Cluster ip-pool ip-addressno cluster ip-pool Member-id- The ID number of the Member switch. Range RcommandSyntax Rcommand id member-id Cluster member Show cluster This command shows the switch clustering configurationThis command shows the current switch cluster members Show cluster members Show cluster candidates Appendix a Software Specifications Software Features Standards Management FeaturesGroups 1, 2, 3, 9 Statistics, History, Alarm, Event Igmp RFC 1112 IGMPv2 RFC 2236 RADIUS+ RFC Management Information Bases Management Information Bases a Software Specifications Table B-1 Troubleshooting Chart Symptom Action Using System Logs Class of Service CoS Access Control List ACLBoot Protocol Bootp Differentiated Services Code Point Service Dscp Generic Multicast Registration Protocol Gmrp Garp Vlan Registration Protocol GvrpGeneric Attribute Registration Protocol Garp Group Attribute Registration Protocol Garp Internet Group Management Protocol Igmp Igmp SnoopingIgmp Query In-Band Management Remote Authentication Dial-in User Service Radius Multicast SwitchingPort Authentication Network Time Protocol NTP Simple Network Time Protocol Sntp Secure Shell SSHSimple Network Management Protocol Snmp Spanning Tree Algorithm STA Virtual LAN Vlan XModem Index Numerics Gateway, default 3-14,4-224 Index Index-3 Index-4 Page Technical Support

SMC Networks SMC8150L2 manual Address Table Commands, Mac-address-table static, Action

Models: SMC8150L2