Manuals / Tandberg Data / Computer Equipment / Network Card

Tandberg Data 600 manual Securing the Internal Tape Drive

Models: 600

1 126

Download 126 pages 57.12 Kb

Page 58

Securing the Internal Tape Drive

Configuring and Installing an Internal Tape Drive with SCSI Interface	SDLT 600 Product Manual

Figure 4-4shows two perspective views of the internal tape drive.

Front View

Rear View

Figure 4-4.SDLT 600 Tape Drive—Front and Rear Views

Securing the Internal Tape Drive

This section describes how to mount and secure the tape drive in the system.

NOTE: In some system configurations, it may be more convenient to connect the SCSI bus and power cables to the tape drive before securing it in the system.

Because of the variety of mounting possibilities for tape drives, the instructions presented here are general in nature. Use these instructions only as a guide for mounting the tape drive in your system.

Mount the tape drive in the system by performing the following steps:

1.Position the tape drive in the system and align the tape drive mounting holes (side or bottom) with those in the system. Figure 4-5 on page 4-11shows the mounting locations and dimensions for the tape drive.

CAUTION The screws used to mount the tape drive must be M3 x 8mm long. This type of screw is exactly the proper length and will not damage the tape drive.

2.Using four M3 x 8mm long screws, secure the tape drive in the bay or chassis.

4-10

March 2004

81-81184-02 REV A01

Image 58

Tandberg Data 600 manual Securing the Internal Tape Drive

Contents

SDLT 600 Product Manual Legal Disclaimers CopyrightTrademarks Contact InformationRevision History AchtungPage This Class B digital apparatus complies with Canadian ICES-003 SDLT 600 Product Manual 1 Introduction Table of Contents2 SDLT 600 Tape Drive Product Information 3 SDLT 600 Tape Drive Specifications 5 Using Your Tape Drive 4 Installing Your Tape DriveConfirming the Installation ASuper DLTtape I and Super DLTtape II Data Cartridges . . . . . . A-1 6 Regulatory ComplianceGlossary G-1 1 Introduction List of Tables3 SDLT 600 Tape Drive Specifications Table 1-1. Typographical Conventions6 Regulatory Compliance 4 Installing Your Tape Drive5 Using Your Tape Drive ASuper DLTtape I and Super DLTtape II Data Cartridges . . . . . . A-14 Installing Your Tape Drive List of Figures3 SDLT 600 Tape Drive Specifications 5 Using Your Tape DriveFigure A-1. Super DLTtape Data Cartridges Read by SDLT 600 Tape Drive . . . . . . . . . . . . . . . . . A-2 Figure A-2. Bottom View of Super DLTtape II Data Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 Figure A-3. Super DLTtape II Data Cartridge Reel Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5 Figure A-4. Opening the Super DLTtape II Data Cartridge Door . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5 Figure A-5. Problems to Look for Inside the Data Cartridge Door. . . . . . . . . . . . . . . . . . . . . . . . . . A-6 Figure A-6. Write-Protect Switch on Super DLTtape II Data Cartridge . . . . . . . . . . . . . . . . . . . . . . A-7 Figure A-7. Loading a Super DLTtape II Data Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9 ASuper DLTtape I and Super DLTtape II Data Cartridges . . . . . . A-11.1 Purpose and Scope IntroductionCHAPTER 1.3 Related Documents 1.2 Referenced Documents1.4 Structure of this Manual Element 1.5 Conventions1.6 For More Information ConventionMarch 1.7 Reader CommentsReader Comments SDLT 600 Product Manual2.1 Overview SDLT 600 Tape Drive Product InformationCHAPTER 2.2 Product Features 2.3.1 Laser Guided Magnetic Recording 2.3 Tape Drive Technology2.3.2 Pivoting Optical Servo 2.3.5 Advanced Metal Powder Media 2.3.3 Magneto Resistive Cluster Heads2.3.4 Advanced Partial Response Maximum Likelihood 2.3.6 Positive Engagement Tape Leader Buckling Mechanism2.4 Modular Design 2.4.2 Tape Control Module 2.4.1 Data Control ModuleTCM PCBA Data Cartridge Receiver 2.4.3 Front Panel ModuleBase Plate Positive Engagement Tape Leader Buckling Mechanism2.4.4 Electronic Interface Module 2.4.5 Super DLTtape II Data Cartridge2.5 Quantum Diagnostics Tools 2.6 TapeAlert2.7 Medium Auxiliary Memory 3.1.1 Host Interface SDLT 600 Tape Drive Specifications3.1 Product Specifications CHAPTERUltra 160 SCSI Interface 3.1.2 Physical Interface Fibre Channel InterfaceTable 3-3. SDLT 600 Tape Drive Physical Dimensions 3.1.3 Physical Dimensions and Weights3.1.4 Compression Table 3-4 shows the weights of the SDLT 600 tape drive3.1.5 Storage Capacity 3.1.6 Data Integrity3.1.7 Maximum Data Transfer Rate 3.1.8 Head Life and MTBF3.1.10 Data Cartridge Life Expectancy 3.1.9 Media Durability3.1.11 Positive Engagement Tape Leader Buckling Mechanism 3.2 Functional Specifications 3.2.1 Performance DataTable 3-12. Non-Operating Shock Specifications Packaged, Drop 3.2.2 Shock and Vibration SpecificationsTable 3-11. Non-Operating Shock Specifications Unpackaged Table 3-13. Non-Operating Vibration Specifications UnpackagedTable 3-14. Non-Operating Vibration Specifications Packaged Table 3-15. Operating Shock and Vibration Specifications3.2.3 Current and Power Requirements Table 3-16. Current and Power Requirements SCSI Interface Table 3-17. Current and Power Requirements Fibre Channel Interface Mode3.2.4 SDLT 600 Tape Drive System Recording Method 3.3 Environmental Specifications3.3.1 Air Flow Requirements 3.3.2 Temperature and Humidity 3.3.3 Storage and Shipment3.3.4 Altitude 3.4 Recording Media Specifications3.4.1 Media Structure High Coercivity Magnetic Layer Under Layer Enhanced Base Film Layer 3.4.2 Physical Data CartridgeChapter 3 SDLT 600 Tape Drive Specifications Back Coat Layer with Servo Guides3.4.3 Media Shipping, Operating, and Storage Specifications 3.4.4 Backward-Read Compatibility Transfer Rates SDLT 600 Product Manual Recording Media SpecificationsMarch 3-204.1 Warranty Note Installing Your Tape DriveCHAPTER 4.2 Safety, Handling, and ESD Protection 4.2.1 Safety Precautions4.2.2 Handling 4.2.3 Electrostatic Discharge Protection4.3 Pre-Installation Guidelines Model Number TR 4.4.1 Setting the Internal Tape Drive SCSI ID Table 4-1. SCSI ID Address Selections Graphical Format March Configuring and Installing an Internal Tape Drive with SCSI Interface0 = NO JUMPER INSTALLED, 1 = JUMPER INSTALLED SDLT 600 Product Manual4.4.2 Configuring the Internal Tape Drive for TERMPWR 4.4.3 Installing the Internal Tape DriveSecuring the Internal Tape Drive Connecting the Internal Tape Drive Cables SCSI and Power Connectors Optional Loader ConnectorDiagnostic use only Figure 4-6. Connectors on the Back Panel of SDLT 600 Tape DriveTable 4-3. MSE and SE Mode SCSI Connector Pin Assignments Loader ConnectorSignal Name Table 4-3. MSE and SE Mode SCSI Connector Pin Assignments ContinuedSignal Name Pin NumberSignal Name Table 4-4. MSE LVD Mode SCSI Connector Pin AssignmentsSignal Name Pin NumberTable 4-5. 4-Pin Power Connector Pin Assignments Table 4-4. MSE LVD Mode SCSI Connector Pin Assignments ContinuedTable 4-6. 8-Pin Loader Connector Pin Assignments 4.5.1 Fibre Channel Introduction 4.5.2 Secure the Tape Drive 4.5.3 Connect the Power 4.5.4 Optional Loader Connector4.6 Configuring and Installing a Tabletop Tape Drive 4.5.5 Connect the Fibre Channel Cable4.6.1 Configuring the Tape Drive SCSI IDTERMPWR 4.6.2 Installing the Tabletop Tape DriveSCSI Cables 5. Snap the wire cable clamps into place to secure the cables AC Power Cable 4.7 Confirming the Installation SDLT 600 Product Manual Confirming the InstallationMarch 4-265.1 Power-On Self-Test Using Your Tape DriveCHAPTER Figure 5-1. SDLT 600 Tape Drive Front Panel LEDs 5.2 Performing a Trial Back-up 5.3 Updating the Firmware5.3.1 Update the Firmware Using the SCSI Bus 5.3.2 Create a CUP/FUP Data Cartridge5.3.3 Using a CUP/FUP Data Cartridge 5.4 Cleaning the Tape Mechanism 5.3.4 Firmware Code Update Troubleshooting5.4.3 Life Expectancy of the Cleaning Tape 5.4.1 Occasional Cleaning of Tape Head5.4.2 When to Use the Cleaning Tape 5.4.4 Compatibility of the Cleaning Tape5.4.5 Loading the Cleaning Tape Into a Tabletop Tape Drive 5.5 Front Panel Controls and LEDs Possible Data Cartridge Scenario LED Color/StateLED/Button Table 5-3. How to Interpret the Front Panel LEDs and Other ControlsColor/Symbol Action5.6 Troubleshooting 5.6.1 POST TroubleshootingThen… Table 5-4. Troubleshooting Chart ContinuedYou should… 5.6.2 Over Temperature Condition Regulatory Compliance 6.1 Safety Regulations6.1.1 Safety Certifications CHAPTER6.2.1 Electromagnetic Emissions 6.2 Electromagnetic Field Specifications6.2.2 Electromagnetic Interference Susceptibility 6.2.3 Immunity and ESD Limits Table 6-2. Electromagnetic Interference EMI Test Summary6.3 Acoustic Noise Emissions Data Cartridge Inspection Procedure Super DLTtape I and Super DLTtape II Data CartridgesA.1 Recognizing Quantum Super DLTtape I and II Data Cartridges Data Cartridge Write-protect Switch Loading a Data CartridgeSuper DLTtape A.2 Data Cartridge Handling GuidelinesSuper DLTtape Maintain clean and smoke-free operating and storage environments A.3 Data Cartridge Inspection Procedure Figure A-3. Super DLTtape II Data Cartridge Reel Locks Bent or towed-in appearance on one or both clips A.4 Data Cartridge Write-protect Switch Indicator Table A-1. Write-Protect Switch PositionsSwitch Position Write-protectA.5 Loading a Data Cartridge A.6 Unloading a Data Cartridge Data Cartridge Inspection Procedure DLTtape VS1 Data CartridgeB.1 Data Cartridge Handling Guidelines Data Cartridge Write-Protect Switch Loading a Data CartridgeMaintain clean operating, working, and storage environments B.2 Data Cartridge Inspection Procedure Appendix B DLTtape VS1 Data CartridgeFigure B-2. DLTtape VS1 Data Cartridge Reel Locks Figure B-4. Opening the DLTtape VS1 Data Cartridge Door A broken tape leader loop A swallowed tape leader loop B.3 Data Cartridge Write-Protect Switch B.4 Loading a Data Cartridge 81-81184-02 REV A01 B.5 Unloading a Data CartridgeSDLT 600 Product Manual MarchMarch Unloading a Data CartridgeB-10 SDLT 600 Product ManualGlossary Page Page Page Page Page Page Page Page Page G-11 SDLT 600 Product Manual G-12March 81-81184-02 REV A01Page Tandberg Publication Number 81-81184-02 A01March Quantum Publication Number 81-81184-02 A01 81-81184-02 REV A01