Setup Information | Telex IP-223 instruction

CHAPTER 4

Setup Information

The setup information for the IP-223 is accessed by using a web browser, such as Microsoft® Internet Explorer. This section describes the programming information for the IP-223. It includes information on setting the IP Address, accessing the IP-223 web setup windows, the setup window standards, and an explanation of the fields on each window used to program the IP-223.

Setting the IP Address Information

Before entering the setup information for the IP-223, the IP Address and Network Mask must be assigned to the IP-223 by the use of a web browser or Windows™ HyperTerminal™ if the assigned IP Address is not accessible on your network. Contact your network administrator to obtain the network IP Address and Mask.

For the IP-223 to interface successfully with the LAN or WAN, the IP Addresses of the IP-223 and your PC must be on the same subnet. IP Addresses consist of four numbers separated by periods. For example, 10.2.99.101. For more information on IP Addresses and subnets, consult your network administrator.

In order for the PC and the IP-223 unit to communicate via IP, both devices need to be in the same subnet.

NOTE: For operation on different subnets, a gateway address must be configured.

An example of IP Addresses residing in the same subnet:

PC IP Address:10.2.99.250

IP-223 IP Address:10.2.99.251

IP-223 Network Mask:255.255.255.0

To display the IP Address and Network Mask assigned to the IP-223, do the following:

1.Connect power to the IP-223.

The IP Address and subnet mask are displayed on the LCD momentarily upon power up.

2.To check the IP Address and subnet mask at any other time, press and hold the line button on the front panel of the IP-223, and then momentarily press the IC button.

The IP Address is displayed on the top line of the LCD, and the Network Mask is displayed on the bottom line of the LCD.

Verify the IP Address and Network Mask obtained from your network administrator to the IP-223 addresses.

If the IP Address and Network Mask need to be set up using the serial port, see “Using HyperTerminal” below.

33

Image 31

Telex IP-223 technical manual Setup Information, Setting the IP Address Information

Contents

Model IP-223 Remote Adapter Panel Technical Manual Sales Contents General Gain Setup Save to Eeprom Window Update Firmware Figures Call Type Drop Down Menu iDEN Mode List Tables Page Operating Modes Overview Console Mode Connection Features Part Number Description IP-223 Accessories Test and Adjustment Points IP-223 SpecificationsFront Panel IC Button Handset JackLCD Display TX LED Line Button Jumper position Connection type 10/100 Ethernet ConnectorSerial Connector Back Panel Power Connection Radio 1 and Radio 2 Line 1 and Line 2 Connectors Ctcss Pin # Signal Cable color Overview Bandwidth Network RequirementsMulticast Network Performance Internet Group Management Protocol Igmp Local/Radio Connections To adjust the position of a jumper, do the followingJumper Positions Installation and Level Settings RX Audio Connection TX Audio ConnectionLine 1 jumpers J3, J9, and J11 R1 and R2 Relays COR Carrier Operated Relay I/O Input/OutputPTT Connection Monitor Connection Digital I/O Wire Jumper SettingsTX Side Settings Tone/Console Operation Supervisory I/O Level AdjustmentsLocal PTT I/O Cross Mute I/O Radio/Line RX Level Line TX Monitor Level Tone and Console Mode onlyGeneral Alignment Radio/Line TX Level Ctcss Level Frequency Decoding Setting the IP Address Information Setup Information Com1 Properties window appears Using HyperTerminal Main HyperTerminal window appears Enter Password for Factory Setup appears Serial port access window shown in appears Close the HyperTerminal program To access the IP-223 web setup windows, do the following Accessing IP-223 Web Browser Configuration Windows Links IP-223 Web Setup Windows StandardsLink Description Click Save to Eeprom To permanently save changes, do the followingClick Save Parameters To change the name of the IP-223 unit, do the following Welcome Window Serial Number Field Basic Ethernet Setup WindowMAC Address Unit IP Address Field Packet Delay before Playback FieldQOS Quality of Service Precedence Bits Field Use Dhcp Server Check Box Routing R Local Computer IP Address 1-10 Fields Submit Button To configure the IP-223 for use, do the following Receive Gain Drop Down Menu General Gain SetupHandset Mic Gain Drop Down Menu Handset Sidetone Gain Drop Down Menu Ctcss Gain Drop Down Menu Transmit Gain Drop Down MenuTX Voice Gain Field Enable via Ethernet Check Box Multicast Address Setup WindowLine Number Field Line Name Field Line Type Drop Down MenuRX Mcast Address Field TX Group Port Field RX Port FieldTX Mcast Address Field TX Port Field Vocoder Type Drop Down Menu Enable Check BoxMulticast Address Field Name Field Outgoing Port FieldIncoming Port Field Port Field Mcast Address Field Per Line Setup Window Line 1 Button Per Line Setup Local, Tone, and Console Modes view COR Enabled Check Box LAM Enabled Check BoxCOR Active High check box Update Button TX Delay FieldRX Delay Field Squelch Tail Delay Field Relay Time ms Field Tone Enable Check BoxRelay Drop Down Menu Relay Group Drop Down Menu System Field Local Mode Digital Output Field Local Mode OnlyCtcss Freq Field Local Mode Only Ctcss Default Check Box Local Mode Only LAM Time Field LAM Level Field Options Parallel Console Check Box PTT Timeout FieldWire Check Box Serial Port Mode Drop Down Menu Serial Port Params Drop Down Menu Serial Port Drop Down Menu Local Mode FleetSync Decode Check Box Tone and Local Modes Signaling Setup Tone Type Drop Down Menu FleetSync Encode Check Box Local Mode OnlyMDC Decode Check Box Tone and Local Modes MDC Encode Check Box Pause Duration Field ANI Suffix FieldDigit Duration Field Interdigit Duration Field ANI Call Format Field ANI Call Type Drop Down Menu Auto Answer Field Per Line Setup Window-Phone Mode ConfigurationAuto Disconnect Time Field Click Dial String Field Mic Click Call Enabled Check BoxNumber of Clicks Field Time Between Clicks Field Relay Closure R1 Ring Check Box Click Dial Timeout Field Detect Tones Enabled Check Box Rx AGC Enabled Check BoxKeep Alive Digits Enabled Check Box Star/Pound Keying Enabled Check Box Serial Port Parameters Drop Down Menu Serial Port Mode Drop Down Menu Serial Port Params Drop Down Menu Phone Mode MDC Decode Check Box FleetSync Decode Check Box ANI Decoder Field ANI Call Type Drop Down Menu Per Line Setup Window-iDEN Radio Configuration Per Line Setup iDEN Radio Mode view Jump To Entry Drop Down Menu IDEN Number Field Call Type Drop Down Menu Per Line Setup iDEN Mode view F1 Last Call Check Box iDEN Mode only PTT Timeout Field Per Line Setup Tetra Mode view Per line Setup Window-Tetra Radio Configuration Relay Drop Down Menu ISSI/GSSI Number Field Type Drop Down Menu TX Delay Field LAM Level Field PTT Timeout Field Save Parameters Button Reset IP-223 ButtonClick Reset IP-223 Save to Eeprom Window Admin System Account Account Setup WindowUser System Account Username Display Column Enable Check BoxPassword Field New Password Field Save Button Confirm Password FieldTo enable the user account, do the following Edit Button Add New User Button Reset System Parameters ButtonEdit System Accounts Window Delete Button Password can be 4-16 alpha-numeric characters in length Choose a Username Add New User WindowUsername Field CRP Setup & PIN Table Check Box Additional Feature Check BoxAccount Setup Check Box Basic Ethernet & Multicast Setup Check Box Tone Freq & Durations Check Box Cancel Button Edit Created Accounts Window Edit Created Account-Account Setup To activate a special feature, do the following Additional Feature Setup Window100 101 Clone Console Window 102 Crosspatch Setup Window 103 RCP Tables 104Jump To Entry Drop Down Menu and Go Button Phone Field Dial option only Mode Drop Down Menu105 Delete String Field 106 Command Buttons Submit 107Next 10 Button To define the crosspatch parameters, do the following 108 CRP PIN Table Window PIN Field PIN Enable Check Box109 Entry Field To define crosspatch PIN numbers, do the following 110Prev 30 Entries Button Next 30 Entries Button 111 Pass Change Window 112 Tone Frequency & Durations WindowMonitor Frequency Field 113 FTone 1-16 Frequency Fields 114Function Tone Duration Field Function Tone Magnitude Field 115 116 Install TSM Update Firmware117 118 Confirm Installation Download Telex Firmware 119 Firmware File Info Group Box Update Firmware Tool Window120 121 Login Group BoxUpload VoIP Hardware Firmware 122 Firmware Update Tool- Success Messages Click Close Signal Line Test point ConnectorsAdjustments Connector Description PCB 750743 or PCB 750630 revision C, D, E, and F Jumper Settings124 PCB 750743 or PCB 750630 revision F 125 Jumper Locations 126 127 Additional Resources 128 Relm RM Series Radios to 223 Series Adaptor Panels 129 Relm GMH Radios to IP-223 Adaptor Panels 130 131 Ctcss Tone Frequency TableTone Freq Number 132 133 Digital Output TableDigital Output Values 134 European Tone Frequencies in Hz Motorola Tone Frequency Table135 Tone Number Code Digit 136 137