Telex IP-223 20, SERIAL DB9 PINOUT

Overview

Radio 1 and Radio 2 (Line 1 and Line 2) Connectors

Two (2) DB25 connectors are provided for connection to various audio devices. The pinouts shown in Table4 are used when

custom cables need to be fabricated.

Power Connection

The IP-223 requires +12 to +16VDC, ~700mA of clean power. A 3-pin screw terminal receptacle is provided on the right rear

of the unit, pin 1 is the positive terminal, pin 2 is the ground terminal, and pin 3 is the earth ground terminal.

As with all communication equipment earth ground should be used. Earth ground is a low impedance path to earth for the

purpose of discharging lightening, static, and radiated energy.

SERIAL DB9 PINOUT

SIGNAL LINE # DB9 PIN #

TX 232 1 2

RX 232 1 3

TX TTL 1 9

RX TTL 1 1

Ground both 5

TX 232 2 8

RX 232 2 7

TX TTL 2 4

RX TTL 2 6

TABLE 3. DB9 Pinout

Contents

Main PROPRIETARY NOTICE C OPYRIGHT N WARRANTY NOTICE (LIMITED) F ACTORY S ERVICE C P HONE N Table of Contents OVERVIEW..................................................... 13 Operating Modes ..................................................13 Back Panel ............................................................19 COMMUNICATIONS SYSTEM DESIGN.... 23 General Gain Setup .............................................47 Multicast Address Setup Window ........................49 Phone Mode Configuration .................................69 iDEN Radio Configuration ...................................77 Tetra Radio Configuration .................................. 84 Save to EEPROM Window ................................... 90 Account Setup Window ........................................ 91 CRP PIN Table Window .................................... 108 UPDATE FIRMWARE ................................. 117 Update Firmware ............................................... 117 IP-223 SETTINGS - QUICK REFERENCE 123 List of Figures Page Page Page Overview Operating Modes Page IP-223 Accessories IP-223 Specifications Front Panel Test and Adjustment Points Page Page Back Panel 10/100 Ethernet Connector Serial Connector 20 Radio 1 and Radio 2 (Line 1 and Line 2) Connectors Power Connection SERIAL DB9 PINOUT Page Page Communications System Design Network Requirements Internet Group Management Protocol (IGMP) Network Performance Installation and Level Settings Local/Radio Connections Jumper Positions Page Page COR (Carrier Operated Relay) I/O (Input/Output) PTT Connection Monitor Connection R1 and R2 Relays Digital I/O Tone/Console Operation 2-/4-Wire Jumper Settings TX Side Settings Local PTT I/O Cross Mute I/O Level Adjustments Page CTCSS Level Frequency Decoding Setup Information Setting the IP Address Information Using HyperTerminal 35 Page Page Page Accessing IP-223 Web Browser Configuration Windows IP-223 Web Setup Windows Standards Links > Welcome Window Basic Ethernet Setup Window Page QOS: D, T, and R (Delay, Throughput, and Reliability) Bits Field Local Computer IP Address 1-10 Fields Page General Gain Setup Handset Mic Gain Drop Down Menu Handset Sidetone Gain Drop Down Menu Receive Gain Drop Down Menu Transmit Gain Drop Down Menu CTCSS Gain Drop Down Menu TX Voice Gain Field Multicast Address Setup Window Line Number Field Enable via Ethernet Check Box Line Type Drop Down Menu Line Name Field RX Mcast Address Field RX Port Field TX Mcast Address Field TX Port Field TX Group Port Field TTL Field Vocoder Type Drop Down Menu Enable Check Box Line Name Field Multicast Address Field Page Page Per Line Setup Window Page 57 Line 2 Button Line Mode Status Field Port Enabled Check Box LAM Enabled Check Box Page Tone Enable Check Box Relay Drop Down Menu Page Page Options PTT Timeout Field Page Page Page Page Page Per Line Setup WindowPhone Mode Configuration TX Delay Field RX Delay Field Page Page Serial Port Mode Drop Down Menu Serial Port Parameters Drop Down Menu Page Page Page Per Line Setup WindowiDEN Radio Configuration Page Page Call Type Drop Down Menu iDEN Number Field Page Page Page Per line Setup WindowTetra Radio Configuration Jump To Entry Drop Down Menu Update Button Tone Enable Check Box Relay Drop Down Menu Type Drop Down Menu ISSI/GSSI Number Field TX Delay Field RX Delay Field Page PTT Timeout Field Serial Port Mode Drop Down Menu Serial Port Parameters Drop Down Menu Save to EEPROM Window Save Parameters Button Reset IP-223 Button Account Setup Window Page Page Edit System Accounts Window Page Add New User Window Page Page Edit Created Accounts Window Additional Feature Setup Window Clone Console Window Page Page RCP Tables Jump To Entry Drop Down Menu and Go Button Page Command Buttons Page CRP PIN Table Window Page Page Pass Change Window Tone Frequency & Durations Window Monitor Frequency Field Page Function Tone Duration Field Function Tone Magnitude Field FTone 1-16 Frequency Fields Page Page Update Firmware Update Firmware Install TSM Page Download Telex Firmware 120 Update Firmware Tool Window Firmware File Info Group Box 121 Login Group Box Upload VoIP Hardware Firmware Page IP-223 Settings - Quick Reference I/O Connectors Adjustments Jumper Settings PCB 750743 or PCB 750630 revision F PCB 750743 or PCB 750630 revision C, D, E, and F PCB 750630 revision A Page Page Appendix A Additional Resources Additional Resources FILE Application Guides AN-VEGA-10 Moto XTL-5000 Motorola XTL - 5000 Radios to 223 Series Adapter Panel Creating Cross Band Repeaters or Extended Radio Coverage Using IP-223s Page iDEN Radio Control on Legacy Tone Systems using IP-223s Motorola - MCS2000 Radios to 223 Series Adaptor Panels ICOM - IC-F121/221 Series Radio to 223 Series Adaptor Panels Kenwood - TK-6110 Series Radio to 223 Series Adaptor Panels Page CTCSS Tone Fr equency Table CTCSS Tone Frequency Table Page APPENDIX C Digital Output Table DIG0 DIG1 DIG2 DIG3 Page APPENDIX D Tone Fr equency Table Code Digit Tone Num ber Tone Frequency Table European Tone Frequencies in Hz Motorola