Installation and Level Settings | Telex IP-223 guide

Installation and Level Settings

3.Carefully slide the case top forward past the IC and LINE buttons, and then lift up to gain access to the PCB (Printed Circuit Board) as shown in Figure 83.

Case top

PCB assembly

FIGURE 83. IP-223 PCB Assembly

4.Locate the desired jumper on the PCB assembly and use needle nose pliers to adjust the jumper, if necessary.

5.Carefully lift up the case top and place it into position on the chassis bottom.

6.Secure the case top into position using the six (6) screws.

7.Connect power to the IP-223 unit.

26

Image 24

Telex IP-223 technical manual Installation and Level Settings

Contents

Model IP-223 Remote Adapter Panel Technical Manual Sales Contents General Gain Setup Save to Eeprom Window Update Firmware Figures Call Type Drop Down Menu iDEN Mode List Tables Page Overview Operating Modes Features Console Mode Connection IP-223 Accessories Part Number Description IP-223 Specifications Test and Adjustment PointsFront Panel Handset Jack IC ButtonLCD Display Line Button TX LED 10/100 Ethernet Connector Serial ConnectorBack Panel Jumper position Connection type Radio 1 and Radio 2 Line 1 and Line 2 Connectors Power Connection Pin # Signal Cable color Ctcss Overview Network Requirements BandwidthMulticast Internet Group Management Protocol Igmp Network Performance To adjust the position of a jumper, do the following Local/Radio ConnectionsJumper Positions Installation and Level Settings TX Audio Connection RX Audio ConnectionLine 1 jumpers J3, J9, and J11 COR Carrier Operated Relay I/O Input/Output PTT ConnectionMonitor Connection R1 and R2 Relays Wire Jumper Settings TX Side SettingsTone/Console Operation Digital I/O Level Adjustments Local PTT I/OCross Mute I/O Supervisory I/O Line TX Monitor Level Tone and Console Mode only General AlignmentRadio/Line TX Level Radio/Line RX Level Frequency Decoding Ctcss Level Setup Information Setting the IP Address Information Using HyperTerminal Com1 Properties window appears Main HyperTerminal window appears Enter Password for Factory Setup appears Serial port access window shown in appears Close the HyperTerminal program Accessing IP-223 Web Browser Configuration Windows To access the IP-223 web setup windows, do the following IP-223 Web Setup Windows Standards LinksLink Description To permanently save changes, do the following Click Save to EepromClick Save Parameters Welcome Window To change the name of the IP-223 unit, do the following Basic Ethernet Setup Window Serial Number FieldMAC Address Packet Delay before Playback Field QOS Quality of Service Precedence Bits FieldUse Dhcp Server Check Box Unit IP Address Field Local Computer IP Address 1-10 Fields Routing R To configure the IP-223 for use, do the following Submit Button General Gain Setup Handset Mic Gain Drop Down MenuHandset Sidetone Gain Drop Down Menu Receive Gain Drop Down Menu Transmit Gain Drop Down Menu Ctcss Gain Drop Down MenuTX Voice Gain Field Multicast Address Setup Window Enable via Ethernet Check BoxLine Number Field Line Type Drop Down Menu Line Name FieldRX Mcast Address Field RX Port Field TX Mcast Address FieldTX Port Field TX Group Port Field Enable Check Box Vocoder Type Drop Down MenuMulticast Address Field Outgoing Port Field Name FieldIncoming Port Field Mcast Address Field Port Field Per Line Setup Window Per Line Setup Local, Tone, and Console Modes view Line 1 Button LAM Enabled Check Box COR Enabled Check BoxCOR Active High check box TX Delay Field RX Delay FieldSquelch Tail Delay Field Update Button Tone Enable Check Box Relay Drop Down MenuRelay Group Drop Down Menu Relay Time ms Field Digital Output Field Local Mode Only Ctcss Freq Field Local Mode OnlyCtcss Default Check Box Local Mode Only System Field Local Mode LAM Level Field LAM Time Field Options PTT Timeout Field Wire Check BoxSerial Port Mode Drop Down Menu Parallel Console Check Box Serial Port Drop Down Menu Local Mode Serial Port Params Drop Down Menu Signaling Setup FleetSync Decode Check Box Tone and Local Modes FleetSync Encode Check Box Local Mode Only MDC Decode Check Box Tone and Local ModesMDC Encode Check Box Tone Type Drop Down Menu ANI Suffix Field Digit Duration FieldInterdigit Duration Field Pause Duration Field ANI Call Type Drop Down Menu ANI Call Format Field Per Line Setup Window-Phone Mode Configuration Auto Answer FieldAuto Disconnect Time Field Mic Click Call Enabled Check Box Number of Clicks FieldTime Between Clicks Field Click Dial String Field Click Dial Timeout Field Relay Closure R1 Ring Check Box Rx AGC Enabled Check Box Keep Alive Digits Enabled Check BoxStar/Pound Keying Enabled Check Box Detect Tones Enabled Check Box Serial Port Mode Drop Down Menu Serial Port Parameters Drop Down Menu Serial Port Params Drop Down Menu Phone Mode FleetSync Decode Check Box MDC Decode Check Box ANI Decoder Field Per Line Setup Window-iDEN Radio Configuration ANI Call Type Drop Down Menu Per Line Setup iDEN Radio Mode view Jump To Entry Drop Down Menu Call Type Drop Down Menu IDEN Number Field Per Line Setup iDEN Mode view F1 Last Call Check Box iDEN Mode only PTT Timeout Field Per line Setup Window-Tetra Radio Configuration Per Line Setup Tetra Mode view Relay Drop Down Menu Type Drop Down Menu ISSI/GSSI Number Field TX Delay Field LAM Level Field PTT Timeout Field Reset IP-223 Button Click Reset IP-223Save to Eeprom Window Save Parameters Button Account Setup Window Admin System AccountUser System Account Enable Check Box Password FieldNew Password Field Username Display Column Confirm Password Field To enable the user account, do the followingEdit Button Save Button Reset System Parameters Button Edit System Accounts WindowDelete Button Add New User Button Password can be 4-16 alpha-numeric characters in length Add New User Window Choose a UsernameUsername Field Additional Feature Check Box Account Setup Check BoxBasic Ethernet & Multicast Setup Check Box CRP Setup & PIN Table Check Box Cancel Button Tone Freq & Durations Check Box Edit Created Account-Account Setup Edit Created Accounts Window Additional Feature Setup Window To activate a special feature, do the following100 Clone Console Window 101 Crosspatch Setup Window 102 103 104 RCP TablesJump To Entry Drop Down Menu and Go Button Mode Drop Down Menu 105Delete String Field Phone Field Dial option only Command Buttons 106 107 Next 10 ButtonTo define the crosspatch parameters, do the following Submit CRP PIN Table Window 108 PIN Enable Check Box 109Entry Field PIN Field 110 Prev 30 Entries ButtonNext 30 Entries Button To define crosspatch PIN numbers, do the following Pass Change Window 111 Tone Frequency & Durations Window 112Monitor Frequency Field 113 114 Function Tone Duration FieldFunction Tone Magnitude Field FTone 1-16 Frequency Fields 115 116 Update Firmware Install TSM117 Confirm Installation 118 119 Download Telex Firmware Update Firmware Tool Window Firmware File Info Group Box120 Login Group Box 121Upload VoIP Hardware Firmware Firmware Update Tool- Success Messages Click Close 122 Connectors AdjustmentsConnector Description Signal Line Test point Jumper Settings 124PCB 750743 or PCB 750630 revision F PCB 750743 or PCB 750630 revision C, D, E, and F Jumper Locations 125 126 Additional Resources 127 Relm RM Series Radios to 223 Series Adaptor Panels 128 Relm GMH Radios to IP-223 Adaptor Panels 129 130 Ctcss Tone Frequency Table 131Tone Freq Number 132 Digital Output Table 133Digital Output Values 134 Tone Frequency Table 135Tone Number Code Digit European Tone Frequencies in Hz Motorola 136 137