Firmware File Info Group Box, 120 | Telex IP-223 specs

Update Firmware Tool Window

NAVIGATION: Selecting Firmware Update Tool from the Tools menu opens the Firmware Update Tool window shown in Figure 138.

FIGURE 138. Firmware Update Tool

File Field

The File field is used to select a firmware file to upload to the VoIP hardware.

Firmware File Info Group Box

Device Type Field

The Device Type field displays the type of device supported by the currently selected file in the File field.

Firmware Version Field

The Firmware Version field displays the currently selected file’s firmware version.

Left Navigation Pane

The Left Navigation Pane displays all detected devices from the main dialog’s Device list with device types that match the currently selected firmware files. Manually entered IP Addresses also appear in the navigation pane. Once the device is added, it appears in the left navigation pane and is available for selection.

NOTE: If the device you are updating does not automatically appear in the navigation pane, manually enter the IP Address in the Manual Entry field.

120

Image 118

Telex IP-223 technical manual Firmware File Info Group Box, 120, Update Firmware Tool Window

Contents

Model IP-223 Remote Adapter Panel Technical Manual Sales Contents General Gain Setup Save to Eeprom Window Update Firmware Figures Call Type Drop Down Menu iDEN Mode List Tables Page Overview Operating Modes Features Console Mode Connection IP-223 Accessories Part Number Description Test and Adjustment Points IP-223 SpecificationsFront Panel IC Button Handset JackLCD Display Line Button TX LED Back Panel 10/100 Ethernet ConnectorSerial Connector Jumper position Connection type Radio 1 and Radio 2 Line 1 and Line 2 Connectors Power Connection Pin # Signal Cable color Ctcss Overview Bandwidth Network RequirementsMulticast Internet Group Management Protocol Igmp Network Performance Local/Radio Connections To adjust the position of a jumper, do the followingJumper Positions Installation and Level Settings RX Audio Connection TX Audio ConnectionLine 1 jumpers J3, J9, and J11 Monitor Connection COR Carrier Operated Relay I/O Input/OutputPTT Connection R1 and R2 Relays Tone/Console Operation Wire Jumper SettingsTX Side Settings Digital I/O Cross Mute I/O Level AdjustmentsLocal PTT I/O Supervisory I/O Radio/Line TX Level Line TX Monitor Level Tone and Console Mode onlyGeneral Alignment Radio/Line RX Level Frequency Decoding Ctcss Level Setup Information Setting the IP Address Information Using HyperTerminal Com1 Properties window appears Main HyperTerminal window appears Enter Password for Factory Setup appears Serial port access window shown in appears Close the HyperTerminal program Accessing IP-223 Web Browser Configuration Windows To access the IP-223 web setup windows, do the following Links IP-223 Web Setup Windows StandardsLink Description Click Save to Eeprom To permanently save changes, do the followingClick Save Parameters Welcome Window To change the name of the IP-223 unit, do the following Serial Number Field Basic Ethernet Setup WindowMAC Address Use Dhcp Server Check Box Packet Delay before Playback FieldQOS Quality of Service Precedence Bits Field Unit IP Address Field Local Computer IP Address 1-10 Fields Routing R To configure the IP-223 for use, do the following Submit Button Handset Sidetone Gain Drop Down Menu General Gain SetupHandset Mic Gain Drop Down Menu Receive Gain Drop Down Menu Ctcss Gain Drop Down Menu Transmit Gain Drop Down MenuTX Voice Gain Field Enable via Ethernet Check Box Multicast Address Setup WindowLine Number Field Line Name Field Line Type Drop Down MenuRX Mcast Address Field TX Port Field RX Port FieldTX Mcast Address Field TX Group Port Field Vocoder Type Drop Down Menu Enable Check BoxMulticast Address Field Name Field Outgoing Port FieldIncoming Port Field Mcast Address Field Port Field Per Line Setup Window Per Line Setup Local, Tone, and Console Modes view Line 1 Button COR Enabled Check Box LAM Enabled Check BoxCOR Active High check box Squelch Tail Delay Field TX Delay FieldRX Delay Field Update Button Relay Group Drop Down Menu Tone Enable Check BoxRelay Drop Down Menu Relay Time ms Field Ctcss Default Check Box Local Mode Only Digital Output Field Local Mode OnlyCtcss Freq Field Local Mode Only System Field Local Mode LAM Level Field LAM Time Field Options Serial Port Mode Drop Down Menu PTT Timeout FieldWire Check Box Parallel Console Check Box Serial Port Drop Down Menu Local Mode Serial Port Params Drop Down Menu Signaling Setup FleetSync Decode Check Box Tone and Local Modes MDC Encode Check Box FleetSync Encode Check Box Local Mode OnlyMDC Decode Check Box Tone and Local Modes Tone Type Drop Down Menu Interdigit Duration Field ANI Suffix FieldDigit Duration Field Pause Duration Field ANI Call Type Drop Down Menu ANI Call Format Field Auto Answer Field Per Line Setup Window-Phone Mode ConfigurationAuto Disconnect Time Field Time Between Clicks Field Mic Click Call Enabled Check BoxNumber of Clicks Field Click Dial String Field Click Dial Timeout Field Relay Closure R1 Ring Check Box Star/Pound Keying Enabled Check Box Rx AGC Enabled Check BoxKeep Alive Digits Enabled Check Box Detect Tones Enabled Check Box Serial Port Mode Drop Down Menu Serial Port Parameters Drop Down Menu Serial Port Params Drop Down Menu Phone Mode FleetSync Decode Check Box MDC Decode Check Box ANI Decoder Field Per Line Setup Window-iDEN Radio Configuration ANI Call Type Drop Down Menu Per Line Setup iDEN Radio Mode view Jump To Entry Drop Down Menu Call Type Drop Down Menu IDEN Number Field Per Line Setup iDEN Mode view F1 Last Call Check Box iDEN Mode only PTT Timeout Field Per line Setup Window-Tetra Radio Configuration Per Line Setup Tetra Mode view Relay Drop Down Menu Type Drop Down Menu ISSI/GSSI Number Field TX Delay Field LAM Level Field PTT Timeout Field Save to Eeprom Window Reset IP-223 ButtonClick Reset IP-223 Save Parameters Button Admin System Account Account Setup WindowUser System Account New Password Field Enable Check BoxPassword Field Username Display Column Edit Button Confirm Password FieldTo enable the user account, do the following Save Button Delete Button Reset System Parameters ButtonEdit System Accounts Window Add New User Button Password can be 4-16 alpha-numeric characters in length Choose a Username Add New User WindowUsername Field Basic Ethernet & Multicast Setup Check Box Additional Feature Check BoxAccount Setup Check Box CRP Setup & PIN Table Check Box Cancel Button Tone Freq & Durations Check Box Edit Created Account-Account Setup Edit Created Accounts Window To activate a special feature, do the following Additional Feature Setup Window100 Clone Console Window 101 Crosspatch Setup Window 102 103 RCP Tables 104Jump To Entry Drop Down Menu and Go Button Delete String Field Mode Drop Down Menu105 Phone Field Dial option only Command Buttons 106 To define the crosspatch parameters, do the following 107Next 10 Button Submit CRP PIN Table Window 108 Entry Field PIN Enable Check Box109 PIN Field Next 30 Entries Button 110Prev 30 Entries Button To define crosspatch PIN numbers, do the following Pass Change Window 111 112 Tone Frequency & Durations WindowMonitor Frequency Field 113 Function Tone Magnitude Field 114Function Tone Duration Field FTone 1-16 Frequency Fields 115 116 Install TSM Update Firmware117 Confirm Installation 118 119 Download Telex Firmware Firmware File Info Group Box Update Firmware Tool Window120 121 Login Group BoxUpload VoIP Hardware Firmware Firmware Update Tool- Success Messages Click Close 122 Connector Description ConnectorsAdjustments Signal Line Test point PCB 750743 or PCB 750630 revision F Jumper Settings124 PCB 750743 or PCB 750630 revision C, D, E, and F Jumper Locations 125 126 Additional Resources 127 Relm RM Series Radios to 223 Series Adaptor Panels 128 Relm GMH Radios to IP-223 Adaptor Panels 129 130 131 Ctcss Tone Frequency TableTone Freq Number 132 133 Digital Output TableDigital Output Values 134 Tone Number Code Digit Tone Frequency Table135 European Tone Frequencies in Hz Motorola 136 137