Serial Port Mode Drop Down Menu | Telex IP-223 instruction

Per Line Setup Window—Phone Mode Configuration

RP251/550 Setup

NOTE: These features support legacy PSTN radio control systems.

C550 Operation Enabled Check Box

The C550 Operation Enabled check box indicates whether or not operation of the C-550 console is enabled. If selected, operation of the C-550 console is enabled.

RP251 Operation Enabled Check Box

The RP251 Operation Enabled check box indicates whether or not operation of the RP-251 panel is enabled. If selected, operation of the RP-251 dial-up remote station panel is enabled.

RP251 Access Digits Field

The RP251 Access Digits field identifies the three (3) digit access code assigned to the RP-251 panel.

RP251 Connect Digits Field

The RP251 Connect Digits field identifies the three (3) digit connect code sent to the console at the time of connection.

Serial Port Mode

Serial Port Mode Drop Down Menu

The Serial Port Mode drop down menu is used to identify the specific radio interface for the serial port configuration. Selecting an item with a Scan List suffix enables a frequency scan list update function. The freq scan list function synchronizes the console scan list with the radio's scan list.

The serial port in Phone mode is, by default, Normal.

Serial Port Parameters Drop Down Menu

The Serial Port Params drop down menu identifies the configuration of the serial port data speed and format. Serial port parameters refer to bit rate, parity, data bits, and stop bits. The Baud rate is used in phone mode. If phone mode is enabled on line 1, this is the rate used to connect to the IP-223 via the HyperTerminal.

The default setting for the field, 19200.N.8.1, is not configurable.

If necessary, refer to the Radio Dispatch and Signaling Equipment downloads available on the Telex website (www.telex.com/RadioDispatch/) for this setting based on the radio to be installed.

73

Image 71

Telex IP-223 technical manual Serial Port Mode Drop Down Menu, Serial Port Parameters Drop Down Menu

Contents

Model IP-223 Remote Adapter Panel Technical Manual Sales Contents General Gain Setup Save to Eeprom Window Update Firmware Figures Call Type Drop Down Menu iDEN Mode List Tables Page Operating Modes Overview Console Mode Connection Features Part Number Description IP-223 Accessories Front Panel IP-223 SpecificationsTest and Adjustment Points LCD Display Handset JackIC Button TX LED Line Button Jumper position Connection type 10/100 Ethernet ConnectorSerial Connector Back Panel Power Connection Radio 1 and Radio 2 Line 1 and Line 2 Connectors Ctcss Pin # Signal Cable color Overview Multicast Network RequirementsBandwidth Network Performance Internet Group Management Protocol Igmp Jumper Positions To adjust the position of a jumper, do the followingLocal/Radio Connections Installation and Level Settings Line 1 jumpers J3, J9, and J11 TX Audio ConnectionRX Audio Connection R1 and R2 Relays COR Carrier Operated Relay I/O Input/OutputPTT Connection Monitor Connection Digital I/O Wire Jumper SettingsTX Side Settings Tone/Console Operation Supervisory I/O Level AdjustmentsLocal PTT I/O Cross Mute I/O Radio/Line RX Level Line TX Monitor Level Tone and Console Mode onlyGeneral Alignment Radio/Line TX Level Ctcss Level Frequency Decoding Setting the IP Address Information Setup Information Com1 Properties window appears Using HyperTerminal Main HyperTerminal window appears Enter Password for Factory Setup appears Serial port access window shown in appears Close the HyperTerminal program To access the IP-223 web setup windows, do the following Accessing IP-223 Web Browser Configuration Windows Link Description IP-223 Web Setup Windows StandardsLinks Click Save Parameters To permanently save changes, do the followingClick Save to Eeprom To change the name of the IP-223 unit, do the following Welcome Window MAC Address Basic Ethernet Setup WindowSerial Number Field Unit IP Address Field Packet Delay before Playback FieldQOS Quality of Service Precedence Bits Field Use Dhcp Server Check Box Routing R Local Computer IP Address 1-10 Fields Submit Button To configure the IP-223 for use, do the following Receive Gain Drop Down Menu General Gain SetupHandset Mic Gain Drop Down Menu Handset Sidetone Gain Drop Down Menu TX Voice Gain Field Transmit Gain Drop Down MenuCtcss Gain Drop Down Menu Line Number Field Multicast Address Setup WindowEnable via Ethernet Check Box RX Mcast Address Field Line Type Drop Down MenuLine Name Field TX Group Port Field RX Port FieldTX Mcast Address Field TX Port Field Multicast Address Field Enable Check BoxVocoder Type Drop Down Menu Incoming Port Field Outgoing Port FieldName Field Port Field Mcast Address Field Per Line Setup Window Line 1 Button Per Line Setup Local, Tone, and Console Modes view COR Active High check box LAM Enabled Check BoxCOR Enabled Check Box Update Button TX Delay FieldRX Delay Field Squelch Tail Delay Field Relay Time ms Field Tone Enable Check BoxRelay Drop Down Menu Relay Group Drop Down Menu System Field Local Mode Digital Output Field Local Mode OnlyCtcss Freq Field Local Mode Only Ctcss Default Check Box Local Mode Only LAM Time Field LAM Level Field Options Parallel Console Check Box PTT Timeout FieldWire Check Box Serial Port Mode Drop Down Menu Serial Port Params Drop Down Menu Serial Port Drop Down Menu Local Mode FleetSync Decode Check Box Tone and Local Modes Signaling Setup Tone Type Drop Down Menu FleetSync Encode Check Box Local Mode OnlyMDC Decode Check Box Tone and Local Modes MDC Encode Check Box Pause Duration Field ANI Suffix FieldDigit Duration Field Interdigit Duration Field ANI Call Format Field ANI Call Type Drop Down Menu Auto Disconnect Time Field Per Line Setup Window-Phone Mode ConfigurationAuto Answer Field Click Dial String Field Mic Click Call Enabled Check BoxNumber of Clicks Field Time Between Clicks Field Relay Closure R1 Ring Check Box Click Dial Timeout Field Detect Tones Enabled Check Box Rx AGC Enabled Check BoxKeep Alive Digits Enabled Check Box Star/Pound Keying Enabled Check Box Serial Port Parameters Drop Down Menu Serial Port Mode Drop Down Menu Serial Port Params Drop Down Menu Phone Mode MDC Decode Check Box FleetSync Decode Check Box ANI Decoder Field ANI Call Type Drop Down Menu Per Line Setup Window-iDEN Radio Configuration Per Line Setup iDEN Radio Mode view Jump To Entry Drop Down Menu IDEN Number Field Call Type Drop Down Menu Per Line Setup iDEN Mode view F1 Last Call Check Box iDEN Mode only PTT Timeout Field Per Line Setup Tetra Mode view Per line Setup Window-Tetra Radio Configuration Relay Drop Down Menu ISSI/GSSI Number Field Type Drop Down Menu TX Delay Field LAM Level Field PTT Timeout Field Save Parameters Button Reset IP-223 ButtonClick Reset IP-223 Save to Eeprom Window User System Account Account Setup WindowAdmin System Account Username Display Column Enable Check BoxPassword Field New Password Field Save Button Confirm Password FieldTo enable the user account, do the following Edit Button Add New User Button Reset System Parameters ButtonEdit System Accounts Window Delete Button Password can be 4-16 alpha-numeric characters in length Username Field Add New User WindowChoose a Username CRP Setup & PIN Table Check Box Additional Feature Check BoxAccount Setup Check Box Basic Ethernet & Multicast Setup Check Box Tone Freq & Durations Check Box Cancel Button Edit Created Accounts Window Edit Created Account-Account Setup 100 Additional Feature Setup WindowTo activate a special feature, do the following 101 Clone Console Window 102 Crosspatch Setup Window 103 Jump To Entry Drop Down Menu and Go Button 104RCP Tables Phone Field Dial option only Mode Drop Down Menu105 Delete String Field 106 Command Buttons Submit 107Next 10 Button To define the crosspatch parameters, do the following 108 CRP PIN Table Window PIN Field PIN Enable Check Box109 Entry Field To define crosspatch PIN numbers, do the following 110Prev 30 Entries Button Next 30 Entries Button 111 Pass Change Window Monitor Frequency Field Tone Frequency & Durations Window112 113 FTone 1-16 Frequency Fields 114Function Tone Duration Field Function Tone Magnitude Field 115 116 117 Update FirmwareInstall TSM 118 Confirm Installation Download Telex Firmware 119 120 Update Firmware Tool WindowFirmware File Info Group Box Upload VoIP Hardware Firmware Login Group Box121 122 Firmware Update Tool- Success Messages Click Close Signal Line Test point ConnectorsAdjustments Connector Description PCB 750743 or PCB 750630 revision C, D, E, and F Jumper Settings124 PCB 750743 or PCB 750630 revision F 125 Jumper Locations 126 127 Additional Resources 128 Relm RM Series Radios to 223 Series Adaptor Panels 129 Relm GMH Radios to IP-223 Adaptor Panels 130 Tone Freq Number Ctcss Tone Frequency Table131 132 Digital Output Values Digital Output Table133 134 European Tone Frequencies in Hz Motorola Tone Frequency Table135 Tone Number Code Digit 136 137